Stihl 4137 · Section K · 10 of 25 · 32 parts
Carburetor C1Q-S45 (16.2001)
Fits FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (32)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4226 120 7100 | Throttle shaft with lever | 1 |
| 2 | 1123 122 3000 | Spring | 1 |
| 3 | 4137 121 3300 | Throttle shutter Fitment / change note → | 1 |
| 4 | 1125 122 7403 | Round head screw | 1 |
| 5 | 1125 122 9001 | E-clip | 1 |
| 6 | 4137 121 8900 | Pin → replaced by 4128 121 8900 TI 41/1997 | 1 |
| 7 | 1120 122 9000 | E-clip | 1 |
| 8 | 1129 121 4800 | Pump diaphragm | 1 |
| 9 | 1123 129 0905 | Gasket | 1 |
| 10 | 4128 121 0800 | End cover Fitment / change note → → replaced by 1130 121 0801 TI 31/2009 | 1 |
| 11 | 1120 122 7800 | Oval head screw | 1 |
| 12 | 4116 121 5100 | Inlet needle | 1 |
| 13 | 1123 122 3001 | Spring | 1 |
| 14 | 1125 121 5000 | Inlet control lever | 1 |
| 15 | 1120 121 9200 | Spindle | 1 |
| 16 | 1120 122 6600 | Collar screw | 1 |
| 17 | 4129 129 0902 | Gasket Fitment / change note → | 1 |
| 18 | 4129 121 4700 | Metering diaphragm Fitment / change note → | 1 |
| 19 | 4226 120 2200 | Flange Fitment / change note → | 1 |
| 20 | 4226 122 7100 | Screw Fitment / change note → | 2 |
| 21 | 4137 122 6300 | Idle speed adjustment screw Fitment / change note → | 1 |
| 22 | 1128 122 7100 | Screw Fitment / change note → | 2 |
| 23 | 1123 121 7800 | Strainer | 1 |
| 24 | 4137 122 5100 | Outlet valve Fitment / change note → | 1 |
| 25 | 4137 121 5601 | Fixed jet 0.42 Fitment / change note → | 1 |
| 26 | 4119 121 0700 | Cup plug Fitment / change note → | 1 |
| 27 | 4129 121 0700 | Cup plug Fitment / change note → | 1 |
| 28 | 4226 121 0800 | End cover Fitment / change note → | 1 |
| 29 | 4226 121 2700 | Cap | 1 |
| 30 | 4137 121 8600 | Washer | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4137 120 0603 | Carburetor C1Q-S45 Fitment / change note → | 1 |
| — | 4227 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
4137 LD carburetors: four-screw primer flange kit
C1Q-S56 replaces C1Q-S45 for previous machines; the flange kit is not the new-cylinder carburetor.
- The two-screw end cover can distort the primer flange and metering diaphragm. The revised end cover and flange use four screws. On previous carburetors, exchange flange and cover together with the two additional longer screws; do not change only one component.
- Unresolved screw-number conflict: page 3 prose specifies 4226 121 7100; page 4 summary item 9 specifies 4226 122 7100, quantity increased from two to four. Both original scans agree with their respective text. Neither number is silently corrected or certified as the right screw.
- Page 3 drawing identifies A screws, B/B1 old/new end cover, C/C1 old/new flange, D metering diaphragm and E gasket. Kit comprises A, B1, C1, D, E. Page 4 instructs finger-tight insertion, then alternate diagonal tightening. No torque is stated; separately supplied kit installation instructions are referenced but were not located in the retained STIHL service documentation document index/resources or supplemental manual PDFs. Later workshop flange sections are not the exact kit instructions; this remains a documented source gap.
- Common unchanged diaphragm 4129 121 4700 and gasket 4129 129 0902 remain listed. Previous two-screw item 8 is 1128 122 7100; item 9 is 4226 122 7100. Old end cover 4226 121 0800 remains a spare for other models; the new end cover and flange are not separate supply items. Summary asterisks/dashes are not new order numbers.
