← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section R · 17 of 17 · 27 parts

Drive tube assembly, Blade

Fits FH 75.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131314151516161718191922021222324252634456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (27)

PosPart numberDescriptionQty
1 4230 710 7103 Drive tube assembly Ø 25.4 mm / 1" 1
2 4230 710 7101 Drive tube assembly Ø 25.4 mm / 1" 1
3 4137 711 7300 Flexible liner 1455 mm / 57 5/16'' 1
4 4137 711 2101 Plug 2
5 0000 967 3728 Warning pictogram HL 1
6 0000 967 3739 Warning pictogram HL 1
7 4230 791 2001 Handle hose 270 mm / 10 5/8'' 1
8 4137 711 3200 Drive shaft → replaced by 4137 711 3202 TI 11/2005 1
9 0000 711 2500 Sleeve 1
10 4230 790 8801 Loop 1
11 0000 951 1104 Screw IS-M5x22 1
12 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 2
13 4230 641 4615 Guide 2
14 4230 713 1715 Flat spring 1
15 4230 710 6052 Blade 1
16 4226 713 6600 Pin 2
17 4226 648 6701 Slider 5
18 9022 341 0980 Spline screw IS-M5x16 3
19 9220 263 0702 Hexagon nut M5 3
20 4230 790 9800 NLA Guide guard 1
21 4230 792 9000 NLA Guide guard 1
22 4230 790 9201 Blade guard 1
23 4130 710 9000 Harness option 1
24 4128 890 3400 Combination wrench 1
25 0000 890 2300 NLA Screwdriver 1
26 0000 891 0801 NLA Tool roll option 1
Not numbered on the diagram — assemblies, kits and options
— 4230 710 6020 Blade 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FH 75

FH 75: nine-position power scythe and HL 75 differences

The 1998 FH 75 has a 0–90-degree cutter bar and a 250 mm cutting length; shared construction is not a universal interchange rule.

  • The FH 75 is described for scrub, thicket, wild growth and grass in busy areas such as traffic islands, roadsides, parking lots, parks and playgrounds. It is held like a brushcutter and swung side to side in an arc close to the ground. This is the historical intended use, not a complete operating or safety procedure.
  • The cutter bar has nine positions between 0 and 90 degrees. Page1 contrasts its 250 mm (10 in) cutter bar with the HL 75’s 550 mm (22 in) version. The photograph shows the complete machine and an inset of head positions; it supplies no additional part numbers.
  • Section1 names the engine, shaft, control handle, loop handle, angle drive and blade-drive gear construction as the same as the HL 75 0–90-degree version. The shorter cutting bar, underside guard plate and nose guard remain explicit differences. This comparison does not authorize replacing the whole FH head with an HL head.
  • Overall length is approximately 178 cm (70 in) with the cutter bar at 90 degrees and approximately 215 cm (84.6 in) with it straight at 0 degrees. Dry weight WITH blade guard is 6.5 kg (14.3 lb). Do not relabel that weight as bare-machine or operating weight.
  • TI 47/1998 names the FH 75 power scythe, printed series 4230. The retained 01-2012 exact FH 75 sheets are under catalog series 4137: these are model-label navigation links, not proof that the series identifiers or every later configuration are equivalent. No extension to FH attachments, FH-KM or later 135-degree heads, serial cutoff, retrofit or tested physical interchange is established.

Source: TI 47/1998, p. 1 · TI 47/1998, p. 2 · TI 47/1998, p. 3 — Complete page1 introduction and overview photograph; page2 operating description and section1 common construction; page3 sections2.1–3.

No additional parts-table entry added.

Service note · FH 75

FH 75: cutting length, blade length and sharpening aids

Keep the 250 mm cutting length separate from the 300 mm blade length and the 45-degree sharpening angle.

