← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section P · 15 of 25 · 19 parts

Handle (24.2002)

Fits FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX.

Parts diagrams →

Historical fitment & changes (11) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415223330456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (19)

PosPart numberDescriptionQty
1 4137 790 1101 Handle molding, inner Fitment / change note → 1
2 4137 791 9400 Hose clamp Fitment / change note → 2
3 9022 341 0960 Spline screw IS-M5x12 Fitment / change note → → replaced by 9022 341 0980 TI 3/2006 2
4 4137 442 1600 Contact spring Fitment / change note → 1
5 4137 182 1700 Slide control Fitment / change note → 1
6 4137 182 1000 Throttle trigger Fitment / change note → 1
7 4137 182 4500 Torsion spring Fitment / change note → 1
8 4137 182 0801 Lockout lever Fitment / change note → 1
9 4137 791 0800 Handle molding, outer Fitment / change note → 1
10 9074 478 3025 Pan head self-tapping screw IS-P4x16 Fitment / change note → 4
11 4137 180 1103 Throttle cable Fitment / change note → 1
11 4137 180 1150 Throttle cable Fitment / change note → 1
12 4137 440 1101 Short circuit wire 1
13 0000 442 2100 Shrink-on tube 1
14 4137 182 4503 Torsion spring 1
15 not sold separately Hose 185 mm / 7 5/16'' not available as a separate item 1
30 4137 182 4502 Torsion spring 1
Not numbered on the diagram — assemblies, kits and options
— 4137 790 1350 Control handle Fitment / change note → 1
— 4203 711 7201 Hose 960 mm / 37 13/16'' Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 controls: coordinated retrofit and ground connector

The new control handle needs the new cable and, on earlier machines, an added ignition-module ground connector.

  • The new control handle may be installed on previous machine versions only with the new throttle cable and a retrofitted ignition-module connector 4137 405 1600. The control handle and throttle cable remain separate replacement assemblies; buying a handle does not include the cable.
  • The new cable assembly comprises corrugated tube, cable and sealed microswitch with permanently connected water-tight short-circuit wires. Its individual parts, including the microswitch, are not separately supplied. Two fully insulated wires run directly to the ignition module; black connects to the primary-circuit connector, blue to the ground connector. Earlier machines require that ground connector to be mounted as well.
  • The handle is identified by its slide slot and gray-shaded non-slip surfaces in the diagram. The slide control operates the sealed ignition microswitch. Squeezing the trigger to its stop takes up cable slack: the sheath is attached to the slide, whose spring-loaded detent arm travels along the notched track. Initial installation requires adjustment; the instruction-manual chapter is referenced, and section 1.4.4 supplies the adjustment procedure within this TI. No missing manual is needed to establish this stated procedure.
  • The unrestricted interchangeability statement in section 2 concerns rewind-starter parts, not these coordinated control-handle changes.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 2 · TI 24/2002, p. 3 · TI 24/2002, p. 4 — Section1 introduction,1.1–1.2, summary item1 and1.4.1 wiring.

Part numbers (1)
  • 4137 405 1600 — Ignition-module ground connectorRequired retrofit on earlier machines · Named models and handle configuration only; coordinated retrofit conditions apply

Service note · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 controls: USA-production serial cutoffs

FS 80, FS 85 and HT 75 have separate USA cutoffs; KM 85 R is from production start.

  • USA production: FS 80 from serial 2 55 972 256; FS 85 from 2 55 809 184; HT 75 from 2 55 809 912. These are control-handle/throttle-cable changeovers, not whole-model production ranges, worldwide cutoffs or starter-rope changeovers.
  • KM 85 R: since start of production. Other models: introduction in progress. No numerical cutoff is supplied for those other models. Do not substitute one named model’s serial for another, or infer a separate serial for FS 85 RT/RX.
  • The printed USA production heading is preserved for this introduction table; the TI does not establish introduction timing for other production locations.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 3 · TI 24/2002, p. 4 — Section1.3 introduction table and model-specific scope.

No additional parts-table entry added.

Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 loop-handle control parts and old cable availability

Handle 4137 790 1307 and cable 4137 180 1107 have distinct contents; old cable 1150 had an approximate 2009 supply limit.

