Stihl 4137 · Section C · 3 of 21 · 16 parts
Ignition system, Clutch
Fits FR 85 T, FR 85.
Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.
Parts (16)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4137 400 1200 | Flywheel Fitment / change note → | 1 |
| 2 | 4137 400 1350 | Ignition module | 1 |
| 3 | 4137 442 0400 | Insulating hose | 1 |
| 4 | 1106 405 1000 | Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 | 1 |
| 5 | 0000 998 0606 | Torsion spring | 1 |
| 6 | 4137 405 1600 | Plug connector | 1 |
| 7 | 4137 404 9300 | Washer | 2 |
| 8 | 9022 371 0710 | Spline screw IS-M4x20 | 2 |
| 9 | 4137 160 2001 | Clutch | 1 |
| 10 | 1129 162 0800 | Clutch shoe | 3 |
| 11 | 1127 162 3000 | Retainer | 3 |
| 12 | 0000 997 5625 | Tension spring | 3 |
| 13 | 1121 162 3000 | Retainer | 3 |
| 14 | 9022 341 0980 | Spline screw IS-M5x16 | 2 |
| 15 | 4137 080 1606 | Shroud | 1 |
| 16 | 4137 967 1508 | Model plate FR 85 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · FS 75 / FS 80 / FS 85 / FR 85 / FC 75
FS 75 / FS 80 / FS 85 / FR 85 / FC 75: series 4137 replacement ignition assignment
4137 400 1307 with flywheel 4137 400 1200; ignition lead not replaceable.
- Printed series 4137. Use 4137 400 1307 with flywheel 4137 400 1200.
- The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.
Part numbers (2)
- 4137 400 1307 — Replacement ignition moduleAssigned component · FS 75 / FS 80 / FS 85 / FR 85 / FC 75, printed series 4137, listed combination only
- 4137 400 1200 — Assigned flywheelRequired pairing · FS 75 / FS 80 / FS 85 / FR 85 / FC 75, printed series 4137
Service note · FR 85
FR 85: engine, speed and ignition specifications
Keep clutch, idle, electronic cutoff and rated output-shaft speeds distinct.
- Engine: displacement 25.4 cm³ (1.55 cu.in), bore 34 mm (1.34 in), stroke 28 mm (1.10 in); power 0.9 kW (1.2 bhp) to ISO 8893. Rewind starter uses a SINGLE pawl and ElastoStart grip; starter-rope reference points to section 4. Fuel tank 0.44 l (0.92 US pt). These are the printed historical specifications, not measured values for a connected machine.
- Clutch engages at 3700 rpm; idle speed is 2800 rpm. Electronic CUT-OFF RANGE WITHOUT CUTTING TOOL is 9700–11300 rpm. Maximum OUTPUT SHAFT speed (rated) is 7500 rpm. Do not treat output-shaft speed as an engine-speed setting, the cutoff range as an operating target with a blade, or clutch engagement as idle.
- All-position diaphragm carburetor includes integral fuel pump. Standard L setting: OPEN ONE FULL TURN. Section 1 names L and LA only; no H-screw setting is supplied. Section 6.1 separately delegates carburetor adjustment to TI41/1997: this specification is not a complete adjustment/run-up procedure. No engine was started.
- Ignition module includes an electronic speed limiter. SUPPRESSED spark plugs named: Bosch WSR 6F, NGK BPMR 7 A or Champion RCJ 6Y. No plug gap or ignition air gap is stated here; none is inferred. Gear ratio is printed simply as 1.4, without a new tooth-count claim.
- Weight is 9.4 kg (20.7 lb) WITHOUT CUTTING TOOL AND DEFLECTOR. No fuel-fill qualifier is printed in this weight line; do not silently label it dry, fueled or ready-to-cut weight. Later catalog assemblies remain references, not a reconstruction of every 1998 build.
- Historical FR 85, series 4137, as described in TI34/1998. Shared FR 85 T catalog sheets do not extend this note to FR 85 T or other variants. No hardware operation was performed; no physical interchange test or current stock claim.
Source: TI 34/1998, p. 3 · TI 34/1998, p. 4 — Sections 2.1–2.3: complete mechanical, fuel, ignition, gearhead and weight specifications; acoustic table in companion note.
