← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section S · 16 of 25 · 24 parts

Bike handle USA, CDN, BR, PRC

Fits FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11101112131415161718192202122233456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (24)

PosPart numberDescriptionQty
1 4128 790 0304 Handle, right 1
2 9074 478 3025 Pan head self-tapping screw IS-P4x16 3
3 4128 182 1700 Slide control 1
4 4128 182 4201 Detent spring Fitment / change note → 1
5 4128 182 4502 Torsion spring Fitment / change note → 1
6 4128 182 6200 Collar screw 1
7 4128 182 4504 Torsion spring 1
8 4128 182 4500 Torsion spring 1
9 4128 182 1000 Throttle trigger 1
10 4128 182 4501 Torsion spring 1
11 4128 182 0800 Lockout lever 1
12 4128 793 3000 Slide Fitment / change note → 1
13 4128 791 3100 Spring Fitment / change note → 1
14 9214 320 0700 Lock nut M5 1
15 9022 346 1070 Spline screw IS-M5x30 1
16 9291 021 0120 Washer 5.3 1
17 4137 180 1109 Throttle cable Fitment / change note → 1
18 4137 790 1701 Handlebar → replaced by 4128 790 1701, 4128 790 1701 TI 9/2003 1
19 4128 791 0300 Handle, left 1
20 4137 791 6800 Clamp 1
21 4130 791 0606 Clamp 1
22 4137 791 0900 Clamp 1
23 9022 341 1380 Spline screw IS-M6x35 4
Not numbered on the diagram — assemblies, kits and options
— 4128 790 1309 Control handle 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 controls: coordinated retrofit and ground connector

The new control handle needs the new cable and, on earlier machines, an added ignition-module ground connector.

  • The new control handle may be installed on previous machine versions only with the new throttle cable and a retrofitted ignition-module connector 4137 405 1600. The control handle and throttle cable remain separate replacement assemblies; buying a handle does not include the cable.
  • The new cable assembly comprises corrugated tube, cable and sealed microswitch with permanently connected water-tight short-circuit wires. Its individual parts, including the microswitch, are not separately supplied. Two fully insulated wires run directly to the ignition module; black connects to the primary-circuit connector, blue to the ground connector. Earlier machines require that ground connector to be mounted as well.
  • The handle is identified by its slide slot and gray-shaded non-slip surfaces in the diagram. The slide control operates the sealed ignition microswitch. Squeezing the trigger to its stop takes up cable slack: the sheath is attached to the slide, whose spring-loaded detent arm travels along the notched track. Initial installation requires adjustment; the instruction-manual chapter is referenced, and section 1.4.4 supplies the adjustment procedure within this TI. No missing manual is needed to establish this stated procedure.
  • The unrestricted interchangeability statement in section 2 concerns rewind-starter parts, not these coordinated control-handle changes.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 2 · TI 24/2002, p. 3 · TI 24/2002, p. 4 — Section1 introduction,1.1–1.2, summary item1 and1.4.1 wiring.

Part numbers (1)
  • 4137 405 1600 — Ignition-module ground connectorRequired retrofit on earlier machines · Named models and handle configuration only; coordinated retrofit conditions apply

Service note · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 controls: USA-production serial cutoffs

FS 80, FS 85 and HT 75 have separate USA cutoffs; KM 85 R is from production start.

  • USA production: FS 80 from serial 2 55 972 256; FS 85 from 2 55 809 184; HT 75 from 2 55 809 912. These are control-handle/throttle-cable changeovers, not whole-model production ranges, worldwide cutoffs or starter-rope changeovers.
  • KM 85 R: since start of production. Other models: introduction in progress. No numerical cutoff is supplied for those other models. Do not substitute one named model’s serial for another, or infer a separate serial for FS 85 RT/RX.
  • The printed USA production heading is preserved for this introduction table; the TI does not establish introduction timing for other production locations.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 3 · TI 24/2002, p. 4 — Section1.3 introduction table and model-specific scope.

No additional parts-table entry added.

Conditional replacement · FS 80 / FS 85

FS 80 / FS 85: bike-handle control parts

New handle 4128 790 1301 and cable 4137 180 1109 are coordinated replacements, not a handle-only retrofit.

  • Bike-handled FS 80/85 only. Old control handle 4128 790 1300 includes summary items 4–7; new 4128 790 1301 includes 4,5,8–10. Item numbers here belong to the summary, not the installation drawing callouts.
  • Right handle 4128 790 0300 becomes 4128 790 0301 and detent spring 4128 182 4200 becomes 4128 182 4201. Old contact springs 4128 442 1600 and 4128 442 1605 have no new individual counterparts listed. New torsion spring 4128 182 4502, slide 4128 793 3000 and spring 4128 791 3100 are added.
  • Old cable 4137 180 1100 is replaced in the new arrangement by cable assembly 4137 180 1109, including the microswitch and short-circuit wires (item 13), which have no separate order number. All other parts remain as before.
  • Every previous part marked remark 1 remains available as a spare for older machines; this is not a statement that all old stock was discontinued. New handle installation on an old machine still requires the new cable and ignition-module connector 4137 405 1600. USA serial cutoffs are model-specific as separately recorded.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 2 · TI 24/2002, p. 3 · TI 24/2002, p. 4 — Section1.3 summary items2–13 and supply remarks1–2.