  • Loop-handled FH 75, HL 75, HT 70/75, FC 75/85, KM 85 R, KW 85 and FS 75/80/85/85 RT/85 RX only. Old control handle 4137 790 1350 includes summary items 16,17,19,20,22–24; new 4137 790 1307 includes 9,18,19,21–25. Item 9 is shared slide 4128 793 3000 from the bike-handle portion of the table, not a missing loop-handle part.
  • Old inner molding 4137 790 1101 and outer molding 4137 791 0800 give way to the new arrangement using handle 4137 790 0300. Slide control 4137 182 1700 becomes 4137 182 1701; old contact spring 4137 442 1600 has no new individual counterpart. New torsion spring 4137 182 4505 is added.
  • Throttle trigger 4137 182 1000 becomes 4137 182 1001; torsion spring 4137 182 4500 becomes 4137 182 4504; interlock lever 4137 182 0801 becomes 4137 182 0802; torsion spring 4128 182 4501 is added.
  • Previous cables 4137 180 1103 and 4137 180 1150 are listed. The latter explicitly includes summary items 16 and 24 (inner molding and interlock lever); that unusual source description is retained, not silently changed to microswitch contents. New cable 4137 180 1107 includes item 29, the microswitch with short-circuit wires, not separately available or assigned an order number.
  • Remark 1 keeps marked previous parts available as spares for older machines. Remark 3 instead states that old cable 4137 180 1150 remains available from the factory up to about 2009. This is an approximate historical supply statement, not a model end date, exact discontinuation date or present-stock claim. All other parts remain as before.
  • Retrofitting the new handle requires the new cable plus ignition-module connector 4137 405 1600. Neither the table nor shared catalog sheets grants interchange between bike and loop handles.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 2 · TI 24/2002, p. 3 · TI 24/2002, p. 4 — Section1.3 summary items14–29 plus shared slide item9, remarks1–3.

Part numbers (21)
  • 4137 790 1350 — Control handlePrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 790 1307 — Control handleNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 790 1101 — Inner handle moldingPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 791 0800 — Outer handle moldingPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 790 0300 — HandleNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 1700 — Slide controlPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 1701 — Slide controlNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 442 1600 — Contact springPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 4505 — Torsion springNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 1000 — Throttle triggerPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 1001 — Throttle triggerNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 4500 — Torsion springPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 4504 — Torsion springNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 0801 — Interlock leverPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 182 0802 — Interlock leverNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 182 4501 — Torsion springNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 793 3000 — SlideShared summary item9 · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 180 1103 — Throttle cablePrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 180 1150 — Throttle cable including items16/24Previous; factory supply up to about2009 · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 180 1107 — Throttle cable assemblyNew; includes non-separate microswitch/wires · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 405 1600 — Ignition-module connectorCoordinated retrofit · Named models and handle configuration only; coordinated retrofit conditions apply

Service note · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 loop handle: cable routing and trigger spring installation

Route blue then black; the spring’s straight end goes under the cable sleeve.

  • Seat the microswitch as illustrated. Push the blue ground wire into the channel first, then the black short-circuit wire, right to the end. Neither wire may project. Put both in recess 20 at corrugated-tube 19 attachment; the throttle cable is placed over the recess later, as shown in the drawing.
  • Press cable 11 into slide 12 until ferrule 13 snaps into place. Position the slide in the molding with the groove at the end of the slot: the basic adjustment position.
  • Attach cable end sleeve 14 to trigger 15. Push the straight end of spring 16 under the end sleeve, then put the ring-shaped part over pivot 17 on the trigger. Fit the trigger and put the spring loop around screw boss 18. Do not substitute the bike-handle instruction placing the spring in front of the sleeve.
  • Check corrugated tube and slide position. Do not squeeze the throttle trigger until section 1.4.4 adjustment. Screw the moldings together without pinching wires, attach cable to carburetor and reassemble powerhead. Slide the control handle onto the drive tube, secure the tube to the powerhead, then align and secure the control handle before adjusting.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 6 · TI 24/2002, p. 7 — Section1.4.3 all diagrams and installation steps.

No additional parts-table entry added.

Service note · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 controls: throttle adjustment, rechecks and travel limit

Adjust only fully assembled in the working position; unresolved travel-limit slack requires a new cable.