- For the twelve cover models, two-screw C1Q-S45, 4137 120 0603 (includes items 4–9), is replaced by four-screw C1Q-S56, 4137 120 0604 (includes kit item 3). The former is supplied only while stocks last. Both are old-generation BIS/LD carburetors, not replacements for the new-cylinder C1Q-S63.
- Flange kit 4140 120 2250 contains summary items 4–7 and 9; previous flange 4226 120 2200 is replaced by this kit. The new flange applies as spare to Zama C1Q carburetors with LD screw, within each model-specific kit assignment, not every C1Q regardless of version.
- Page 7 older-machine serial 2 49 848 196 conflicts with page 2 FS 85 introduction 2 49 849 196; this record does not manufacture a clean serial boundary.
- Only explicitly named models and configurations are covered. Shared IPL pages do not extend these assertions to unnamed R/RX or other variants. Availability statements describe 2001 factory support, not present stock. The printed cover places FH/HL under 4230, HT under 4138 and KW under 4602; retained exact-model engine sheets use 4137 as navigation, not proof of series equivalence.
Source: TI 16/2001, p. 1 · TI 16/2001, p. 3 · TI 16/2001, p. 4 · TI 16/2001, p. 5 · TI 16/2001, p. 7 — Sections 3.1–3.1.5 and 3.2.5: primary-model flange replacement, drawing, every common row and remarks.
Part numbers (10)
- 4137 120 0603 — Carburetor C1Q-S45, two screwsPrevious BIS/LD · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 120 0604 — Carburetor C1Q-S56, four screwsReplacement BIS/LD · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4140 120 2250 — Flange kitItems 4–7 and 9 · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4226 120 2200 — Previous primer flangeUse flange kit · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4226 121 0800 — Previous end coverRemains for other models; new cover not separate · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4129 121 4700 — Metering diaphragmUnchanged · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4129 129 0902 — GasketUnchanged · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 1128 122 7100 — Previous screw, item 8Two in old arrangement · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4226 122 7100 — Screw, summary item 9Four in new arrangement; conflicts with prose · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4226 121 7100 — Longer screw as printed in proseUnresolved conflict with summary · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85
FH/HL/HT/FC/FS: C1Q-S28, S41 and BIS S45 are distinct
0600 retains its control valve, 0602 does not; the new 0603 uses integral LD adjustment and a separately removable fixed jet.
1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.
- The C1Q-S41 with external idle-speed screw LA is replaced in the new configuration by C1Q-S45 with integral idle-speed screw LD and balanced idle system (BIS). Its venturi is about 1 mm larger; no absolute carburetor bore dimension is printed. The detailed benefits, construction and function are delegated to the Carburetors handbook, not established by the acronym alone. The separate handbook was not identified in the retained reference index, PDF inventory and manual headers; model-manual citations do not supply its missing balanced-idle explanation.
- The page-2 left drawing labels L and LA on S41; the right labels LD on S45. Old valve jet A has an inseparable fixed jet. On the new carburetor, fixed jet C screws into outlet valve B. The removable fixed jet does not make the precision-installed outlet valve a permitted workshop replacement.
- The earlier-machine prose allows 0602 (LA screw, no control valve), previously production-only, in place of 0600 (printed as H and LA screws, with control valve). The literal H wording is retained as a source discrepancy alongside the page-2 L marking and summary low-speed-screw row; it is not silently corrected or used to prescribe an H adjustment.
- The stated future factory supply of 0602 includes full instructions, which determine whether an electronic-cut-off ignition module is necessary. TI41/1997 section 1.3 must additionally be observed; its linked original summary and service context are now reviewed below. The supplied 0602 instruction sheet itself was not identified in the bounded retained corpus and cannot be reconstructed from that citation. This conditional 0602-for-0600 option is not permission to replace either with 0603 as an isolated part. Earlier-machine gaskets 4114 149 1205 go on both sides of the heat shield.
- Summary remarks retain the original 0600 with control valve and 0602 without control valve for earlier machines. Dashes in the New column are not discontinuation notices. The later catalog calls these C1Q-S28E and C1Q-S41C; suffix equivalence is not assumed. The HT70/75 S41C row has a blank number, not proof that its missing catalog cell contains 0602. The TI supplies the historical number independently.
