Stihl 4137 · Section X · 21 of 25 · 20 parts
Gear head FS 80, 80 R, 85, 85 R, 85 T, 85 RX
Fits FS 80.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (20)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4130 641 0305 | Gear housing Fitment / change note → | 1 |
| 2 | 9503 003 9850 | Grooved ball bearing 609 Fitment / change note → → replaced by 9503 003 9853 TI 46/2000 | 2 |
| 3 | not sold separately | Drive pinion not available as a separate item | 1 |
| 4 | not sold separately | Spur bevel gear not available as a separate item | 1 |
| 5 | 4130 642 0601 | Drive shaft Fitment / change note → | 1 |
| 6 | 9503 003 5190 | Grooved ball bearing 6001-2RS | 1 |
| 7 | 9456 621 3100 | Circlip 28x1.2 | 1 |
| 8 | 9503 003 9853 | Grooved ball bearing 609-2Z Fitment / change note → | 1 |
| 9 | 9455 621 0750 | Circlip 9x1 Fitment / change note → | 1 |
| 10 | 9456 621 2660 | Circlip 24x1.2 Fitment / change note → | 1 |
| 11 | 4119 713 6500 | Screw plug | 1 |
| 12 | 4137 710 3800 | Thrust plate | 1 |
| 13 | not sold separately | Guard washer not available as a separate item | 1 |
| 15 | 4130 713 1600 | Thrust washer Fitment / change note → | 1 |
| 16 | 4126 642 7600 | Collar nut M10x1 l/h thread | 1 |
| 17 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 Fitment / change note → | 2 |
| 18 | 4126 713 3100 | Rider plate | 1 |
| 19 | 0781 120 1117 | Gear lubricant 80 g option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4137 640 0100 | Gearhead Fitment / change note → | 1 |
| — | 4130 640 7301 | Set of pinions Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 44 / FS 74 / FS 80 / FS 85
FS 44 / 74 / 80 / 85: splined gearhead and matched thrust parts
FS 80/85 change at X 35 221 994; replacement supply includes the matching plate and washer.
X 35 221 994 — FS80 and FS85 production change only; FS74 in progress; FS44 replacement scope, not this serial cutoff.
- New gearhead replaces the original on FS 80 and FS 85 from X 35 221 994 to improve transmission of power. It is also a replacement for FS 44 and FS 74. The serial cutoff belongs ONLY to FS 80/85; FS 74 introduction is in progress. No extension to shared-sheet FS 36/40, FS 72/76, FS 75 or R/T/RX variants.
- Page1 comparison: old4130 640 0100 is 1:1.33 / 7900 rpm, two flats; new4137 640 0100 is 1:1.40 / 7500 rpm, splined. These are rated maximum OUTPUT-SHAFT speeds, NOT engine tuning settings. Drawing342TI009 GM contrasts the old two-flat connection on the left with splined shaft, plate and washer on the right.
- TI19/1996 page3, specifically for FS 44, instead prints7500 rpm for old4130 640 0100 and7000 rpm for new4130 640 0101. Preserve that source/model/assembly context and the differing figures; TI32 does not explicitly revoke the earlier FS 44 speed or authorize raising it. Do not collapse the two tables into one universal limit.
- New gearheads supplied ONLY TOGETHER WITH new thrust plate14 and thrust washer16. Plate14 includes protective washer15. Original plate4126 710 3800 and washer4126 713 1600 remain spares (remark2); old protective washer has no number and is not a spare (remark4). New protective washer4112 717 2801 is separately numbered. No mixed two-flat/splined assembly authorized.
- Old gearhead table includes1,2,4,6,8–16; new includes1,3,5,7–16. Old complete4130 640 0100 supplied only until factory stocks exhausted (remark1). All other parts as before; the table is not a complete independent IPL. Later FS74 and FS80/85 sheets retain4137 gearhead but list thrust plate4137 710 3800 rather than source4130 710 3801; no silent replacement of historical numbers or proof of supersession.
- Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.
Source: TI 32/1997, p. 1 · TI 32/1997, p. 2 · TI 32/1997, p. 3 — Sections1.1,1.3,1.4 and1.6 gearhead/thrust rows, drawing and supply.
Referenced bulletin evidence: TI 19/1996, p. 3 · TI 19/1996, p. 5 — Earlier FS44-specific speed comparison and assembly table.