  • The cable is no longer routinely adjusted at the tensioner. For correct semi-automatic operation, set its screw so visible thread lengths above and below are equal. If this basic setting does not allow satisfactory operation, the source permits a slight screw correction; no numerical thread length or number of turns is given.
  • Adjust only when the machine is completely and securely assembled, with handlebar and control handle in the normal operating position. Use a screwdriver to press down the slide and push it to the end of its slot. Then press the trigger interlock and squeeze the trigger fully: the slide moves away from the end and takes up slack automatically. Carburetor adjustment may then be necessary; the TI supplies no carburetor screw setting.
  • Correct cable adjustment is required at full throttle, starting throttle and idle. Recheck if the trigger was squeezed too early during handling/mounting, after service or repair, before carburetor readjustment, after a large bike-handlebar position change, after cable stretch, or if snagging force changed the slide position.
  • The travel limit is reached when the slide touches the opposite end of the slot but free play remains. With interlock depressed and trigger fully squeezed, check that the throttle-shaft lever touches the carburetor body. If not, readjust the tensioner to take up slack. If that does not remedy it, install a new throttle cable. Simply reaching the slot end is not proof of correct full-throttle operation.
  • These are retained offline service instructions, not a performed adjustment, engine actuation or a substitute for the machine-specific general safety and repair instructions.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 5 · TI 24/2002, p. 7 · TI 24/2002, p. 8 — Section1.4.1 tensioner basic setting and complete1.4.4 including diagrams.

No additional parts-table entry added.

Service note · FS 75

FS 75: loop-handle control and throttle cable must change together

Model-specific introduction X 36 981 252; never exchange the handle alone.

X 36 981 252 — FS 75 loop-handle matched control/cable introduction only; not a general model range.

  • For FS 75 LOOP-HANDLE machines, the new master control is introduced FROM X 36 981 252. This is a model-conditioned modification cutoff, not a model-identification or production range. Other models in the bulletin have different cutoffs.
  • Old and new master controls can ONLY BE INTERCHANGED TOGETHER WITH THE COMPLETE THROTTLE CABLE. Complete control 4133 790 1301→4137 790 1310 and cable 4133 180 1105→4137 180 1105 form the matched conversion. The source does not authorize mixing individual former/new internals.
  • New grip has soft comfort zones and a top-mounted slide control. The cable integrates the electrical stop/ground function and is replaceable for repairs; fewer service parts and T20 housing screws are source features. DO NOT START THE ENGINE WITH THE HANDLE GRIPS DISASSEMBLED: risk of electric shocks.
  • Table former complete control includes items 1–21; new includes 1–12. This printed range is retained even though item 11 has no new-version entry. Former cable includes 24,25,28–30; new includes 26 and 31. Remark 1 keeps former complete control and cable available; not stock exhaustion.
  • Only the six explicitly listed LOOP-HANDLE configurations. No extension to bicycle handles, HT70, HL75K or separately named R/T/RX variants from a shared catalog heading. Later exact-model sheets are marked 24/2002 and contain 1350/1101/0801 and 1103/1150 revisions; they locate the subsystem, not prove equivalence to the 1997 configuration.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 37/1997, p. 1 · TI 37/1997, p. 2 · TI 37/1997, p. 3 — Pages 1–3 model-qualified introduction, matched conversion, features and complete-assembly table.

Part numbers (4)
  • 4133 790 1301 — Former complete master controlStill available; includes items 1–21 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 790 1310 — New complete master controlIncludes items 1–12 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4133 180 1105 — Former complete throttle cableStill available; includes 24,25,28–30 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 180 1105 — New complete throttle cableIncludes 26,31 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies

Service note · FS 80

FS 80: loop-handle control and throttle cable must change together

Model-specific introduction X 36 942 929; never exchange the handle alone.

X 36 942 929 — FS 80 loop-handle matched control/cable introduction only; not a general model range.

