Stihl 4137 · Section S · 17 of 22 · 37 parts
Angle drive 0° - 90° (46.2000)
Fits HL 75, HL 75 K.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (37)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4230 640 0558 NLA | Gear housing Fitment / change note → | 1 |
| 2 | 9022 341 1300 | Spline screw IS-M6x20 | 2 |
| 3 | 4226 641 6500 | Screw plug | 1 |
| 4 | not sold separately | Set of pinions no longer available from factory | 1 |
| 5 | 9513 003 1920 | Needle cage 8x12x10 Fitment / change note → | 2 |
| 6 | 0000 958 1700 NLA | Washer 17x24x0.1 | 1 |
| 7 | not sold separately | Washer 9x15x0.2 not available as a separate item | 1 |
| 8 | 0000 958 2000 NLA | Washer 20x28x0.1 | 1 |
| 9 | 9503 003 5190 | Grooved ball bearing 6001-2RS Fitment / change note → | 2 |
| 10 | 9456 621 3100 | Circlip 28x1.2 | 1 |
| 11 | 9455 621 0850 | Circlip 10x1 | 1 |
| 12 | 4230 642 0405 | Drive pinion | 1 |
| 13 | 4230 641 9410 NLA | Bearing bushing Fitment / change note → | 1 |
| 14 | 9022 341 1163 NLA | Spline screw IS-M5x86 Fitment / change note → | 1 |
| 15 | 9645 945 7455 | O-ring 4.9x1.9 Fitment / change note → | 1 |
| 16 | 9485 648 0362 | Cup spring 15x5.2x0.7 | 4 |
| 17 | 0000 958 0527 | Washer Fitment / change note → | 1 |
| 18 | 4230 641 7400 | Cap Fitment / change note → | 1 |
| 19 | 9220 260 0700 | Hexagon nut M5 | 1 |
| 20 | 4230 647 7000 NLA | Plug Fitment / change note → | 1 |
| 21 | not sold separately | Gear housing no longer available from factory | 1 |
| 22 | 9503 003 0040 | Grooved ball bearing 609 Fitment / change note → | 1 |
| 23 | 9503 003 9854 | Grooved ball bearing 609-Z Fitment / change note → | 1 |
| 24 | 9456 621 2660 | Circlip 24x1.2 | 1 |
| 25 | 9455 621 0750 | Circlip 9x1 | 1 |
| 26 | 9645 945 7845 NLA | O-ring 30x3.5 Fitment / change note → | 1 |
| 27 | 4230 642 4610 NLA | Perforated strip Fitment / change note → | 1 |
| 28 | 9022 341 0950 | Spline screw IS-M5x10 Fitment / change note → | 2 |
| 29 | not sold separately | Lock housing no longer available from factory | 1 |
| 30 | 4230 642 9010 NLA | Screw sleeve Fitment / change note → | 1 |
| 31 | 4230 641 3110 NLA | Spring Fitment / change note → | 1 |
| 32 | 9291 021 3861 NLA | Washer 5.1x8.3x0.8 Fitment / change note → | 1 |
| 33 | 9460 624 0320 NLA | E-clip 3.2 Fitment / change note → | 1 |
| 34 | 4230 643 3500 NLA | Adjusting lever Fitment / change note → | 1 |
| 35 | 9022 341 1090 | Spline screw IS-M5x40 Fitment / change note → | 1 |
| 36 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 4 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | not sold separately | Gearhead 0°- 90° no longer available from factory | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HL 75
HL 75: nine-position 0–90° cutter head
The adjustable attachment weighs 2.3 kg (5.1 lb); that is not the weight of the complete machine.
- The adjustable cutter bar joins, rather than replaces, the existing straight and fixed 30° versions. Its nine detents are marked 1 to 9 over a 0° to 90° range relative to the drive shaft. No equal angular spacing or angle for each numeral is stated.
- Figure 389TI005 KN identifies sliding sleeve (1), adjusting lever (2) and quadrant (3). The historical instruction is to retract the sleeve, move the lever, release the sleeve and let its pin engage the nearest hole. The two arrows indicate adjustment movement; this is not a full operating or safety procedure.
