← Brushcutters & other equipment · series 4140

Stihl 4140 · Section C · 3 of 18 · 24 parts

Muffler

Fits HL 45.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213131414151516171818192202122222334567777889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (24)

PosPart numberDescriptionQty
1 4140 140 0609 Muffler 1
2 4140 140 0610 Muffler 1
3 4140 140 6903 Stub with screen 1
4 4140 140 0600 NLA Muffler 1
5 4140 140 0605 Muffler → replaced by 4140 140 0610 TI 23/2003 1
6 4140 140 6900 Stub with screen → replaced by 4140 140 6903 TI 23/2003 1
7 4140 149 0602 Muffler gasket Fitment / change note → 1
8 9075 478 4268 Pan head self-tapping screw IS-D5x60 2
9 4140 140 0653 Muffler 1
10 4140 141 9002 Screen 1
11 9099 021 0805 Self-tapping screw 4.2x6.5 2
12 9022 421 0930 Spline screw IS-M5x8 2
13 9075 478 4159 Pan head self-tapping screw IS-D5x24 2
14 4140 149 0603 Gasket Fitment / change note → 1
15 4140 146 9000 Insulating pad Fitment / change note → 1
16 4140 140 7401 Deflecting plate 1
17 4140 149 0604 Muffler gasket 1
18 4140 145 1200 Flange 1
19 4140 140 0651 Muffler 1
20 1130 141 9001 Screen → replaced by 4140 141 9002 TI 21/2003 1
21 not sold separately Cover plate not available as a separate item 1
22 9099 021 0805 Self-tapping screw 4.2x6.5 3
23 4140 084 6801 Spacer 1
Not numbered on the diagram — assemblies, kits and options
— 4140 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · HL 45 / FC 55 / FS 45 / FS 55 / KM 55

HL 45, FC 55, FS 45/55, KM 55: heat-resistant muffler gaskets

Revised gaskets and insulating mat for the muffler/catalytic-converter arrangement.

  • Only the named HL 45, FC 55, FS 45, FS 55 and KM 55 configurations are covered, with the section-specific HL 45 exclusion below where stated. Shared IPL sheets do not extend this note to FS 38/46 or unnamed C/L/R/RC/T variants. HL 45 is headed series 4232; navigation through 4140 powerhead sheets is not series equivalence.
  • New gaskets with higher temperature resistance replace 4140 149 0600 with 4140 149 0602 (drawing1) and 4140 149 0601 with 4140 149 0603 (drawing2). The previous gasket versions are no longer supplied by the factory.
  • Insulating mat 4140 146 9000 (drawing3) is installed between the muffler and baffle plate to reduce radiated heat. Use the depicted muffler/catalytic-converter configuration; the TI does not say that every model or non-catalyst arrangement requires every item. Later separate ordinary/catalyst IPL sheets are navigation targets, not unrestricted combinations.
  • Introduction is in progress, with no numerical serial cutoff. Factory availability is the historical 2002 statement, not current stock. Later IPL numbers do not overwrite historical numbers or prove unrestricted interchangeability. No hardware operation or fitment was tested.

Source: TI 36/2002, p. 2 · TI 36/2002, p. 3 — Section2 diagram and summary rows8–10/remark1.

Part numbers (5)
  • 4140 149 0600 — Muffler gasketPrevious; deleted · Named models only; section-specific restrictions apply
  • 4140 149 0602 — Heat-resistant gasketNew drawing1 · Named models only; section-specific restrictions apply
  • 4140 149 0601 — Muffler/catalyst gasketPrevious; deleted · Named models only; section-specific restrictions apply
  • 4140 149 0603 — Heat-resistant gasketNew drawing2 · Named models only; section-specific restrictions apply
  • 4140 146 9000 — Insulating matBetween muffler and baffle plate · Named models only; section-specific restrictions apply

Wrong number or missing part for the HL 45? Report a correction →