← FR 125, FR 135, FR 145 · FS 108 · FR 108

Stihl 4135 · Section K · 10 of 15 · 31 parts

Flexible shaft, Loop handle

Fits FR 108.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021212223232424252525252627283344041425566789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (31)

PosPart numberDescriptionQty
1 4135 710 3000 Flexible shaft 1
2 4132 711 3300 Flexible shaft 1
3 4132 711 8400 Rubber ring 2
4 4132 182 2100 Retainer 2
5 9645 945 7570 O-ring 15.54x2.62 2
6 4125 717 2000 Cap 2
7 4132 161 0505 Housing 1
8 4132 162 5000 Lever 1
9 4132 162 7800 Torsion spring 1
10 0000 958 0600 Washer 1
11 9460 624 0500 E-clip 5 1
12 9022 341 0950 Spline screw IS-M5x10 1
13 9022 341 1350 Spline screw IS-M6x25 1
14 4132 162 7600 Shaft 1
15 9503 003 8052 Grooved ball bearing 6901-2Z 1
16 9452 621 1130 Circlip 12x1 1
17 9456 621 2660 Circlip 24x1.2 1
18 4135 162 2800 Cap 1
19 4132 710 7100 Drive tube assembly Ø 26 mm / 1 1/16'' 1
20 4117 711 3200 Drive shaft 1
21 4130 790 1315 Loop handle 1
22 4130 790 8450 Barrier bar 1
23 9222 068 0900 Square nut M6 2
24 9022 341 1370 Spline screw IS-M6x30 2
25 4123 791 7400 Clamp 2
26 9291 021 0140 Washer 6.4 2
27 9022 341 1350 Spline screw IS-M6x25 2
28 0781 120 1110 Gear lubricant 225 g option 1
40 0000 958 0600 Washer 1
41 4118 790 7500 Tommy screw 1
42 9022 341 1260 Spline screw IS-M6x12 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FR 108

FR 108: pivot mounting, controls and drive geometry

Flexible connection and six-bushing rigid drive are distinct; tool mounting is M 10 x 1 left-hand thread.

  • Handle adjusts along the shaft for operating position. Anti-vibration elements lie between engine and support frame; pivot-mounted engine follows drive-tube movements to reduce loads on the flexible drive shaft. Source describes AV system and controls as on FR 106, without establishing all-part interchange.
  • Control illustration 360 TI 002: throttle trigger lock (4), throttle trigger (5), slide control (6). Starting throttle, run and stop positions are selected one-handed. Claimed handling, safety and fatigue benefits are source descriptions, not independently measured results.
  • Clutch has lined shoes pivot-mounted on the flywheel. Rigid drive shaft is supported by SIX bushings; do not confuse it with the flexible engine connection. Gearhead is described as same as FS 66 through 108 and FR 106, but the TI supplies no universal parts substitution roster for that range.
  • Cutting-tool mounting (page 4 key 7) is M 10 x 1 LEFT-HAND thread, described as on FS 74,76,86,88,106,108 and FR 106. Gearhead is a helical bevel drive with printed ratio 1.33. Source lists engine speed 12,000 rpm separately from maximum output-shaft/tool-mounting speed 9,000 rpm; they are not interchangeable limits.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 1 · TI 4/1995, p. 3 · TI 4/1995, p. 4 · TI 4/1995, p. 5 — pivot mounting, controls and drive geometry.

No additional parts-table entry added.

Service note · FR 108

FR 108: transport guards and separate lubricants

Transport covers are not operating deflectors; rigid-shaft grease 1109 and gearhead lubricant 1117 stay distinct.

  • Transport guard 4119 790 3906 is listed for cutting blades 230-4/230-8 and brush knife 250-3. Guard 4119 790 3901 is for circular saw blade 200, scratcher or chisel tooth. These are transport guards, NOT the mandatory operating deflector or saw limit stop. Later FR 108 sheet O lists the same numbers with 255/225 mm guard descriptions; those guard diameters are not replacements for the blade-size names.
  • STIHL multipurpose grease 0781 120 1109,80 g (3 oz) tube, is for the RIGID DRIVE SHAFT IN TUBE. STIHL gear lubricant 0781 120 1117,80 g (3 oz) tube, is for the GEARHEAD and also appears in section 4.2. Do not merge their applications or extend the rigid-shaft instruction to the flexible shaft.
  • Later FR 108 sheet K lists 0781 120 1110 as 225 g gear lubricant, whereas this TI names 0781 120 1109 multipurpose grease. These edition/package descriptions are retained without inventing a supersession, chemical equivalence or starter-rope replacement from unrelated catalog annotations.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 5 · TI 4/1995, p. 7 — transport guards and separate lubricants.