No additional parts-table entry added.
Service note · FR 85
FR 85: spark-plug boot spring and two different gaps
The later powerhead reference separates the 0.5 mm electrode gap from the 0.2–0.5 mm ignition air gap.
- Later-manual comparison following TI 34/1998 sections 5.1, 6.2 and 6.3, not proof of the exact manuals available in 1998. The TI delegates POWERHEAD work to FS 75/80/85 literature and SHAFT/SUPPORT FRAME work to FR 350/450 literature. Later values and tooling require a matching component/configuration; they are not blanket FR 85 or FR 85 T repair settings.
- Series4137 Powerhead edition2004-03 section3.2 lists electronic magneto ignition with integrated switch gear, an AIR GAP of 0.2–0.5 mm, and a SPARK-PLUG ELECTRODE GAP of 0.5 mm. Suppressed plugs are Bosch WSR6F, NGK BPMR7A and Champion RCJ6Y. The gaps come from this LATER manual, not TI34/1998, whose specifications omit them. They are different physical clearances, not interchangeable settings or proof for every FR85 revision.
- Chapter6 describes a capacitive breakerless system comprising module and flywheel and says to begin troubleshooting at the spark plug. It warns that high ignition voltages can cause serious or fatal injury. Section4.2 lists rough running/misfire/temporary power loss leads: loose boot (seat firmly, new leg spring if necessary), sooted/oily plug (clean or replace), weak/no spark (insulation or broken/high-resistance lead), incorrect air gap, damaged flywheel, damaged slide control/coil/wire insulation and leakage current. No-spark also requires checking slide control, module and leads. These are alternative diagnostic leads, not observed faults.
- Section6.1 removes the shroud using the Components manual, unplugs the boot, pulls out the leg spring with suitable pliers, unhooks it from the ignition lead and removes the boot. Coat about 20 mm of the lead end with oil, refit the boot and pull the lead through with pliers. Pinch the spring HOOK INTO THE CENTRE OF THE LEAD ABOUT 5 mm FROM ITS END (935RA073), then pull back until the spring seats inside the boot. No oil grade, conductor-strip length or replacement part number is specified.
- If the spark plug has a detachable adapter nut, it must be properly fitted and firmly tightened before reconnecting the boot and refitting the shroud. This does not provide an adapter-nut torque. The troubleshooting recommendation to replace a lead must be read with6.2.2: the pictured lead is INTEGRALLY MOULDED into the module; a separate lead replacement method is not supplied.
- No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.
TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections 5.1, 6.2 and 6.3: later Series 4137 Powerhead ignition reference.
Later manual evidence: Series 4137 Powerhead (2004-03), section 3.2 complete;4.2 complete;6 introduction;6.1 complete, PDF pages 5, 8, 20, 21
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · FR 85
FR 85: ignition module spacers, ground connection and air-gap gauge
The later module reference preserves optional plastic disks and ground wiring without resolving the printed torque-label conflict.
- Later-manual comparison following TI 34/1998 sections 5.1, 6.2 and 6.3, not proof of the exact manuals available in 1998. The TI delegates POWERHEAD work to FS 75/80/85 literature and SHAFT/SUPPORT FRAME work to FR 350/450 literature. Later values and tooling require a matching component/configuration; they are not blanket FR 85 or FR 85 T repair settings.
- Section6.2 identifies the high-voltage output with ignition lead, connector tab for short-circuit wire, and ground wire IF INSTALLED. Accurate module testing requires special equipment; the workshop spark check is narrower. Replace a no-spark module only AFTER checking that wiring and stop switch are in good condition. Section6.2.1 says ignition timing is NOT ADJUSTABLE; that is not proof that spark presence establishes correct timing or flywheel position.
- Section6.2.2 first removes the starter mechanism, or fan housing with starter mechanism, using the Components reference. Unplug the short-circuit wire; on TWO-WIRE units unplug both from module and terminal socket. Disconnect the spark-plug boot, remove screws WITH WASHERS and remove the module. Dismantle the boot under6.1. The lead is INTEGRALLY MOULDED into the module: do not infer a screw-in lead joint from the generic troubleshooting replacement wording.
