Stihl 4135 · Section O · 14 of 20 · 38 parts
Carburetor SK8, SK8-7XA, SK10, SK10-7XA
Fits FR 125, FR 135, FR 145.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (38)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4135 121 5471 | Valve jet | 1 |
| 2 | 4116 121 5100 | Inlet needle | 1 |
| 3 | 1120 122 3004 | Spring | 1 |
| 4 | 1120 121 9200 | Spindle | 1 |
| 5 | 1125 121 5000 | Inlet control lever | 1 |
| 6 | 1120 122 6600 | Collar screw | 1 |
| 7 | 1123 121 0700 | Cup plug | 1 |
| 8 | 4135 129 0972 | Gasket | 1 |
| 9 | 1123 121 4700 | Metering diaphragm | 1 |
| 10 | 1123 121 0801 | End cover | 1 |
| 11 | 4132 122 6600 | Collar screw | 2 |
| 12 | 1120 122 3005 | Spring | 2 |
| 13 | 4135 122 6770 | High speed adjustment screw | 1 |
| 14 | 4135 122 6870 | Low speed adjustment screw | 1 |
| 15 | 1123 122 3000 | Spring | 1 |
| 16 | 4135 120 7170 | Throttle shaft with lever | 1 |
| 17 | 1125 122 9001 | E-clip | 1 |
| 18 | 4135 121 8970 | Pin | 1 |
| 19 | 1120 122 9000 | E-clip | 1 |
| 20 | 4135 121 3370 | Throttle shutter | 1 |
| 21 | 1120 122 7400 | Round head screw | 1 |
| 22 | 1120 121 7800 | Strainer | 1 |
| 23 | 4135 121 4870 | Pump diaphragm | 1 |
| 24 | 4135 129 0973 | Gasket | 1 |
| 25 | 4135 120 2270 | Flange | 1 |
| 26 | 1125 122 4200 | Clamp | 1 |
| 27 | 4135 122 6270 | Idle speed adjustment screw | 1 |
| 28 | 4226 121 2700 | Cap | 1 |
| 29 | 4135 121 0870 | End cover | 1 |
| 30 | 9991 120 0670 | Screw M4x15 | 2 |
| 31 | 4113 121 5471 | Valve jet | 1 |
| 32 | 4113 122 6870 | Low speed adjustment screw | 1 |
| 33 | 4113 129 0972 | Gasket | 1 |
| 34 | 4113 121 2770 | Cap | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4135 120 0671 | Carburetor SK8 | 1 |
| — | 4135 120 0670 | Carburetor SK8-7XA no longer available from factory | 1 |
| — | 4113 120 0671 | Carburetor SK10 | 1 |
| — | 4113 120 0670 | Carburetor SK10-7XA no longer available from factory | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FR 125 / FR 135 / FR 145
FR 125 / FR 135 / FR 145: carburetor settings, clutch speeds and plugs
Common idle and clutch ranges do not make the FR125-only cut-off rating universal.
- Section 2.1.2 specifies an all-position diaphragm carburetor with integral fuel pump. For FR 125 and the FR 135/145 column, both L and H standard settings are open 1 full turn; idle is 2,700–3,000 rpm. These are historical standard settings, not a complete adjustment or loaded-running procedure.
- Only FR 125 has a rated control-valve cut-off of 10,000 rpm without cutting tool. The FR 135/145 entry is a dash: no cut-off speed is supplied for them. Do not read the dash as zero, no speed limit, or permission to use the FR 125 value.
- All three clutches engage at 3,300–3,700 rpm. This engagement range is distinct from idle, power rating and cut-off. The TI gives no test setup or repair tolerances.
- Section 2.1.3 lists suppressed spark plugs NGK BPMR 7 A, Bosch WSR 6F or Champion RCJ 6Y. No electrode gap, tightening torque or STIHL order number is printed. Exact-model ignition/clutch sheets are linked without turning catalog part numbers into TI specifications.
- Historical TI15/1999 names FR 125, FR 135 and FR 145 and series 4126, 4135, 4113. The retained exact-model IPL groups these machines under 4135; that navigation grouping is not a series-equivalence or parts-interchange claim. No serial cutoff or later-model applicability is supplied.
Source: TI 15/1999, p. 1 · TI 15/1999, p. 2 · TI 15/1999, p. 3 · TI 15/1999, p. 4 — All four original pages; contents and figures, sections 1–6, complete specification and accessory tables, repair dependencies and colophons.
No additional parts-table entry added.
Wrong number or missing part for the FR 125, FR 135, FR 145? Report a correction →