  • For FS 80 LOOP-HANDLE machines, the new master control is introduced FROM X 36 942 929. This is a model-conditioned modification cutoff, not a model-identification or production range. Other models in the bulletin have different cutoffs.
  • Old and new master controls can ONLY BE INTERCHANGED TOGETHER WITH THE COMPLETE THROTTLE CABLE. Complete control 4133 790 1301→4137 790 1310 and cable 4133 180 1105→4137 180 1105 form the matched conversion. The source does not authorize mixing individual former/new internals.
  • New grip has soft comfort zones and a top-mounted slide control. The cable integrates the electrical stop/ground function and is replaceable for repairs; fewer service parts and T20 housing screws are source features. DO NOT START THE ENGINE WITH THE HANDLE GRIPS DISASSEMBLED: risk of electric shocks.
  • Table former complete control includes items 1–21; new includes 1–12. This printed range is retained even though item 11 has no new-version entry. Former cable includes 24,25,28–30; new includes 26 and 31. Remark 1 keeps former complete control and cable available; not stock exhaustion.
  • Only the six explicitly listed LOOP-HANDLE configurations. No extension to bicycle handles, HT70, HL75K or separately named R/T/RX variants from a shared catalog heading. Later exact-model sheets are marked 24/2002 and contain 1350/1101/0801 and 1103/1150 revisions; they locate the subsystem, not prove equivalence to the 1997 configuration.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 37/1997, p. 1 · TI 37/1997, p. 2 · TI 37/1997, p. 3 — Pages 1–3 model-qualified introduction, matched conversion, features and complete-assembly table.

Part numbers (4)
  • 4133 790 1301 — Former complete master controlStill available; includes items 1–21 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 790 1310 — New complete master controlIncludes items 1–12 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4133 180 1105 — Former complete throttle cableStill available; includes 24,25,28–30 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 180 1105 — New complete throttle cableIncludes 26,31 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies

Service note · FS 85

FS 85: loop-handle control and throttle cable must change together

Model-specific introduction X 36 944 054; never exchange the handle alone.

X 36 944 054 — FS 85 loop-handle matched control/cable introduction only; not a general model range.

  • For FS 85 LOOP-HANDLE machines, the new master control is introduced FROM X 36 944 054. This is a model-conditioned modification cutoff, not a model-identification or production range. Other models in the bulletin have different cutoffs.
  • Old and new master controls can ONLY BE INTERCHANGED TOGETHER WITH THE COMPLETE THROTTLE CABLE. Complete control 4133 790 1301→4137 790 1310 and cable 4133 180 1105→4137 180 1105 form the matched conversion. The source does not authorize mixing individual former/new internals.
  • New grip has soft comfort zones and a top-mounted slide control. The cable integrates the electrical stop/ground function and is replaceable for repairs; fewer service parts and T20 housing screws are source features. DO NOT START THE ENGINE WITH THE HANDLE GRIPS DISASSEMBLED: risk of electric shocks.
  • Table former complete control includes items 1–21; new includes 1–12. This printed range is retained even though item 11 has no new-version entry. Former cable includes 24,25,28–30; new includes 26 and 31. Remark 1 keeps former complete control and cable available; not stock exhaustion.
  • Only the six explicitly listed LOOP-HANDLE configurations. No extension to bicycle handles, HT70, HL75K or separately named R/T/RX variants from a shared catalog heading. Later exact-model sheets are marked 24/2002 and contain 1350/1101/0801 and 1103/1150 revisions; they locate the subsystem, not prove equivalence to the 1997 configuration.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 37/1997, p. 1 · TI 37/1997, p. 2 · TI 37/1997, p. 3 — Pages 1–3 model-qualified introduction, matched conversion, features and complete-assembly table.

Part numbers (4)
  • 4133 790 1301 — Former complete master controlStill available; includes items 1–21 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 790 1310 — New complete master controlIncludes items 1–12 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4133 180 1105 — Former complete throttle cableStill available; includes 24,25,28–30 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 180 1105 — New complete throttle cableIncludes 26,31 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies

Service note · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75

Loop-handle controls: 1997 component revisions and retained former spares

All control-table rows retained without implying individual interchange.