- Position the module with screws loose. Secure the GROUND WIRE and CONNECTOR TAB to the UPPER SCREW if installed (935RA082). On older models a PLASTIC DISK may be present on both upper and lower screws BETWEEN CYLINDER AND MODULE; refit it if necessary. No date, FR85 serial cutoff, disk part number, thickness or universal fitment is supplied.
- Slide gauge 4118 890 6401 BETWEEN THE MODULE ARMS AND FLYWHEEL MAGNETIC POLES (935RA083), press the module against it and tighten screws using3.3, then reverse the disassembly. Section3.2 gives0.2–0.5 mm air gap. The existing3.3 conflict remains: the printed IS-M4x20 row says Spark plug/4.5 Nm, while M14x1.25 says Ignition module/Cylinder/20.0 Nm. This note does NOT promote the latter20 Nm to a module-screw setting or silently swap labels. Match an independently verified joint specification before actual assembly.
- No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.
TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections 5.1, 6.2 and 6.3: later Series 4137 Powerhead ignition reference.
Later manual evidence: Series 4137 Powerhead (2004-03), section 6.2,6.2.1,6.2.2 complete;3.2/3.3 and7 item10 prerequisites, PDF pages 5, 6, 21, 22, 23, 29
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · FR 85
FR 85: spark tests do not verify timing or share one ZAT 3 setup
Keep the later 2 mm series-gap procedure separate from the flowchart’s TI32/1994 main-gap reference.
- Later-manual comparison following TI 34/1998 sections 5.1, 6.2 and 6.3, not proof of the exact manuals available in 1998. The TI delegates POWERHEAD work to FS 75/80/85 literature and SHAFT/SUPPORT FRAME work to FR 350/450 literature. Later values and tooling require a matching component/configuration; they are not blanket FR 85 or FR 85 T repair settings.
- Section6.2.3 names ZAT4 5910 850 4503 and ZAT3 5910 850 4520. It explicitly limits the test to SPARK, NOT IGNITION TIMING. For ZAT4 it installs a NEW SPARK PLUG in the cylinder, connects the boot to tester input(1), output(3) to the plug, cranks with the rewind starter at MINIMUM 1,000 rpm and observes window(2). A visible spark is the manual criterion; unclear results lead to ZAT3 or6.4, not automatic module condemnation. The source refers plug tightening to the already-conflicted3.3 table; this is not a new torque determination.
- The6.2.3 ZAT3 SERIES-GAP setup also retains a new plug in the cylinder: boot to terminal(2), ground clip/terminal(1) TO THE SPARK PLUG, gap about2 mm using knob(3), crank at minimum1,000 rpm and observe window(3). Hold ONLY handle(4) or position safely; keep fingers/body at least1 cm from spark window(3), high-voltage connection(2), ground connection(5) and ground terminal(1). The text uses(3) for both knob and window; retain the depicted distinction, not a new pinout.
- The6.4 flowchart instead explicitly says use ZAT3 as MAIN SPARK GAP and cites TI32.94. The already-reviewed TI32/1994 specifies6 mm with plug REMOVED and clip on ENGINE GROUND for main-gap mode, versus2 mm with clip on the installed PLUG for auxiliary mode. These are DISTINCT CONFIGURATIONS, not two interchangeable values for one connection. The later manual does not reconcile its series-gap procedure and flowchart wording; do not blend them into a hybrid test.
- TI32/1994 shared precautions remain: no use near flammable fuel/gas, with wet hands or by uninstructed persons/children; hold the knurled handle, maintain1 cm separation, do not force the gap knob past its stop. Its auxiliary arrangement can START THE ENGINE during cranking and requires the tool owner-safety instructions. Its bright-light advice is to blacken one side of the window or use a dark background. This is retained source context, not bench authorization.
- If no spark is visible,6.2.3 checks harness and start-stop switch/slide control via Components, examines the leg spring under6.1 and follows6.4. Visible spark is NOT a full module/timing/load-performance certificate. No cranking, spark generation or ignition actuation was performed.
- No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.
TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections 5.1, 6.2 and 6.3: later Series 4137 Powerhead ignition reference.