- The cited TI41/1997 section 1.3 is the page-4 Summary, not a complete standalone installation procedure. Its surrounding section 1.2 and 1.2.2 supply the speed-limiting service rules. The original prints 1.3.1 above the introduction table on page 2 but points to 1.2.1 on page 4; that numbering discrepancy is retained, not silently repaired.
- For FC 75, FS 75/80/85, HL 75 and HT 75 explicitly shared by both bulletins, TI41/1997 requires ESL ignition module 4137 400 1307 when the carburetor has no speed-control valve. Do not operate without maximum-speed limitation: engine damage may result. A valve-equipped service carburetor plus an already-fitted ESL module is explicitly allowed and is said not to affect performance or operation; neither limiter is to be disabled. TI41 also covers HS and BG machines, but those are not added to this TI21 note. Its BG75 fan-load exception does not apply to these shared models.
- TI41/1997 identifies ESL by disassembled-module marking 1306 or 1307. Version 1307 adds the ignition-cable insulating hose and is the general replacement; identification is not proof of a working limiter. No full order number is inferred from marking 1306. FH 75, HL 75 K and HT 70 are not explicitly named in TI41; their TI21 electronic-cut-off requirement remains, but a model-specific 1307 prescription is not inferred from a shared catalog sheet.
- The availability statements are dated: TI41/1997 summary remark 5 says C1Q-S41 is not supplied as a single part (the printed -*- is not an order number); TI21/1999 subsequently announces 4137 120 0602 as a future factory replacement with instructions. Both statements remain visible. This later announcement changes the stated supply policy, not the requirement to retain maximum-speed limitation, and is not evidence of current stock or of having recovered the supplied sheet.
- TI41/1997 section 4 confirms gasket 4114 149 1205 on both sides of the heat shield, quantity 2, and requires missing gaskets to be fitted on original versions. TI21 independently repeats both-side placement for its earlier machines. This corroboration does not extend the older bulletin to unlisted model variants or provide the missing installation instructions.
- The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
- The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
- For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
- Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
- TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.
Source: TI 21/1999, p. 1 · TI 21/1999, p. 2 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — 1.2 complete construction comparison; 1.5.1–1.5.3; summary items 3–5 and remarks 1–3.
Referenced bulletin evidence: TI 41/1997, p. 2 · TI 41/1997, p. 3 · TI 41/1997, p. 4 · TI 41/1997, p. 6 — Referenced section 1.3 summary with necessary 1.2/1.2.2 context; section 4 confirms both heat-shield gaskets.
Part numbers (4)
- 4137 120 0600 — Carburetor C1Q-S28Original, with control valve · Summary item 3 includes items 6, 7 and 13–20; remains for earlier machines
- 4137 120 0602 — Carburetor C1Q-S41Original, without control valve · Summary item 4 includes items 6, 7 and 13–18; remains for earlier machines
- 4137 120 0603 — Carburetor C1Q-S45New BIS carburetor · Summary item 5 includes items 6–12; matched new engine configuration
- 4114 149 1205 — GasketEarlier-machine heat-shield gasket · Install on both sides of heat shield; not one gasket total
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85
FH/HL/HT/FC/FS: C1Q-S45 includes summary items 6–12
The BIS carburetor has new shutter, cover, LD screw, outlet valve, fixed jet and two separately numbered sealing plates.
1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.
- New carburetor 4137 120 0603 includes new items 6–12. The exploded drawing labels 6, 7, 8, 9, 10, 11 and 12; two sealing plates have different order numbers. Items 8–12 have no previous number. The unchanged-parts statement refers to C1Q-S28 and does not turn the new roster into an unrestricted retrofit kit.
- The original table lists outlet valve 4137 122 5100, but section 1.5.6 explicitly says not to replace outlet valves: the required factory installation precision cannot be achieved with normal service-shop equipment. Parts availability does not override that prohibition.
- The later exact-model S45 sheets retain all seven numbers, label 4137 121 5601 Fixed jet 0.42 and label both sealing plates Cup plug. The original TI does not print a jet size or unit, so the later 0.42 label is not converted to a measured dimension, tolerance or revised TI setting. No supplied tool, jet torque or individual-part quantity is inferred.
