← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section L · 11 of 25 · 36 parts

Carburetor C1Q-S28E, C1Q-S41C 1 42 812 153 (21.1999)

Fits FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX.

Parts diagrams →

Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212223242526272829330313233456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (36)

PosPart numberDescriptionQty
1 4226 120 7100 Throttle shaft with lever 1
2 1123 122 3000 Spring 1
3 4227 121 3300 Throttle shutter Fitment / change note → 1
4 1125 122 7403 Round head screw 1
5 1125 122 9001 E-clip 1
6 4128 121 8900 Pin 1
7 1120 122 9000 E-clip 1
8 1129 121 4800 Pump diaphragm 1
9 1123 129 0905 Gasket 1
10 1123 121 0800 End cover Fitment / change note → 1
11 1120 122 7800 Oval head screw 1
12 4116 121 5100 Inlet needle 1
13 1123 122 3001 Spring 1
14 1125 121 5000 Inlet control lever 1
15 1120 121 9200 Spindle 1
16 1120 122 6600 Collar screw 1
17 4129 129 0902 Gasket 1
18 4129 121 4700 Metering diaphragm 1
19 4226 120 2200 Flange 1
20 4226 122 7100 Screw 2
21 4137 122 6800 Low speed adjustment screw Fitment / change note → 1
22 1128 122 7100 Screw 2
23 1120 122 3005 Spring Fitment / change note → 1
24 1123 121 7800 Strainer 1
25 4137 121 5401 Valve jet Fitment / change note → 1
26 4226 121 0700 Cup plug Fitment / change note → 1
27 4226 121 0800 End cover 1
28 4226 121 2700 Cap 1
29 4226 121 8600 Washer Fitment / change note → 1
30 4137 120 8700 Control valve Fitment / change note → 1
31 1123 122 6200 Idle speed adjustment screw Fitment / change note → 1
32 1125 122 4200 Clamp Fitment / change note → 1
33 4137 121 8600 Washer 1
Not numbered on the diagram — assemblies, kits and options
— 4137 120 0600 Carburetor C1Q-S28E Fitment / change note → 1
— 4137 120 0602 Carburetor C1Q-S41C Fitment / change note → 1
— 4227 007 1060 Set of carburetor parts Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 75 / FS 80 / FS 80 R / FS 85 / FS 85 R

FS 75 / 80 / 85: C1Q-S28A fixed-jet specification

Zama C1Q-S28A has no H screw; L standard setting is one turn and idle is 2,800 rpm. These settings do not identify later S28E/S41C carburetors.

  • All-position diaphragm carburetor with integral fuel pump. Original figure 366TI004 labels B = idle fixed jet, diameter 0.32 mm; C = valve jet with integral fixed jet, diameter 0.41 mm. These lettered drillings are not part numbers or adjustable screw settings; no reaming/modification instruction is supplied.
  • Table 2.1.2 names Zama C1Q-S28A: low-speed screw L standard setting OPEN ONE TURN; idle speed 2,800 rpm; high-speed adjusting screw H NONE. Do not invent an H setting from the fixed high-speed jet described on page 2.
  • Cut-off speed is 9,500–11,500 rpm WITHOUT CUTTING TOOL; this is a printed test condition, not authorization to run a machine. Do not confuse it with the separate rated output-shaft speeds or use it as a universal loaded maximum. Section 6.1 adjustment setup and symptom-specific corrections on pages 9–10 are retained in the separately reviewed C1Q-S28A notes; the applicable owner’s manual is a documented source gap; service-literature review remains pending.
  • Fuel capacity 0.44 l (0.9 US pt). No mixture ratio or fuel grade is given in this opening section.
  • Later linked IPL sheet L names C1Q-S28E and C1Q-S41C and a 1999 serial event. It is a historical discovery destination only: S28A is NOT established as S28E/S41C, and no later assembly order number, jet calibration or serial is imported into the 1996 specification.
  • Scope is the 1996 series 4137 introduction, including depicted R and RB handle arrangements. No scope is inherited by FS 85 T/RX, FC/FR/HL/HT/KM/KW/SP models or later same-named machines from a shared IPL sheet. Historical source guidance, not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 36/1996, p. 2 · TI 36/1996, p. 4 — FS 75 / 80 / 85: C1Q-S28A fixed-jet specification.

No additional parts-table entry added.

Service note · FS 75 / FS 80 / FS 80 R / FS 85 / FS 85 R

FS 75 / 80 / 85: C1Q-S28A carburetor parts kit

4227 007 1060 is listed for S28A; no kit contents or later-carburetor equivalence are established.