Referenced bulletin evidence: TI 32/1994, p. 1 · TI 32/1994, p. 2 — Main and auxiliary ZAT3 configurations; shared precautions.
Later manual evidence: Series 4137 Powerhead (2004-03), section 6.2.3 complete;6.4 main-gap cross-reference;7 items26–27;3.3 conflict context, PDF pages 6, 20, 21, 23, 24, 26, 30
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · FR 85
FR 85: flywheel inspection, puller and clean mating surfaces
The later reference requires undamaged magnetic poles and preserves the flywheel groove orientation.
- Later-manual comparison following TI 34/1998 sections 5.1, 6.2 and 6.3, not proof of the exact manuals available in 1998. The TI delegates POWERHEAD work to FS 75/80/85 literature and SHAFT/SUPPORT FRAME work to FR 350/450 literature. Later values and tooling require a matching component/configuration; they are not blanket FR 85 or FR 85 T repair settings.
- Section6.3 first dismantles the clutch using the Components manual. Pull the flywheel off by hand; if it cannot be removed by hand, screw on puller 4133 893 0800, TAP THE FACE OF THE PULLER LIGHTLY and remove it (935RA086–088). This is the illustrated puller method, not permission to strike magnetic poles or use a jaw puller.
- There must be NO SIGN OF DAMAGE on the flywheel or MAGNETIC POLES (935RA089), otherwise replace the flywheel. The6.4 flowchart additionally flags BLUE POLE SHOES; that diagnostic is retained in the companion flowchart note. No flywheel replacement number, key dimensions or model interchange is specified here.
- Degrease the CRANKSHAFT STUB and FLYWHEEL HUB BORE with STIHL degreasant under8 item2. That row supplies no part number, substitute or application quantity. Position the flywheel while noting the GROOVE POSITION, reinstall the clutch using Components and reverse the remaining disassembly. No separate flywheel-nut torque is supplied in6.3; the previously reviewed26 Nm clutch setting is not silently renamed a separate nut setting.
- No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.
TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections 5.1, 6.2 and 6.3: later Series 4137 Powerhead ignition reference.
Later manual evidence: Series 4137 Powerhead (2004-03), section 6.3 complete;7 item28;8 item2, PDF pages 24, 25, 30, 31
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · FR 85
FR 85: ignition fault-tree branches and resistance units
Original pages confirm 1.5–12 kΩ boot-to-ground and less than10 Ω lead resistance, not watts.
- Later-manual comparison following TI 34/1998 sections 5.1, 6.2 and 6.3, not proof of the exact manuals available in 1998. The TI delegates POWERHEAD work to FS 75/80/85 literature and SHAFT/SUPPORT FRAME work to FR 350/450 literature. Later values and tooling require a matching component/configuration; they are not blanket FR 85 or FR 85 T repair settings.
- The6.4 no-run chart starts with slide control/separate stop switch in I, then checks plug oil/soot, electrode gap and shorted contacts (clean/reset/replace). Next check boot seating/leg spring, hook in lead centre and boot damage, replacing boot/spring if needed, then test with ZAT3 or ZAT4. Its explicit ZAT3 MAIN-GAP/TI32.94 reference is not the same setup as6.2.3; see the companion test-configuration note.
- FIRST Powerful spark? YES follows connector3 DIRECTLY TO Engine runs? on the final page, bypassing the no-spark repair chain. NO checks/resets air gap, checks for BLUE FLYWHEEL POLE SHOES (replace flywheel), disconnects the module short-circuit wire, then checks severe lead chafing, holes/cracks in the boot and resistance. These arrows were read from the ORIGINAL DIAGRAM, not inferred from extracted-text order.
- The original PDF27 chart specifies SPARK-PLUG BOOT TO GROUND 1.5–12 kΩ and IGNITION LEAD LESS THAN10 Ω. Text extraction renders the omega symbols as W; the original shows OHMS, not watts. The chart provides no temperature, meter type, probe-placement drawing or isolated-module acceptance test. Preserve the named measurement paths rather than treating them as generic coil resistance. Generic boot/lead replacement wording remains in tension with6.2.2 INTEGRALLY MOULDED lead construction; no separate lead repair method is established.