- The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
- The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
- For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
- Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
- TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.
Source: TI 21/1999, p. 1 · TI 21/1999, p. 2 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 5 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — 1.2 outlet-valve construction; 1.5.6 service restriction; full exploded drawing and summary rows 5–12.
Part numbers (7)
- 4137 121 3300 — Throttle shutterNew summary item 6 · C1Q-S45 new configuration
- 4128 121 0800 — End coverNew summary item 7 · C1Q-S45 new configuration
- 4137 122 6300 — Idle speed screwNew summary item 8 · C1Q-S45 new configuration
- 4137 122 5100 — Outlet valveNew summary item 9 · C1Q-S45 only; outlet valve is factory-installed, not a workshop replacement
- 4137 121 5601 — Fixed jetNew summary item 10 · C1Q-S45 new configuration
- 4119 121 0700 — Sealing plateNew summary item 11 · C1Q-S45 new configuration
- 4129 121 0700 — Sealing plateNew summary item 12 · C1Q-S45 new configuration
Service note · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85
FH/HL/HT/FC/FS: set the C1Q-S45 throttle cable at its stop
Back off the tensioner first, hold full throttle, then adjust until the carburetor lever touches its stop and recheck.
1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.
- After installing C1Q-S45, back off adjusting screw 1 on tensioner 2 counterclockwise until the tensioner butts against the spacer flange. Pull the throttle trigger fully to its stop and hold it there in the full-throttle position.
- Check that throttle lever 3 butts against the carburetor stop indicated by the drawing arrow. If necessary, turn adjusting screw 1 clockwise until the throttle lever touches the stop. Release the throttle trigger, check the setting and readjust if necessary.
- On FS units with a bike handle, the control handle must be mounted on the handlebar before making adjustments. Drawing labels 1–3 identify the screw, tensioner and throttle lever only; they are not parts-order numbers. This cable operation does not instruct starting the engine, bending a lever or adding unspecified cable free play.
- The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
- The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
- For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
- Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
- TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.
Source: TI 21/1999, p. 1 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — 1.5.4 complete ordered throttle-cable adjustment and bike-handle warning.
No additional parts-table entry added.
Service note · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85
FH/HL/HT/FC/FS: C1Q-S45 LD is a left-hand-thread adjustment
Seat LD counterclockwise, then open two full turns clockwise; retain the separate stalling, rotating-tool and erratic-idle corrections.
1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.
- Preparations are model-specific: mount the cutting tool on FC and FS; on FH and HL check and, if necessary, clean the cutting blades, which must be clean, lubricated, freely moving and not warped; on HT check chain tension. Check the air filter and replace if necessary. Inspect the spark-arresting screen if fitted and clean or replace as needed.
- For the standard setting, carefully screw LD counterclockwise down onto its seat: it has a left-hand thread. From that seated position, open it 2 full turns clockwise. Do not transfer the direction or setting to an LA or L screw on the earlier carburetors.
- Before idle-speed adjustment, carry out the standard setting, then start and warm the engine as the historical procedure specifies. If the engine stops while idling, turn LD slowly clockwise until the engine runs smoothly; the cutting tool must not rotate.
- If the cutting tool rotates at idle, turn LD counterclockwise until it stops rotating, then turn the screw about 1 full turn further in the same direction. This additional turn belongs to that branch, not to the initial two-turn standard setting.
- For erratic idling or poor acceleration, turn LD slowly counterclockwise, but not more than half a turn. This cap belongs to that correction branch. No numerical idle rpm, high-speed setting, seat torque or permission to tolerate a moving cutting tool is supplied. Running instructions are documented source evidence only; no hardware was energized or adjusted.
- The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
- The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
- For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
- Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
- TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.
Source: TI 21/1999, p. 1 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 5 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — 1.5.5 all model-specific preparations, standard setting and three idle-correction branches.
No additional parts-table entry added.
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85
FH/HL/HT/FC/FS: clean the S45 fixed jet, not its outlet valve
Use a standard screwdriver and fresh fuel or compressed air; never needles, wire or fibrous cloth, and tighten by hand.
