← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section Q · 16 of 17 · 14 parts

Blade drive gear 0° - 90° (24.2005)

Fits FH 75.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011111213142233445566789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (14)

PosPart numberDescriptionQty
1 4230 640 0501 Gear housing 1
2 9513 003 0912 Needle cage 8x12x8 2
3 4226 641 6500 Screw plug 2
4 9381 003 2070 Cylindrical pin 4x12 2
5 4230 642 4800 Thrust plate 2
6 4230 642 6501 Connecting rod 2
7 4230 640 7501 Spur gear 1
8 4226 649 0301 Gasket 1
9 4230 649 0300 Gasket 1
10 4230 640 5801 Gearbox cover 1
11 9022 313 0680 Spline screw IS-M4x16 10
12 4230 641 6600 Guard plate 1
13 0000 967 3730 Warning pictogram 1
14 0781 120 1109 Gear lubricant 80 g option 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FH 75

FH 75: underside guard plate and its own screw torque

The guard plate protects the gearbox underside; its IS-M4x16 screw joint is specified at 3.5 Nm (2.6 lbf.ft).

  • The blade-drive gear follows the HL 75 construction but has a guard plate screwed to the gearbox cover to protect the underside of the housing. Figure 225TI001 KN item1 identifies this plate, not the nose guard at item2.
  • The only torque row here is spline screw IS-M4x16, guard plate/gearbox cover, 3.5 Nm (2.6 lbf.ft). It is not a general torque for every M4 screw or the entire blade drive. The TI gives no screw or guard-plate order number.
  • The later exact FH 75 0–90-degree blade-drive sheet lists the guard plate and IS-M4x16 screws. Its dated 24/2005 sheet label and additional numbers are not silently backdated to the 1998 introduction; no number is promoted from that catalog into this TI record.
  • If the machine is started during repairs or maintenance, the TI requires all local safety regulations and the owner’s-manual precautions. The applicable owner manual remains an actionable dependency; this torque note is not permission to run a machine.
  • TI 47/1998 names the FH 75 power scythe, printed series 4230. The retained 01-2012 exact FH 75 sheets are under catalog series 4137: these are model-label navigation links, not proof that the series identifiers or every later configuration are equivalent. No extension to FH attachments, FH-KM or later 135-degree heads, serial cutoff, retrofit or tested physical interchange is established.

Source: TI 47/1998, p. 2 · TI 47/1998, p. 3 — Page2 section1 blade-drive-gear paragraph and figure225TI001 KN item1; page3 section6 safety preamble and complete6.1 torque row.

No additional parts-table entry added.

Wrong number or missing part for the FH 75? Report a correction →