Part numbers (4)
  • 4119 790 3906 — Transport guard230-4/230-8 and 250-3 tools · FR 108; TI 04/1995 conditions
  • 4119 790 3901 — Transport guard200 scratcher/chisel circular saw blades · FR 108; TI 04/1995 conditions
  • 0781 120 1109 — Multipurpose grease;80 grigid shaft in tube · FR 108; TI 04/1995 conditions
  • 0781 120 1117 — Gear lubricant;80 ggearhead · FR 108; TI 04/1995 conditions

Service note · FR 108

FR 108: handle, drive and support-frame torques

Gearhead clamps print 8.0 Nm without an imperial value; M4/M5 defaults do not override specific rows.

  • All pairs are printed Nm / lbf.ft; spline screws unless otherwise named. Shroud, IS-M 5x12: 5.5 / 4.0. Two halves of control handle, IS-P 4x19: 2.0 / 1.5. Guard to handle molding, IS-P 4x35: 2.0 / 1.5. Clamp on control handle, IS-M 5x16: 3.5 / 2.6.
  • Clamp screw in drive-tube sleeve, IS-M 6x25: 7.0 / 5.2. Setscrew in drive-tube sleeve, IS-M 5x10: 3.5 / 2.6. Clamp screws in gearhead, IS-M 5x20: 8.0 Nm; imperial cell is BLANK in the scan, not zero or a printed conversion.
  • Bracket to support frame, IS-M 5x10: 3.5 / 2.6. Clamp to support frame, IS-M 5x10: 3.5 / 2.6. Bearing housing to support frame, IS-M 6x12: 10.0 / 7.4. Shackle to support frame, IS-M 6x12: 7.0 / 5.2. Rubber buffer, hexagon nut M6: 5.0 / 3.7.
  • Engine mounting, hex-head M10x20: 30.0 / 22.0. Clamp for loop handle AND strain relief cord, IS-M 6x12: 6.0 / 4.4. Grease filler opening in gearhead, screw plug IS-M 11x10: 10.0 / 7.4.
  • Screws/nuts M4, ALL OTHERS: 2.5 / 1.8. Screws/nuts M5, ALL OTHERS: 4.5 / 3.3. These residual rows are not universal torque values and do not replace listed component values or the two explicit unspecified tensioner rows. No sequence or complete installation procedure is provided.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 8 — handle, drive and support-frame torques.

No additional parts-table entry added.

Conditional replacement · FR 108

FR 108: three rows preserve production and regional differences

Original and new handle assignments retain production, replacement and variant restrictions.

  • FR 108 (source series 4135), older-machine replacement: former handle 4 → forms 6 OR 7, –/X, remarks 1, 2 and 6, with handle 7 RECOMMENDED.
  • Separate production/replacement row: former handle 4 → handle 7 ONLY, X/X, remark 1. Separate Southeast Asia row: former form 8 → handle 6, X/X, remarks 1 and 5. Do not collapse these three rows into universal barrier-handle fitment.
  • All three rows retain the tube part number with a new instruction label. Former handle 4 (4132 790 1310) is old-stock-only; former handle hose/form 8 (4114 791 2002) remains available as spare.
  • Page 5 A refers to the handle figure on page 4 AND the matching item in section 6; B is a drive-tube item number, not a diameter or complete assembly part number. X/X means standard production AND replacement; –/X means replacement only. Blank tube-number cells with remark 1 mean new instruction label with the SAME tube number, not removal of the tube.
  • New handle 6 is 4130 790 1316. Handle 7 is NOT available as a separate item: use handle 6 plus barrier bar 30 (4130 791 4400). Neither assembly choice alone authorizes a cutting tool: the page 2 blade/barrier/universal-deflector restrictions still apply.
  • The printed source is December 21, 1995; introduction is in progress with mixed inventories, not a serial cutoff or proof of installed revision. Catalog title says New Zealand only while the printed matrix includes Southeast Asia; territory discrepancy retained. Historical TI 39/1995 guidance, not current stock or verified physical interchange. No hardware operation was performed.
  • Exact-model IPL navigation only; shared-sheet companion models are NOT added to the source assignment. Printed source series identifiers are retained separately from catalog navigation series.

Source: TI 39/1995, p. 4 · TI 39/1995, p. 5 · TI 39/1995, p. 6 · TI 39/1995, p. 7 · TI 39/1995, p. 8 — Section 5, FR 108: three rows preserve production and regional differences; section 6 row/remark joins.

Part numbers (4)
  • 4132 790 1310 — Former handle 4Source matrix/table component; restrictions in conditions · FR 108: three rows preserve production and regional differences
  • 4114 791 2002 — Former handle hose/form 8Source matrix/table component; restrictions in conditions · FR 108: three rows preserve production and regional differences
  • 4130 790 1316 — New loop handle 6Source matrix/table component; restrictions in conditions · FR 108: three rows preserve production and regional differences
  • 4130 791 4400 — Barrier bar 30; combine with handle 6 for form 7Source matrix/table component; restrictions in conditions · FR 108: three rows preserve production and regional differences

Wrong number or missing part for the FR 108? Report a correction →