- Figure 389TI004 KN shows the complete long-reach machine; the stated 2.3 kg applies only to the adjustable hedge-trimmer attachment. No conversion of a fixed head or powerhead compatibility beyond this HL 75 introduction is established.
- Historical TI 44/1998 names HL 75, series 4230. Notes are located on later HL 75/HL 75 K sheets under series 4137, but do not extend the TI to HL 75 K, FH, HL-KM or later 135° heads. Introduction is in progress; no serial cutoff or current stock is established.
Source: TI 44/1998, p. 1 — Full introduction, both figures, adjustment paragraph and attachment-only weight.
No additional parts-table entry added.
Historical fitment · HL 75
HL 75: original adjustable gearbox parts
Gearbox 4230 640 0110 includes items 1–25, not the separate blade housing and cover at 26–28.
- The table lists only new parts for the adjustable version, subject to its remarks. Other attachment parts remain those of the latest straight and 30° versions; the exploded drawing is not a complete new-parts inventory. Unnumbered carried-over parts are not assigned invented numbers.
- Pinion set 4230 640 7301 includes item 3. Repeated callouts in drawing 389ET008 GM show locations, not a textual order-quantity schedule. Item 4 appears twice in the blade-drive area. No quantities or extra kit contents are inferred from repetition.
- The later 46.2000 sheet leaves some historical parts unnumbered and lists a different cup spring and nut. TI 44/1998 identifies the historical parts even where a later row is blank; the blanks are not silently filled in the canonical IPL.
- O-ring 9645 945 7845 is described as 30x3 in this TI, but 30x3.5 in the later catalog. Preserve the size discrepancy; the common number does not verify either physical dimension. Later variants and revisions do not overwrite the 1998 roster.
- Historical TI 44/1998 names HL 75, series 4230. Notes are located on later HL 75/HL 75 K sheets under series 4137, but do not extend the TI to HL 75 K, FH, HL-KM or later 135° heads. Introduction is in progress; no serial cutoff or current stock is established.
Source: TI 44/1998, p. 2 · TI 44/1998, p. 3 — Complete new-parts introduction and exploded figure; gearbox inclusion range and items 1–18.
Part numbers (19)
- 4230 640 0110 — Gearbox 0°–90°Assembly including items 1–25 · HL 75; exact 1998 variant and remark scope only
- 4230 640 0558 — Gearbox housingTI item 1 · HL 75; exact 1998 variant and remark scope only
- 4230 640 7301 — Pinion set; includes item 3TI item 2 · HL 75; exact 1998 variant and remark scope only
- 9513 003 1920 — Needle sleeve 8x12x10TI item 3 · HL 75; exact 1998 variant and remark scope only
- 9503 003 5190 — Ball bearing 6001 2RSTI item 4 · HL 75; exact 1998 variant and remark scope only
- 4230 641 9410 — Bearing bushTI item 5 · HL 75; exact 1998 variant and remark scope only
- 9022 341 1163 — Spline screw IS M5x86TI item 6 · HL 75; exact 1998 variant and remark scope only
- 9645 945 7455 — O-ring 4.9x1.9TI item 7 · HL 75; exact 1998 variant and remark scope only
- 9485 648 0303 — Cup spring 9x5.3x1TI item 8 · HL 75; exact 1998 variant and remark scope only
- 0000 958 0527 — WasherTI item 9 · HL 75; exact 1998 variant and remark scope only
- 4230 641 7400 — CapTI item 10 · HL 75; exact 1998 variant and remark scope only
- 9214 320 0700 — Locknut M5TI item 11 · HL 75; exact 1998 variant and remark scope only
- 4230 647 7000 — PlugTI item 12 · HL 75; exact 1998 variant and remark scope only
- 4230 641 0315 — Gearbox housingTI item 13 · HL 75; exact 1998 variant and remark scope only
- 9503 003 0040 — Ball bearing 609TI item 14 · HL 75; exact 1998 variant and remark scope only
- 9503 003 9854 — Ball bearing 609 ZTI item 15 · HL 75; exact 1998 variant and remark scope only
- 9645 945 7845 — O-ring 30x3TI item 16 · HL 75; exact 1998 variant and remark scope only
- 4230 642 4610 — QuadrantTI item 17 · HL 75; exact 1998 variant and remark scope only
- 9022 341 0950 — Spline screw IS M5x10TI item 18 · HL 75; exact 1998 variant and remark scope only
Historical fitment · HL 75
HL 75: sliding-sleeve assembly and separate lever
Sleeve assembly 4230 640 4510 includes items 19–23; lever 24 and screw 25 are outside that subassembly.
