← FR 125, FR 135, FR 145 · FS 108 · FR 108

Stihl 4135 · Section P · 15 of 20 · 24 parts

Support frame

Fits FR 125, FR 135, FR 145.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11010101112131415151616181819220212234556788999
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (24)

PosPart numberDescriptionQty
1 4135 790 1870 Support frame 1
2 4135 791 5470 Support 2
3 4135 791 7470 Strap 2
4 4135 701 1870 Backplate 1
5 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 6
6 4135 790 4570 Engine mounting 1
7 4135 708 0870 Spring 3
8 9291 021 0140 Washer 6.4 6
8 9291 021 0140 Washer 6.4 3
9 9022 341 1260 Spline screw IS-M6x12 8
9 9022 341 1260 Spline screw IS-M6x12 9
10 9220 260 0900 Hexagon nut M6 8
10 9220 260 0900 Hexagon nut M6 6
11 9503 003 6540 Grooved ball bearing 6202-2Z 1
12 9503 003 6560 Grooved ball bearing 6202-2Z 1
13 4135 791 1070 Bearing housing 1
14 4135 791 7070 Axle 1
15 4135 791 8370 Hexagon nut M10 2
16 9022 341 1300 Spline screw IS-M6x20 2
18 9210 319 0900 Hexagon nut M6 2
19 4126 792 4570 Engine mounting 1
20 4135 792 4570 Engine mounting 1
21 4113 792 4570 Engine mounting 1
22 4135 710 9070 Harness 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FR 125 / FR 135 / FR 145

FR 125 / FR 135 / FR 145: backpack construction and drive layout

A flexible shaft connects the backpack powerhead to a straight tube containing a rigid shaft.

  • The cover identifies all three backpack brushcutters and illustrates each separately. Intended primary uses are weeds, grass, scrub and shrubs. Favorable power-to-weight ratio, ergonomic controls and comfort are source descriptions, not measured project results.
  • Section 1 describes a torsionally rigid three-part pressed crankshaft supported in bearings at both ends; a large cylinder cooling area; an air filter with improved material, longer life and a large effective surface; and a dual-chamber muffler. No component dimensions, replacement numbers or interchange are established by those descriptions.
  • The carburetor has H, L and LA adjusting screws. A manual fuel pump assists starting; ElastoStart is a special option, not standard equipment. Controls are a throttle/speed-setting lever and stop button. Clutch shoes are lined.
  • The flexible shaft is supported in a protective liner. The rigid shaft in the straight drive tube is supported in ball bearings. The AV system uses three spring-supported points; this is not a rigid/flexible-shaft substitution or spring specification.
  • Historical TI15/1999 names FR 125, FR 135 and FR 145 and series 4126, 4135, 4113. The retained exact-model IPL groups these machines under 4135; that navigation grouping is not a series-equivalence or parts-interchange claim. No serial cutoff or later-model applicability is supplied.

Source: TI 15/1999, p. 1 · TI 15/1999, p. 2 · TI 15/1999, p. 3 · TI 15/1999, p. 4 — All four original pages; contents and figures, sections 1–6, complete specification and accessory tables, repair dependencies and colophons.

No additional parts-table entry added.

Service note · FR 125 / FR 135 / FR 145

FR 125 / FR 135 / FR 145: repair-document boundaries

The announced model shop manual excludes carburetor service, troubleshooting and standard repairs.

  • Section 5 requires strict observance of local and national safety regulations and the owner’s-manual precautions whenever a unit is started during repairs or maintenance. This reference review is not an instruction to run a machine unattended.
  • Section 5.1 says a separate FR 125/135/145 shop manual will be available in the near future. It excludes Servicing the Carburetor, Troubleshooting and repairs involving standard procedures; those are delegated to Carburetors and Standard Repairs, Troubleshooting handbooks. The TI is not a complete repair manual.
  • The exact announced model shop manual and contemporaneous handbook/owner’s-manual editions have not been established in the checked retained sources. Exact-model catalog/document joins lead to this TI and the IPL, not an FR 125/135/145 workshop manual. The workshop-title inventory and local service-manual filename inventory do not establish those editions; later FR 350/450 material is not a substitute.
  • Section 6 says an illustrated parts list is available. The retained 01-2012 exact-model IPL provides assembly navigation, not proof of an identical 1999 edition. Its differing starter ropes remain explicit conflicts. Missing repair dependencies stay gaps; no repair steps are fabricated.
  • Historical TI15/1999 names FR 125, FR 135 and FR 145 and series 4126, 4135, 4113. The retained exact-model IPL groups these machines under 4135; that navigation grouping is not a series-equivalence or parts-interchange claim. No serial cutoff or later-model applicability is supplied.

Source: TI 15/1999, p. 1 · TI 15/1999, p. 2 · TI 15/1999, p. 3 · TI 15/1999, p. 4 — All four original pages; contents and figures, sections 1–6, complete specification and accessory tables, repair dependencies and colophons.

No additional parts-table entry added.

Wrong number or missing part for the FR 125, FR 135, FR 145? Report a correction →