  • Section 5.2 assigns carburetor parts kit 4227 007 1060 to Zama C1Q-S28A. No list of included parts, seal materials, jet sizes or supersession is supplied on this page. Do not equate a parts kit with a complete carburetor.
  • The linked later IPL sheet names C1Q-S28E / C1Q-S41C and lists 4227 007 1060 among its repair parts. Shared kit listing does NOT establish identical complete carburetors, calibration, all included components at every date, or unrestricted model interchange.
  • Section 6 requires compliance with all local regulations and the safety precautions in the OWNER’S MANUAL if the unit is started during repair or maintenance. This note is not a complete operating/safety procedure. SOURCE GAP: the applicable owner’s manual was not identified in the bounded local search. Later workshop manuals are not a substitute; page 8 closes with this named gap, not a complete safety procedure. No machine was started.
  • Historical 1996 FS 75/80/85 guidance only; no applicability inherited by FS 85 T/RX or FC/FR/HL/HT/KM/KW/SP machines from shared IPL sheets. No hardware operation was performed.

Source: TI 36/1996, p. 8 — FS 75 / 80 / 85: C1Q-S28A carburetor parts kit.

Part numbers (1)
  • 4227 007 1060 — Carburetor parts kitListed servicing aid · Zama C1Q-S28A as specified by TI36/1996

Service note · FS 75 / FS 80 / FS 80 R / FS 85 / FS 85 R

FS 75 / 80 / 85: C1Q-S28A adjustment setup

L opens one turn from its gently seated position; the mounted cutting tool and warm-engine conditions matter.

  • Section 6.1 explicitly names Zama C1Q-S28A, has NO high-speed adjusting screw H, and attributes reduced idle/part-load emissions to a lean idle mixture. The standard setting is L = OPEN ONE TURN: carefully screw the low-speed screw clockwise against its seat, then one turn counterclockwise. Do not substitute the idle-speed screw LA.
  • The source requires the CUTTING TOOL MOUNTED. If a nylon-line head is fitted, EACH line extends as far as the limiting blade on the deflector. Check the air filter and clean if necessary; start and warm the engine; use LA to set idle to 2,800 rpm. This mounted-tool adjustment condition is distinct from the WITHOUT-CUTTING-TOOL cut-off-speed specification on page 4.
  • Figure 392TI009 identifies upper L and lower LA; neither is an H screw. This historical setup is not a complete operating/safety procedure. Section 6 owner-manual and local-regulation requirements remain applicable, with the applicable owner’s manual now a documented source gap after bounded local search, not a waived prerequisite. No machine was started.
  • Historical 1996 FS 75/80/85 guidance only; no applicability inherited by FS 85 T/RX or FC/FR/HL/HT/KM/KW/SP machines from shared IPL sheets. No hardware operation was performed.
  • The linked later IPL names C1Q-S28E / C1Q-S41C. It is a discovery destination, not proof those carburetors share the C1Q-S28A settings or procedures; no later calibration or assembly number is imported.

Source: TI 36/1996, p. 9 — FS 75 / 80 / 85: C1Q-S28A adjustment setup.

No additional parts-table entry added.

Service note · FS 75 / FS 80 / FS 80 R / FS 85 / FS 85 R

FS 75 / 80 / 85: C1Q-S28A symptom-specific idle corrections

Poor acceleration uses counterclockwise L correction; full-load-to-idle stalling uses clockwise L correction. A rotating tool instead uses LA.

  • For POOR ACCELERATION OR ENGINE STALLS, page 9 first checks standard L = 1. It then prints one "eight" turn COUNTERCLOCKWISE on L, resets idle to 2,800 rpm with LA, and repeats those two adjustments if necessary. The paired following paragraph prints "one eighth". The first paragraph spelling is retained as a source typo; this is an eighth-turn increment, not eight turns.
  • For STALLING DURING TRANSITION FROM FULL LOAD TO IDLE or ERRATIC IDLING, check standard L = 1, turn L ONE EIGHTH TURN CLOCKWISE, then reset idle to 2,800 rpm with LA. Repeat the L correction and idle reset if necessary. The opposite directions belong to different printed symptom groups; do not merge them into a universal adjustment.
  • For a CUTTING TOOL ROTATING AT IDLE, page 10 first sets idle to 2,800 rpm with LA; then turns LA COUNTERCLOCKWISE until the tool stops and another ONE HALF TURN in the SAME direction. This final half turn is on LA, not L. The source does not command resetting 2,800 rpm again after this final step.
  • These corrections follow the section 6.1 standard setup, mounted-tool/line-length, filter and warm-engine conditions. The source gives no maximum repeat count or resulting final L setting. It does not establish a repair for a mechanically faulty clutch or authorize unattended operation; the applicable owner’s manual is a documented source gap after bounded local search, not a waived safety prerequisite.
  • Historical 1996 FS 75/80/85 guidance only; no applicability inherited by FS 85 T/RX or FC/FR/HL/HT/KM/KW/SP machines from shared IPL sheets. No hardware operation was performed.
  • The linked later IPL names C1Q-S28E / C1Q-S41C. It is a discovery destination, not proof those carburetors share the C1Q-S28A settings or procedures; no later calibration or assembly number is imported.

