Stihl 4140 · Section F · 6 of 28 · 18 parts
Muffler Cat.
Fits FS 55, FS 55 C, FS 55 R, FS 55 RC, FS 55 T.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (18)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4140 140 0653 | Muffler | 1 |
| 2 | 4140 141 9002 | Screen | 1 |
| 3 | 9099 021 0805 | Self-tapping screw 4.2x6.5 | 2 |
| 4 | 9022 421 0930 | Spline screw IS-M5x8 | 2 |
| 5 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 2 |
| 6 | 4140 149 0603 | Gasket Fitment / change note → | 1 |
| 7 | 4140 146 9000 | Insulating pad Fitment / change note → | 1 |
| 8 | 4140 140 7401 | Deflecting plate | 1 |
| 9 | 4140 149 0604 | Muffler gasket | 1 |
| 10 | 4140 145 1200 | Flange | 1 |
| 11 | 4140 149 0602 | Muffler gasket Fitment / change note → | 1 |
| 12 | 4140 140 0651 | Muffler | 1 |
| 13 | 1130 141 9001 | Screen → replaced by 4140 141 9002 TI 21/2003 | 1 |
| 14 | not sold separately | Cover plate not available as a separate item | 1 |
| 15 | 9099 021 0805 | Self-tapping screw 4.2x6.5 | 3 |
| 16 | 4140 149 0601 | Muffler gasket Fitment / change note → → replaced by 4140 149 0603 TI 36/2002 | 1 |
| 17 | 9075 478 4155 | Pan head self-tapping screw IS-D5x24 | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4140 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · HL 45 / FC 55 / FS 45 / FS 55 / KM 55
HL 45, FC 55, FS 45/55, KM 55: heat-resistant muffler gaskets
Revised gaskets and insulating mat for the muffler/catalytic-converter arrangement.
- Only the named HL 45, FC 55, FS 45, FS 55 and KM 55 configurations are covered, with the section-specific HL 45 exclusion below where stated. Shared IPL sheets do not extend this note to FS 38/46 or unnamed C/L/R/RC/T variants. HL 45 is headed series 4232; navigation through 4140 powerhead sheets is not series equivalence.
- New gaskets with higher temperature resistance replace 4140 149 0600 with 4140 149 0602 (drawing1) and 4140 149 0601 with 4140 149 0603 (drawing2). The previous gasket versions are no longer supplied by the factory.
- Insulating mat 4140 146 9000 (drawing3) is installed between the muffler and baffle plate to reduce radiated heat. Use the depicted muffler/catalytic-converter configuration; the TI does not say that every model or non-catalyst arrangement requires every item. Later separate ordinary/catalyst IPL sheets are navigation targets, not unrestricted combinations.
- Introduction is in progress, with no numerical serial cutoff. Factory availability is the historical 2002 statement, not current stock. Later IPL numbers do not overwrite historical numbers or prove unrestricted interchangeability. No hardware operation or fitment was tested.
Source: TI 36/2002, p. 2 · TI 36/2002, p. 3 — Section2 diagram and summary rows8–10/remark1.
Part numbers (5)
- 4140 149 0600 — Muffler gasketPrevious; deleted · Named models only; section-specific restrictions apply
- 4140 149 0602 — Heat-resistant gasketNew drawing1 · Named models only; section-specific restrictions apply
- 4140 149 0601 — Muffler/catalyst gasketPrevious; deleted · Named models only; section-specific restrictions apply
- 4140 149 0603 — Heat-resistant gasketNew drawing2 · Named models only; section-specific restrictions apply
- 4140 146 9000 — Insulating matBetween muffler and baffle plate · Named models only; section-specific restrictions apply
Wrong number or missing part for the FS 55, FS 55 C, FS 55 R, FS 55 RC, FS 55 T? Report a correction →