← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Assembly · 24 of 25 · 6 parts

AA Transport guard

Fits FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
123456
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (6)

PosPart numberDescriptionQty
1 4116 790 3901 Transport guard Ø 350 1
2 4116 792 4300 Clamping wire 1
3 4119 790 3901 Transport guard Ø 225 Fitment / change note → 1
4 4119 792 4300 Clamping wire 1
5 4119 790 3906 Transport guard Ø 255 Fitment / change note → 1
6 4119 792 4305 Clamping wire 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · FS 80 / FS 80 R / FS 85 / FS 85 R

FS 80 / 85: handle restrictions for metal and circular saw blades

230-4/230-8 blades and 250-3 knife require barrier bar or bike handle; circular saw blades require BIKE HANDLE ONLY.

  • Section 3 footnote 3: cutting blade 230-4 4001 713 3801, cutting blade 230-8 4001 713 3803 and brush knife 250-3 4112 713 4100 are for FS 80/85 ONLY WITH BARRIER BAR OR BIKE HANDLE. A plain loop handle without the barrier bar is not included.
  • Section 3 footnote 4: circular saw blade 200 scratcher tooth 4112 713 4201 and circular saw blade 200 chisel tooth 4112 713 4203 are for FS 80/85 BIKE HANDLE ONLY. Adding a barrier bar to a loop handle does NOT satisfy this circular-saw restriction. None of these five metal-tool rows authorizes FS 75 use.
  • Section 4 transport guard 4119 790 3906 is assigned to 230-4/230-8 blades and 250-3 knife; guard 4119 790 3901 to BOTH 200 circular saw blades. These are TRANSPORT guards, not operating deflectors or permission to omit an operating guard. Later IPL describes the guards by Ø255/Ø225; those diameters do not change the tool-specific 1996 pairing.
  • Scope is the 1996 series 4137 introduction, including depicted R and RB handle arrangements. No scope is inherited by FS 85 T/RX, FC/FR/HL/HT/KM/KW/SP models or later same-named machines from a shared IPL sheet. Historical source guidance, not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 36/1996, p. 1 · TI 36/1996, p. 5 — FS 80 / 85: handle restrictions for metal and circular saw blades.

Part numbers (7)
  • 4001 713 3801 — Cutting blade 230-4; item 91996 approved metal tool with handle restriction · FS 80/85 with barrier bar or bike handle
  • 4001 713 3803 — Cutting blade 230-8; item 101996 approved metal tool with handle restriction · FS 80/85 with barrier bar or bike handle
  • 4112 713 4100 — Brush knife 250-3; item 111996 approved metal tool with handle restriction · FS 80/85 with barrier bar or bike handle
  • 4112 713 4201 — Circular saw blade 200 scratcher tooth; item 121996 approved metal tool with handle restriction · FS 80/85 bike handle ONLY
  • 4112 713 4203 — Circular saw blade 200 chisel tooth; item 131996 approved metal tool with handle restriction · FS 80/85 bike handle ONLY
  • 4119 790 3906 — Transport guardTransport protection; not an operating deflector · 230-4/230-8 blades and 250-3 brush knife
  • 4119 790 3901 — Transport guardTransport protection; not an operating deflector · 200 scratcher/chisel circular saw blades

Wrong number or missing part for the FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX? Report a correction →