Source: TI 36/1996, p. 9 · TI 36/1996, p. 10 — FS 75 / 80 / 85: C1Q-S28A symptom-specific idle corrections.

No additional parts-table entry added.

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85

FH/HL/HT/FC/FS: C1Q-S28, S41 and BIS S45 are distinct

0600 retains its control valve, 0602 does not; the new 0603 uses integral LD adjustment and a separately removable fixed jet.

1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.

  • The C1Q-S41 with external idle-speed screw LA is replaced in the new configuration by C1Q-S45 with integral idle-speed screw LD and balanced idle system (BIS). Its venturi is about 1 mm larger; no absolute carburetor bore dimension is printed. The detailed benefits, construction and function are delegated to the Carburetors handbook, not established by the acronym alone. The separate handbook was not identified in the retained reference index, PDF inventory and manual headers; model-manual citations do not supply its missing balanced-idle explanation.
  • The page-2 left drawing labels L and LA on S41; the right labels LD on S45. Old valve jet A has an inseparable fixed jet. On the new carburetor, fixed jet C screws into outlet valve B. The removable fixed jet does not make the precision-installed outlet valve a permitted workshop replacement.
  • The earlier-machine prose allows 0602 (LA screw, no control valve), previously production-only, in place of 0600 (printed as H and LA screws, with control valve). The literal H wording is retained as a source discrepancy alongside the page-2 L marking and summary low-speed-screw row; it is not silently corrected or used to prescribe an H adjustment.
  • The stated future factory supply of 0602 includes full instructions, which determine whether an electronic-cut-off ignition module is necessary. TI41/1997 section 1.3 must additionally be observed; its linked original summary and service context are now reviewed below. The supplied 0602 instruction sheet itself was not identified in the bounded retained corpus and cannot be reconstructed from that citation. This conditional 0602-for-0600 option is not permission to replace either with 0603 as an isolated part. Earlier-machine gaskets 4114 149 1205 go on both sides of the heat shield.
  • Summary remarks retain the original 0600 with control valve and 0602 without control valve for earlier machines. Dashes in the New column are not discontinuation notices. The later catalog calls these C1Q-S28E and C1Q-S41C; suffix equivalence is not assumed. The HT70/75 S41C row has a blank number, not proof that its missing catalog cell contains 0602. The TI supplies the historical number independently.
  • The cited TI41/1997 section 1.3 is the page-4 Summary, not a complete standalone installation procedure. Its surrounding section 1.2 and 1.2.2 supply the speed-limiting service rules. The original prints 1.3.1 above the introduction table on page 2 but points to 1.2.1 on page 4; that numbering discrepancy is retained, not silently repaired.
  • For FC 75, FS 75/80/85, HL 75 and HT 75 explicitly shared by both bulletins, TI41/1997 requires ESL ignition module 4137 400 1307 when the carburetor has no speed-control valve. Do not operate without maximum-speed limitation: engine damage may result. A valve-equipped service carburetor plus an already-fitted ESL module is explicitly allowed and is said not to affect performance or operation; neither limiter is to be disabled. TI41 also covers HS and BG machines, but those are not added to this TI21 note. Its BG75 fan-load exception does not apply to these shared models.
  • TI41/1997 identifies ESL by disassembled-module marking 1306 or 1307. Version 1307 adds the ignition-cable insulating hose and is the general replacement; identification is not proof of a working limiter. No full order number is inferred from marking 1306. FH 75, HL 75 K and HT 70 are not explicitly named in TI41; their TI21 electronic-cut-off requirement remains, but a model-specific 1307 prescription is not inferred from a shared catalog sheet.
  • The availability statements are dated: TI41/1997 summary remark 5 says C1Q-S41 is not supplied as a single part (the printed -*- is not an order number); TI21/1999 subsequently announces 4137 120 0602 as a future factory replacement with instructions. Both statements remain visible. This later announcement changes the stated supply policy, not the requirement to retain maximum-speed limitation, and is not evidence of current stock or of having recovered the supplied sheet.
  • TI41/1997 section 4 confirms gasket 4114 149 1205 on both sides of the heat shield, quantity 2, and requires missing gaskets to be fitted on original versions. TI21 independently repeats both-side placement for its earlier machines. This corroboration does not extend the older bulletin to unlisted model variants or provide the missing installation instructions.
  • The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
  • The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
  • For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
  • Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
  • TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.