  • The cutting blades are bidirectional, with a 45-degree sharpening angle. Cutting length is 250 mm (10 in); blade length is 300 mm (12 in). These are distinct dimensions, not conflicting measurements to normalize.
  • The FH 75 has a nose guard, figure225TI001 KN item2, intended to help reduce the risk of damaging the blades. It is distinct from the underside gearbox guard plate and from the blade guard included in the dry-weight condition. No nose-guard number or full sharpening procedure is supplied.
  • Flat sharpening file 0814 212 3310 is listed for sharpening the cutting blades. Spray cleaner 0782 420 1002 is listed for cleaning them. The cleaner is not identified as gearbox grease, and the file listing alone does not establish a current replacement product.
  • The later exact FH 75 drive-tube/blade sheet is only the navigation target. Its blade and guide-guard numbers do not supply missing original 1998 order numbers or prove every later blade has these dimensions.
  • TI 47/1998 names the FH 75 power scythe, printed series 4230. The retained 01-2012 exact FH 75 sheets are under catalog series 4137: these are model-label navigation links, not proof that the series identifiers or every later configuration are equivalent. No extension to FH attachments, FH-KM or later 135-degree heads, serial cutoff, retrofit or tested physical interchange is established.

Source: TI 47/1998, p. 2 · TI 47/1998, p. 3 — Page2 cutting-blades paragraph and225TI001 KN item2; page3 sections3–4 in full.

Part numbers (2)
  • 0814 212 3310 — Flat sharpening fileUser accessory for sharpening cutting blades · FH 75; TI 47/1998 application only
  • 0782 420 1002 — Spray cleanerUser accessory for cleaning cutting blades · FH 75; TI 47/1998 application only

Service note · FH 75

FH 75: service and repair-time references retain their scope

The TI points to named HL/FS/HS tools, the combined service manual and HL 75 repair times; those references are not a complete FH 75 procedure.

  • Section 5.1 says the same special servicing tools are used as for HL 75, FS 75, FS 80, FS 85, HS 75, HS 80 and HS 85. It does not list individual tool numbers or state that every procedure or part from those machines fits the FH 75.
  • Section6 says setting and testing data and other information are the same as HL 75 and FS 75/80/85. HS models occur in the tool reference, not this sentence. Companion notes distinguish separately dated 2004 engine/ignition/fuel tables and detailed diagnostic and adjustment variants; the exact original 1998 reference edition remains a bounded source gap.
  • Section6.2 refers to the FS 75/80/85,FC 75,HL 75 service manual for FH 75 repairs. Later split editions have verified FH 75 scope; enumerated head, torque, tool, aid, diagnostic and carburetor-adjustment sections are separately admitted. The TI 32/1994 ignition reference is reconciled without erasing differing settings or labels. Original combined and operator editions remain bounded source gaps, not substitutes supplied by those later manuals.
  • Section 6.3 says FH 75 repair times are exactly the same as HL 75 in TI 41/1996 and the STIHL repair-times table. The companion FH 75 labor notes now admit the explicit 20-row TI transfer and separately dated 2012 exact-model table, preserving changed codes, units, inclusions, four blanks and the printed zero. The original parent timetable remains a bounded source gap; this is not parts interchange.
  • The page 4 imprint identifies 1998 Andreas Stihl AG & Co., Waiblingen, Technical Documentation D1/MTK-sc,6459. It supplies no additional part assignment. No whole manual is imported or reviewed by adding this reference note.
  • TI 47/1998 names the FH 75 power scythe, printed series 4230. The retained 01-2012 exact FH 75 sheets are under catalog series 4137: these are model-label navigation links, not proof that the series identifiers or every later configuration are equivalent. No extension to FH attachments, FH-KM or later 135-degree heads, serial cutoff, retrofit or tested physical interchange is established.

Source: TI 47/1998, p. 3 · TI 47/1998, p. 4 — Page 3 sections 5.1 and 6 preamble; page 4 sections 6.2–6.3 and imprint in full.

No additional parts-table entry added.

Wrong number or missing part for the FH 75? Report a correction →