- Page 3 explicitly gives the sleeve assembly inclusion range 19–23. The outer gearbox assembly includes items 1–25, so the lever and screw belong to that larger range, not to the sleeve subassembly.
- Drawing 389ET008 GM shows the spring, washer and retaining ring in the sleeve stack. The historical retaining ring is 3.2, not the later snap-ring specification. No installation torque, preload, free spring length or interchangeable later sleeve is stated.
- The later 46.2000 sheet retains lever 4230 643 3500 and screw 9022 341 1090, but leaves its lock-housing order number blank. Later 24.2005 rows use other lever/lock parts; this TI does not authorize substituting them.
- Historical TI 44/1998 names HL 75, series 4230. Notes are located on later HL 75/HL 75 K sheets under series 4137, but do not extend the TI to HL 75 K, FH, HL-KM or later 135° heads. Introduction is in progress; no serial cutoff or current stock is established.
Source: TI 44/1998, p. 2 · TI 44/1998, p. 3 — Exploded sleeve stack and complete table items 19–25, including assembly line.
Part numbers (8)
- 4230 640 4510 — Sliding sleeve assemblyIncludes items 19–23 · HL 75; exact 1998 variant and remark scope only
- 4230 641 5510 — Sliding sleeveTI item 19 · HL 75; exact 1998 variant and remark scope only
- 4230 642 9010 — Screw sleeveTI item 20 · HL 75; exact 1998 variant and remark scope only
- 4230 641 3110 — SpringTI item 21 · HL 75; exact 1998 variant and remark scope only
- 9291 021 3861 — WasherTI item 22 · HL 75; exact 1998 variant and remark scope only
- 9460 624 0320 — Retaining ring 3.2TI item 23 · HL 75; exact 1998 variant and remark scope only
- 4230 643 3500 — Adjusting leverTI item 24 · HL 75; exact 1998 variant and remark scope only
- 9022 341 1090 — Spline screw IS M5x40TI item 25 · HL 75; exact 1998 variant and remark scope only
Conditional replacement · HL 75
HL 75: three bearings also replace fixed-30° parts
Only items 4, 14 and 15 carry the bearing replacement remark for the 30° gearbox.
- Remark 1 applies to 6001 2RS bearing 9503 003 5190 (item 4), 609 bearing 9503 003 0040 (item 14), and 609 Z bearing 9503 003 9854 (item 15). Each is also to be used as a replacement for the gearbox of the fixed 30° version.
- This remark is not permission to install the entire adjustable gearbox, pinion set, quadrant or sleeve in a fixed head. It supplies no original bearing numbers or reverse-interchange assertion.
- The later 30° catalog lists different 609-family numbers, including 9850 and 9853; this historical remark does not collapse 609, 609 Z and 609-2Z into universal equivalents. Keep exact source numbers and bearing designations.
- Historical TI 44/1998 names HL 75, series 4230. Notes are located on later HL 75/HL 75 K sheets under series 4137, but do not extend the TI to HL 75 K, FH, HL-KM or later 135° heads. Introduction is in progress; no serial cutoff or current stock is established.
Source: TI 44/1998, p. 2 · TI 44/1998, p. 3 — Item-specific remark 1 on rows 4,14,15; full remarks block.
Part numbers (3)
- 9503 003 5190 — Ball bearing 6001 2RSRemark 1: also replacement for fixed 30° gearbox · HL 75; exact 1998 variant and remark scope only
- 9503 003 0040 — Ball bearing 609Remark 1: also replacement for fixed 30° gearbox · HL 75; exact 1998 variant and remark scope only
- 9503 003 9854 — Ball bearing 609 ZRemark 1: also replacement for fixed 30° gearbox · HL 75; exact 1998 variant and remark scope only
Wrong number or missing part for the HL 75, HL 75 K? Report a correction →