  • The page 2 exploded view and page 3 table describe the matched conversion, not a set of independently interchangeable substitutions. Old control 4133 790 1301 and new 4137 790 1310 must change together with the complete matching throttle cable. All six model cutoffs are recorded in separate model-specific notes.
  • Items 2,4–9 change from the listed former to new numbers. New-only rows are handle moulding 1, contact spring 3, M5x12 screws 10 and P4x16 screws 12. Former-only rows 11 and 13–21 remain spares under remark 1. Every other old numbered control row carrying remark 1 likewise remains available. No unprinted supersession, stock-exhaustion or modified-only availability inferred.
  • Quantities: two clamping collars; two new M5x12 screws versus two former M5x16; four new P4x16 versus four former BZ4x19 screws; four former square washers; two former connector tags. Former inner moulding 17 includes tags 18. Printed complete-control ranges are former 1–21 and new 1–12 despite new item 11 being blank; no missing screw invented.
  • DO NOT START WITH GRIP DISASSEMBLED: electrical-shock hazard. The separate service note preserves routing and different housing/clamp torques. Parts numbers and item labels are those of 1997, not replacement of the later IPL drawing rows.
  • Only the six explicitly listed LOOP-HANDLE configurations. No extension to bicycle handles, HT70, HL75K or separately named R/T/RX variants from a shared catalog heading. Later exact-model sheets are marked 24/2002 and contain 1350/1101/0801 and 1103/1150 revisions; they locate the subsystem, not prove equivalence to the 1997 configuration.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 37/1997, p. 2 · TI 37/1997, p. 3 — Pages 2–3 exploded view and all control component rows 1–21, quantities and remark 1.

Part numbers (28)
  • 4137 790 1100 — New handle mouldingItem 1 new · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4133 791 9400 — Former clamping collarItem 2; two; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 791 9400 — New clamping collarItem 2; two · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 442 1600 — Contact springItem 3 new · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 182 1705 — Former slide controlItem 4; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 182 1700 — New slide controlItem 4 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 182 4506 — Former torsion springItem 5; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 182 4501 — New torsion springItem 5 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 182 0806 — Former throttle trigger interlockItem 6; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 182 0800 — New throttle trigger interlockItem 6 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 182 1007 — Former throttle triggerItem 7; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 182 1000 — New throttle triggerItem 7 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 182 4507 — Former trigger torsion springItem 8; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 182 4500 — New trigger torsion springItem 8 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 791 0821 — Former outer handle mouldingItem 9; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 791 0800 — New outer handle mouldingItem 9 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 9022 341 0960 — New IS-M5x12 screwItem 10; two · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 9022 341 0980 — Former IS-M5x16 screwItem 11; two; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 9074 478 3025 — New IS-P4x16 screwItem 12; four · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 9074 478 3065 — Former IS-BZ4x19 screwItem 13; four; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 792 6100 — Former square washerItem 14; four; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 182 4705 — Former detent springItem 15; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 182 6210 — Former screwItem 16; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 790 1102 — Former inner handle mouldingItem 17 includes 18; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 791 5300 — Former connector tagItem 18; two; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 182 6205 — Former collar screwItem 19; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4126 182 4505 — Former torsion springItem 20; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 9417 003 7510 — Former spring nutItem 21; still available · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies

Service note · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75

Loop-handle throttle cable: electrical return and cut-to-length spares

Cable and metal housing replace separate stop leads; coil ground terminal is unused in this configuration.

  • In the NEW matched configuration, metal cable housing 5 and inner cable 6 take over the electrical function of the separate stop-switch leads. Contacts, contact springs 7 and cable-end leads connect slide control 2 to ignition module8 and engine ground 9. The COIL GROUND CONNECTION 10 REMAINS UNUSED; ground is established through cable 6/9 screwed onto the engine housing. This does not mean the ignition system may be left ungrounded. Numbers here belong to electrical figure 392TI016 KN, not the summary table.
  • DO NOT START THE ENGINE WITH HANDLE GRIPS DISASSEMBLED: risk of electric shocks. These electrical functions are why a mechanically similar cable or handle alone is not a proved substitution. No continuity specification, live test or generic rewiring instruction inferred.
  • Former cable 4133 180 1105 includes table 24,25,28–30 and remains available (remark 1). New 4137 180 1105 includes 26 and 31. Former leads 24/25 are480/565 mm; new lead 26 is 100 mm. All three are NOT SEPARATELY AVAILABLE and must be cut from unchanged 10 m lead 0751 010 1110 (27, remark 2). No individual lead part numbers invented.
  • Former conduit 30 is 170 mm; new conduit 31 is 185 mm. Neither is separately supplied: cut from unchanged 960 mm conduit 4203 711 7201 (32, remark 3). Former terminal sockets 0751 030 8953 (28, four) and sleeves 0751 030 8470 (29, three) have blank new columns and NO supply remark; do not apply remark 1 to them merely by proximity.
  • Only the six explicitly listed LOOP-HANDLE configurations. No extension to bicycle handles, HT70, HL75K or separately named R/T/RX variants from a shared catalog heading. Later exact-model sheets are marked 24/2002 and contain 1350/1101/0801 and 1103/1150 revisions; they locate the subsystem, not prove equivalence to the 1997 configuration.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 37/1997, p. 2 · TI 37/1997, p. 3 — Page 2 electrical schematic/warning; page 3 cable rows 22–32 and supply remarks 2/3.