Part numbers (7)
- 4130 640 0100 — Original gearhead, two-flat outputStock exhaustion · Only the exact model/configuration and restrictions of 1997-32
- 4137 640 0100 — New gearhead, splined outputSupplied with new thrust plate and washer · Only the exact model/configuration and restrictions of 1997-32
- 4126 710 3800 — Original thrust plate including protective washerRemains spare · Only the exact model/configuration and restrictions of 1997-32
- 4130 710 3801 — New thrust plate including item15Item14 · Only the exact model/configuration and restrictions of 1997-32
- 4112 717 2801 — New protective washerItem15; original not a spare · Only the exact model/configuration and restrictions of 1997-32
- 4126 713 1600 — Original thrust washerRemains spare · Only the exact model/configuration and restrictions of 1997-32
- 4130 713 1600 — New thrust washerItem16 · Only the exact model/configuration and restrictions of 1997-32
Service note · FS 44 / FS 74 / FS 80 / FS 85
FS 44 / 74 / 80 / 85: gear housing, retaining rings and DG screw torque
Only new gearhead 4137 640 0100 DG screws take 8.5 Nm (6.3 lbf.ft).
- Section1.5 specifies8.5 Nm (6.3 lbf.ft) ONLY for the DG screws, item3, in NEW gearhead4137 640 0100. This is not a torque for original IS-M5x20 screws or every fastener on these models. No torque inferred for a4130 640 0101 assembly.
- Items1–7: housing0300→0305; two9022 371 1020 IS-M5x20 screws replaced by two9075 478 4159 DG5x24 screws; ring22x1→24x1.2 and ring9.5x0.8→9.0x1.0. All original housing/screw/ring rows carry remark2, original remains spare. Continued spare supply does not authorize arbitrary mixing.
- Drawing393TI004 GM explicitly pairs screws2/3 and rings4/5,6/7. TI callouts are not current IPL positions. Lower shaft bearing, screw plug and collar nut are drawn without numbers in this abbreviated summary; no new number or deletion inferred. Model production/replacement scope follows section1.1, not the other models sharing an IPL sheet.
- Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.
Source: TI 32/1997, p. 1 · TI 32/1997, p. 2 · TI 32/1997, p. 3 — Sections1.5 and1.6: torque, all housing/screw/ring rows and drawing.
Part numbers (8)
- 4130 641 0300 — Original gear housingRemains spare · Only the exact model/configuration and restrictions of 1997-32
- 4130 641 0305 — New gear housingItem1 · Only the exact model/configuration and restrictions of 1997-32
- 9022 371 1020 — Original IS-M5x20 spline screw, twoItem2; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 9075 478 4159 — New DG5x24 spline screw, twoItem3; 8.5 Nm · Only the exact model/configuration and restrictions of 1997-32
- 9456 621 2440 — Original retainer ring22x1Item4; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 9456 621 2660 — New retainer ring24x1.2Item5 · Only the exact model/configuration and restrictions of 1997-32
- 9452 600 0750 — Original retainer ring9.5x0.8Item6; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 9455 621 0750 — New retainer ring9.0x1.0Item7 · Only the exact model/configuration and restrictions of 1997-32
Service note · FS 44 / FS 74 / FS 80 / FS 85
FS 44 / 74 / 80 / 85: coordinated bearings, pinion set and shaft
Two bearing positions change; pinions remain a set, not separate spare items.
- Bearing2Z item8:9507 003 8056→9503 003 9853. TWO item9 bearings:9507 003 8054→9503 003 9850. Do not merge these bearing positions or assume all use9853. Old bearing rows remain spares under remark2.
- Item10 pinion set4130 640 7300→4130 640 7301 consists of drive pinion11 and spur bevel gear12. Both individual rows have -*- and remark3: NOT AVAILABLE AS SEPARATE ITEMS. Drawing places10/11 on the input side and10/12 on the output side; these are two members of one set, not two different set numbers.
- Item13 output shaft4130 642 0610→4130 642 0601 accompanies the two-flat-to-splined change. Old shaft and old pinion set remain spares (remark2). These coordinated changes are not approval to mix individual pinions, ratios, shafts or bearings across designs. The serial/model restrictions are those of section1.1.
- Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.
Source: TI 32/1997, p. 1 · TI 32/1997, p. 2 · TI 32/1997, p. 3 — Section1.6 items8–13, drawing, quantities and supply.
Part numbers (8)
- 9507 003 8056 — Original grooved ball bearing2ZItem8; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 9503 003 9853 — New grooved ball bearing2ZItem8 · Only the exact model/configuration and restrictions of 1997-32
- 9507 003 8054 — Original grooved ball bearing, twoItem9; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 9503 003 9850 — New grooved ball bearing, twoItem9 · Only the exact model/configuration and restrictions of 1997-32
- 4130 640 7300 — Original set of pinionsItem10; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 4130 640 7301 — New set of pinionsItem10; includes11/12 · Only the exact model/configuration and restrictions of 1997-32
- 4130 642 0610 — Original output shaftItem13; remains spare · Only the exact model/configuration and restrictions of 1997-32
- 4130 642 0601 — New output shaftItem13; splined · Only the exact model/configuration and restrictions of 1997-32
Wrong number or missing part for the FS 80? Report a correction →