Source: TI 21/1999, p. 1 · TI 21/1999, p. 2 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — 1.2 complete construction comparison; 1.5.1–1.5.3; summary items 3–5 and remarks 1–3.

Referenced bulletin evidence: TI 41/1997, p. 2 · TI 41/1997, p. 3 · TI 41/1997, p. 4 · TI 41/1997, p. 6 — Referenced section 1.3 summary with necessary 1.2/1.2.2 context; section 4 confirms both heat-shield gaskets.

Part numbers (4)
  • 4137 120 0600 — Carburetor C1Q-S28Original, with control valve · Summary item 3 includes items 6, 7 and 13–20; remains for earlier machines
  • 4137 120 0602 — Carburetor C1Q-S41Original, without control valve · Summary item 4 includes items 6, 7 and 13–18; remains for earlier machines
  • 4137 120 0603 — Carburetor C1Q-S45New BIS carburetor · Summary item 5 includes items 6–12; matched new engine configuration
  • 4114 149 1205 — GasketEarlier-machine heat-shield gasket · Install on both sides of heat shield; not one gasket total

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85

FH/HL/HT/FC/FS: retained C1Q-S28 and S41 internal parts

The original parts remain spares; control valve 8700 and washer 8600 belong to the S28 inclusion list, not the S41 list.

1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.

  • C1Q-S28 includes original items 6, 7 and 13 through 20; C1Q-S41 includes original items 6, 7 and 13 through 18. The explicit lists do not transfer the S28 control valve or washer to S41. TI item numbers are not later catalog positions or quantities.
  • Every listed original component has remark 1: the original version remains available as a spare. Rows 13–20 have dashes in the New column, not new part numbers or proof of unavailable original stock. All other parts are stated to be as carburetor C1Q-S28; this is not blanket interchange of the separately changed components.
  • The original calls 1125 122 4200 a Ball; the later exact-model catalog calls that same number Clamp. Both descriptions are retained without deciding its physical form from text. The original Sealing plate 4226 121 0700 is called Cup plug in the later catalog. Catalog wording is not substituted into the original table.
  • The later catalog contains each listed original internal-part number on the exact-model S28E/S41C sheets. Its shared sheet does not override the TI inclusion exclusions, establish suffix equivalence or extend applicability to extra models on that sheet.
  • The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
  • The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
  • For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
  • Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
  • TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.

Source: TI 21/1999, p. 1 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — Summary rows 3–4, 6–7 and 13–20, inclusion lists and remarks 1–3.

Part numbers (10)
  • 4227 121 3300 — Throttle shutterOriginal summary item 6; remains a spare · C1Q-S28 and C1Q-S41
  • 1123 121 0800 — End coverOriginal summary item 7; remains a spare · C1Q-S28 and C1Q-S41
  • 4226 121 0700 — Sealing plateOriginal summary item 13; remains a spare · C1Q-S28 and C1Q-S41
  • 4137 122 6800 — Low speed screwOriginal summary item 14; remains a spare · C1Q-S28 and C1Q-S41
  • 1123 122 6200 — Idle speed screwOriginal summary item 15; remains a spare · C1Q-S28 and C1Q-S41
  • 4137 121 5401 — Valve jetOriginal summary item 16; remains a spare · C1Q-S28 and C1Q-S41
  • 1120 122 3005 — SpringOriginal summary item 17; remains a spare · C1Q-S28 and C1Q-S41
  • 1125 122 4200 — BallOriginal summary item 18; remains a spare · C1Q-S28 and C1Q-S41
  • 4137 120 8700 — Control valveOriginal summary item 19; remains a spare · C1Q-S28 inclusion only; not included in S41
  • 4226 121 8600 — WasherOriginal summary item 20; remains a spare · C1Q-S28 inclusion only; not included in S41

Wrong number or missing part for the FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX? Report a correction →