1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.
- The outlet valve is installed in a precision factory process that normal service-shop equipment cannot reproduce. The source recommendation is explicit: Do not replace outlet valves. Its appearance in the parts table is not workshop replacement authorization.
- To support proper fuel delivery, periodically replace the pickup body, clean the fuel tank and storage can at regular intervals, and use the gasoline and two-stroke engine oil specified in the owner's manual and shop manual. No numerical maintenance interval, fuel ratio or lubricant grade is given here; later manual evidence is bounded below, with the original-edition gap retained.
- Later fuel evidence, not a 1999 specification: RA_394_00_01_02 (2004-06), section 3.1, printed page 4 / PDF page 5, specifies regular brand-name gasoline with minimum 90 RON and STIHL 50:1 two-stroke engine oil, referring to the instruction manual for further details. Its cover and introduction explicitly overlap TI21 only for FC 75, FH 75, FS 75, FS 80, FS 85 and HL 75. HL 75 K is not explicitly named; the shared HL catalog sheet is not proof of that variant's manual coverage. The cover also lists SP 81 although the introduction roster and page footers omit it; no applicability is inferred from that discrepancy.
- Later HT fuel evidence: RA_386_00_01_02 (2005-04) expressly names HT 70 and HT 75 in its introduction. Section 3.1, printed page 4 / PDF page 5, likewise specifies regular brand-name gasoline (minimum 90 RON) with STIHL 50:1 two-stroke engine oil and refers to the instruction manual for further details. The retained unmatched HT75 PDF is byte-identical to this later edition, not an independent 1999 source.
- RON is the printed octane scale, not a 90 AKI pump rating. The STIHL 50:1 oil wording does not establish approval of every other two-stroke oil, an alternative mixing ratio, ethanol limits, a storage interval or a separate bar/gear lubricant. Neither later manual establishes the exact owner/shop-manual editions referenced in 1999. The Series 4137 Powerhead manual (2004-03) delegates component service back to the component manuals and supplies no missing exact owner-manual identity.
- Both later manuals' section 2 warns that gasoline is extremely flammable and can be explosive: keep fire, flame, sparks and other heat sources away, perform fuel work outdoors only and wipe spills immediately. They also require local safety rules and the instruction manual's precautions if an engine is started during service. No fuel was handled and no engine was run; the later fuel-mixture row is not a complete operating procedure.
- Use a standard screwdriver to unscrew the fixed jet for cleaning or replacement. Clean it in fresh fuel and/or blow it clear with compressed air. Never clean the jet with needles, wires or fibrous cloths. No drill, reaming, ultrasonic process or air-pressure value is specified.
- Reinstall the fixed jet by screwing it down carefully and tightening by hand. No torque value is supplied. Section 1.5.6 drawing 1/2 means outlet valve/fixed jet; section 1.2 uses B/C and summary 9/10 for the same distinction. The old S41 valve jet has an inseparable fixed jet and is not assigned this removable-jet procedure.
- The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
- The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
- For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
- Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
- TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.
TI dependency: TI 21/1999, p. 1 · TI 21/1999, p. 2 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 5 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — 1.5.6 complete outlet-valve restriction, maintenance prerequisites, fixed-jet removal/cleaning/installation; 1.2 and summary items 9–10.
Later manual evidence: Series 4137 Components FC, FH, FS, HL, KM, KW service manual (2004-06), section 1 exact-model applicability, 2 fuel-handling precautions, 3.1 fuel-mixture row only; later edition, not the unidentified 1999 edition, PDF pages 1, 3, 4, 5 · Series 4137 Components HT service manual (2005-04), section 1 exact-model applicability, 2 fuel-handling precautions, 3.1 fuel-mixture row only; later edition, not the unidentified 1999 edition, PDF pages 1, 3, 4, 5
Part numbers (2)
- 4137 122 5100 — Outlet valvePrecision factory installation; do not replace · C1Q-S45; drawing item 1, summary item 9
- 4137 121 5601 — Fixed jetRemovable for cleaning or replacement · C1Q-S45; drawing item 2, summary item 10
Wrong number or missing part for the FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX? Report a correction →