Part numbers (14)
  • 4128 790 1300 — Control handlePrevious; includes items4–7 · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 790 1301 — Control handleNew; includes4,5,8–10 · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 790 0300 — Right handlePrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 790 0301 — Right handleNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 182 4200 — Detent springPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 182 4201 — Detent springNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 442 1600 — Contact springPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 442 1605 — Contact springPrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 182 4502 — Torsion springNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 793 3000 — SlideNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4128 791 3100 — SpringNew · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 180 1100 — Throttle cablePrevious; spare retained · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 180 1109 — Throttle cable assemblyNew; includes non-separate microswitch/wires · Named models and handle configuration only; coordinated retrofit conditions apply
  • 4137 405 1600 — Ignition-module connectorCoordinated retrofit · Named models and handle configuration only; coordinated retrofit conditions apply

Service note · FS 80 / FS 85

FS 80 / FS 85: bike-handle cable and spring installation

Route blue then black; the spring’s straight end goes in front of the cable sleeve.

  • For bike-handled FS 80/85: seat the microswitch as illustrated. Push the blue ground wire into the channel first, then the black short-circuit wire, both to the channel end. Keep both wires fully in the channel and in the recess at the corrugated-tube attachment; neither may project. The source cross-references the second 1.4.3 illustration for this shared routing detail.
  • Press the cable into the slide until the ferrule snaps into place. Put the slide in the molding with its groove at the end of the slot: this is the basic adjustment position. Check the two wires between channel and corrugated tube.
  • Attach cable end sleeve 14 to trigger 15. Put the straight end of spring 16 in the trigger in front of the cable end sleeve; fit its ring-shaped part over pivot 17 at the lower end of the trigger. Fit the trigger and loop the spring around screw boss 18. This differs from the loop-handle instruction to put the straight end under the sleeve.
  • Check corrugated tube and slide position. Do not squeeze the throttle trigger until section 1.4.4 adjustment. Screw the moldings together without pinching wires, mount the handle on the handlebar, attach cable to carburetor, reassemble powerhead and secure cable in drive-tube retainers. Set and secure the handlebar in its required working position before adjusting.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 5 · TI 24/2002, p. 6 — Section1.4.2 all installation diagrams and steps; cross-reference1.4.3 wiring recess.

No additional parts-table entry added.

Service note · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KM 85 R / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 RT / FS 85 RX

TI 24 controls: throttle adjustment, rechecks and travel limit

Adjust only fully assembled in the working position; unresolved travel-limit slack requires a new cable.

  • The cable is no longer routinely adjusted at the tensioner. For correct semi-automatic operation, set its screw so visible thread lengths above and below are equal. If this basic setting does not allow satisfactory operation, the source permits a slight screw correction; no numerical thread length or number of turns is given.
  • Adjust only when the machine is completely and securely assembled, with handlebar and control handle in the normal operating position. Use a screwdriver to press down the slide and push it to the end of its slot. Then press the trigger interlock and squeeze the trigger fully: the slide moves away from the end and takes up slack automatically. Carburetor adjustment may then be necessary; the TI supplies no carburetor screw setting.
  • Correct cable adjustment is required at full throttle, starting throttle and idle. Recheck if the trigger was squeezed too early during handling/mounting, after service or repair, before carburetor readjustment, after a large bike-handlebar position change, after cable stretch, or if snagging force changed the slide position.
  • The travel limit is reached when the slide touches the opposite end of the slot but free play remains. With interlock depressed and trigger fully squeezed, check that the throttle-shaft lever touches the carburetor body. If not, readjust the tensioner to take up slack. If that does not remedy it, install a new throttle cable. Simply reaching the slot end is not proof of correct full-throttle operation.
  • These are retained offline service instructions, not a performed adjustment, engine actuation or a substitute for the machine-specific general safety and repair instructions.
  • Only the named TI 24/2002 models and handle configurations are covered. Shared IPL sheets do not extend this to FR 85, SP models, HL 75 K, unrestricted KM 85 or unrelated series 4112 FS 80. The printed FS 85 RT label is retained, not silently equated to catalog FS 85 T or FS 85 R. Supply statements are historical. No physical interchange test was performed.

Source: TI 24/2002, p. 5 · TI 24/2002, p. 7 · TI 24/2002, p. 8 — Section1.4.1 tensioner basic setting and complete1.4.4 including diagrams.

No additional parts-table entry added.

Wrong number or missing part for the FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX? Report a correction →