- Connector2 then checks slide control/separate stop switch, short-circuit-wire chafing and contact-spring gap; the box says replace ignition lead and/or contact springs if necessary, then RE-CONNECT THE SHORT-CIRCUIT WIRE. No numeric contact gap is provided. The SECOND Powerful spark? NO leads to a new module; YES joins connector3. Both paths then ask Engine runs? YES requires a RUN/STOP FUNCTION CHECK; NO redirects to fuel system/carburetor, engine leaks and flywheel position on crankshaft. Do not skip reconnection or stop-function verification, or equate spark with a running engine. This is a documented historical flowchart, not an executed test or authorization to disable a stop circuit.
- No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.
TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections 5.1, 6.2 and 6.3: later Series 4137 Powerhead ignition reference.
Later manual evidence: Series 4137 Powerhead (2004-03), section 6.4 complete;3.2/4.2/6.1/6.2.2 construction context, PDF pages 5, 8, 21, 23, 26, 27, 28
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · FR 85
FR 85: FR-specific drum bearing removal and tool-number conflict
The later FR manual removes the bearing separately; its drum tool number differs between procedure and tool list.
- Later FR-specific Components 4137 reference, edition 2005-05, following TI34/1998 sections 5.1, 6.2 and 6.3. This is RA_265, distinct from the previously compared FC–KW manual RA_394 (2004-06) and FR350/450 manual RA_250 (2003-04). Exact 1998 FR85 configuration remains unestablished. Match the actual component and fasteners; these are not blanket FR85 or FR85T repair settings.
- Section5.2.2 first removes the engine via5.2.1. That prerequisite removes the shroud and rewind starter (6.2), then fan-housing screws and the ENGINE WITH TANK. Section5.1 requires the cylinder-side gaskets and ignition lead to locate in the shroud guides on refitting. Existing starter and clutch-shoe notes remain context, not additional work accomplished by drum removal.
- Disconnect the FLEXIBLE SHAFT from the fan housing, remove the support-frame screw shown in936RA330, pry the fan housing out of the frame and remove the drum circlip (936RA333). Section5.2.2 then inserts an EXTENSION 4180 890 4400 in the SQUARE HOLE and presses the drum TOWARDS THE ENGINE on a standard press (936RA334). No pressing load or support dimensions are stated.
- TOOL-NUMBER CONFLICT: section11 item9 instead lists DRIFT 4180 893 4400 for removing the clutch drum. The original pages visibly differ in the middle group, 890 versus893; preserve both rather than silently correcting one or treating them as interchangeable. Tool identity must be resolved for an actual operation.
- If the BALL BEARING is damaged, remove its separate circlip and press the bearing TOWARDS THE ENGINE (936RA335). Install in reverse sequence. This FR-specific construction permits separate bearing removal, unlike the earlier FC–KW comparison that requires the whole fan housing if its bearing is faulty. Neither statement establishes a universal replacement rule, bearing part number, interference fit or an FR85 serial changeover.
- The FR removal prerequisite repeats the drum remaining-wall criterion LESS THAN ABOUT80% of original thickness. This corroborates the already recorded relative threshold; it supplies no absolute millimeter wear limit. Do not transfer the FC–KW installation-drift assignment into this FR procedure, which states only reverse-sequence installation.
- No hardware operation was performed. FR 85 catalog sheets provide context, not proof that every part, fastener or revision matches the later manual. No physical interchange, current stock, universal procedure or complete safety-instruction claim.
TI dependency: TI 34/1998, p. 5 · TI 34/1998, p. 6 — TI sections5.1,6.2,6.3: later FR-specific component comparison.
Later manual evidence: Components 4137 — FR, HLR, HTR (2005-05), section 5.2.2 complete;5.1/5.2.1 removal prerequisites;3.2 selected rows;11 item9, PDF pages 6, 14, 16, 17, 51 · Components 4137 — FC, FH, FS, HL, KM, KW (2004-06), section 5.2.2 complete; 7.1 complete applicability comparison; 11 items 9,10,19,21; 12 item 7, PDF pages 16, 17, 24, 25, 26, 67, 68
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the FR 85 T, FR 85? Report a correction →