Part numbers (6)
  • 4133 180 1105 — Former complete throttle cableStill available; includes 24,25,28–30 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4137 180 1105 — New complete throttle cableIncludes 26,31 · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 0751 010 1110 — 10 m lead stockItem 27 unchanged; cut 24–26 from this · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 0751 030 8953 — Former terminal socketItem 28; four; no supply remark assigned · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 0751 030 8470 — Former sleeveItem 29; three; no supply remark assigned · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies
  • 4203 711 7201 — 960 mm conduit stockItem 32 unchanged; cut 30–31 from this · Exact loop-handle configuration in TI37/1997; matched handle/cable restriction applies

Service note · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75

Loop-handle control service: cable routing and separate 1 Nm / 2 Nm fasteners

Original removal sequence, slide engagement and spring seating; no operation performed.

  • The bulletin restricts inspection, service and repair to specially trained, authorized personnel. DO NOT START THE MACHINE WHEN THE GRIP IS OPEN OR DISASSEMBLED: electric-shock hazard. This is historical reference guidance, not bench authorization.
  • Page 4 section 1: undo housing screws with T20 screwdriver 5910 890 2301 and remove moulding; remove torsion spring; lift throttle trigger with cable from peg; unhook cable from trigger; lift contact spring slightly to free cable; lift interlock and contact spring from peg; remove contact spring from interlock. Read the original three-column illustrations in sequence. Tool number is a procedure reference, not a replacement-part row.
  • Reassemble in reverse. Page 5 routing figure identifies throttle cable 1, contact spring 2, conduit 3 and insulator 4; all must be correctly seated/routed as drawn. Tighten these HOUSING SCREWS TO 1.0 Nm. This value is not the clamping-collar torque.
  • Page 5 section 2: first remove interlock as in section 1, pull slide control off moulding, undo clamping-collar screws with T27, remove moulding from shaft tube and remove torsion spring from peg. Reassemble in reverse. CLAMPING-COLLAR SCREWS TO 2 Nm. Slide-control groove1 must engage outer edge2 of moulding half; torsion spring 3 must rest in slide-control mount4. Do not exchange1 Nm and 2 Nm or carry either over to later revisions.
  • The source explicitly sends omitted service notes to the FS75/80/85, FC75 and HL75 repair manuals (printed items 5 and 7). Those exact supplementary manual procedures are not established in the retained owner manual inventory. The candidate named 01268-ht75 is a 2005-04 HT70/75 components manual, not authority for all five named models. This dependency remains a documented gap; the recorded TI steps are not a complete machine repair procedure. HT75 is in the bulletin cover list but not in that page 4 manual list.
  • All page 5 footer references (HL75 TI41.96; HT75 TI03.97; FS75 TI35.97; FS80/85 TI32.97; FC75 TI37.96) are previous-model bibliography, not extra interchange permissions. Original item numbers are local to each figure; page 5 routing1–4 and slide-control 1–4 refer to different components.
  • Only the six explicitly listed LOOP-HANDLE configurations. No extension to bicycle handles, HT70, HL75K or separately named R/T/RX variants from a shared catalog heading. Later exact-model sheets are marked 24/2002 and contain 1350/1101/0801 and 1103/1150 revisions; they locate the subsystem, not prove equivalence to the 1997 configuration.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 37/1997, p. 4 · TI 37/1997, p. 5 — Pages 4–5 complete service instructions and figures, manual dependency, torque scopes and footer.

No additional parts-table entry added.

Wrong number or missing part for the FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX? Report a correction →