← FS 25-4, FS 65-4

Stihl 4170 · Section A · 1 of 14 · 31 parts

Crankcase

Fits FS 25-4, FS 65-4.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

This drawing carries 2 bore sizes — Ø 33 mm , Ø 39 mm . Not interchangeable — measure your cylinder before ordering. The catalogue lists them on one sheet for one machine and never says which variant each belongs to, so this guide does not either.

Position —

Go to table row → Where else is this used →
11101112131415161718192202021222324252627283456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (31)

PosPart numberDescriptionQty
1 4170 020 2101 Crankcase 1
1 4170 020 2100 Crankcase 1
1 4170 020 2112 Crankcase 1
2 9022 341 1010 Spline screw IS-M5x18 6
3 4170 021 1100 Cover 1
4 9022 341 1120 Spline screw IS-M5x58 4
5 4170 141 4100 Diaphragm 1
6 4170 141 2400 Support plate 1
7 4170 141 8100 Screw 1
8 4170 007 1002 Crankshaft with flywheel 1
9 4170 030 0403 Crankshaft 1
10 4170 030 2001 Piston Ø 33 mm 1
11 4170 034 3050 Set of piston ring 1
12 4170 034 1500 Piston pin 1
13 4170 400 1201 Flywheel 1
14 4170 007 1003 Crankshaft with flywheel 1
15 4170 030 0413 Crankshaft 1
16 4170 030 2011 Piston Ø 39 mm 1
17 4170 034 3055 Set of piston ring 1
18 4170 034 1510 Piston pin 1
19 4170 400 1211 Flywheel 1
20 4170 021 5600 Sealing ring 2
20 4170 021 5600 Sealing ring 1
21 4170 021 5601 Sealing ring 1
22 4170 029 0505 Gasket 1
23 4170 028 0300 Dipstick 1
24 4170 038 0700 Washer 1
25 4170 038 0300 Screw 1
26 4170 400 7000 Spark plug 1
27 4170 021 3702 Guard 1
28 9022 313 0650 Spline screw IS-M4x10 2

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 25-4 / FS 65-4

FS 25-4 / FS 65-4: four-stroke layout and oil-mist lubrication

Separate oil-tank lubrication and automatic decompression are described; these are not 4-MIX instructions.

  • Page 1 introduces nominal 22cc and31cc four-strokes for occasional users, landscape gardeners, local governments and farmers; typical applications are weeds/reed, wild growth/shrubs/bushes and thinning woody scrub/hedges/brushwood. Relatively quiet/pleasant sound and optimized compact weight/size are source descriptions, not independently measured comparisons. The three photographs show bike handle and loop handles with/without barrier bar; photos do not approve a cutting combination beyond section 3.
  • The shaft and gearhead are FROM FS 85. This is a component-origin statement, not permission to exchange every FS 85 shaft/gearhead variant. No exact part numbers or installation adaptations are given. A rigid drive shaft runs in the drive tube.
  • Sections1.1.1–1.1.3: single-cylinder engine; cylinder and crankcase form a single unit split along the longitudinal crankshaft axis. Piston has a special wear-resistant coating. Engine photo and exploded crankcase drawing supply construction context, not unprinted dimensions or coating material. OHV cross-flow head has exhaust valve(1) and inlet valve(2) opposite one another; polymer cam(3), follower(4), pushrod(5), rocker arm(6) operate the valves.
  • Section 1.1.4 is headed engine lubrication with centrifugal pump. Oil slinger plate(2) is PRESS-FITTED on crankshaft(1), atomizing oil in tank(3); piston movement pumps mist. DOWNWARD piston motion increases crankcase pressure, OPENS diaphragm valve(4) and feeds crankshaft/valve gear. UPWARD motion creates depression, CLOSES valve(4), and draws mist through return oilways to the tank. Diagram arrows show mist direction, not a fuel path.
  • Crankshaft bore(5) and end of return pipe(6) are central in the oil tank and, per source, remain above oil level at every machine angle when stopped. Oil remains in the tank until the rotating slinger atomizes it; this is the stated basis for all-position operation, not permission to overfill. Diagram label 7 has no textual component identification; none is invented.
  • Section 1.1.5 drawings distinguish cranking and idle: decompression cam(1) extends valve opening at CRANKING RPM, reducing compression and pull effort; spring(3) holds lever(2) against its stop. At IDLE centrifugal force on lever(2) retracts the decompression cam into the timing cam, restoring normal valve timing. No compression-pressure test value or extra switching RPM is inferred from the arrows.
  • Section 1.2: all-position diaphragm carburetor with integral fuel pump, additional manual priming pump and idle screw; transparent fuel tank; oil-impregnated foam air filter; two clutch shoes. Section 1.3: multifunction handle with soft non-slip grip. No carburetor model, fuel recipe or universal later-engine procedure is supplied.
  • Historical TI14/1998, series 4170: FS 25-4 and FS 65-4 only, with stated handle restrictions. Not FS 25/FS 65 two-strokes or later 4-MIX engines. No serial cutoff or current-stock promise is supplied. No hardware operation was performed.

Source: TI 14/1998, p. 1 · TI 14/1998, p. 2 · TI 14/1998, p. 3 · TI 14/1998, p. 4 · TI 14/1998, p. 5 — Pages1–4 full introduction, photographs, construction/timing/lubrication/decompression diagrams and section 1.2; page 5 section 1.3.

No additional parts-table entry added.

Service note · FS 25-4 / FS 65-4

FS 25-4 / FS 65-4: original speeds, clearances and oil specification

Cold valve clearances, engine/output speeds and maximum oil quantity retain their distinct conditions.

  • Section 2 pairs FS 25-4 / FS 65-4 respectively: displacement 22.2 /31 cm³; bore 33 /39 mm; stroke 26 /26 mm; power to ISO 8893 0.6 kW (0.8 bhp) /0.85 kW (1.2 bhp). Nominal22cc on page 1 does not replace22.2 cm³ specification.
  • Both models: maximum ENGINE speed 11,500 rpm; maximum OUTPUT SHAFT (tool mounting) speed 9,300 rpm; idle 3,100 rpm; clutch engagement 4,200 rpm. These are four different quantities, not interchangeable tachometer targets or a live test instruction.
  • Valve clearance with ENGINE COLD: inlet 0.10–0.14 mm; exhaust 0.13–0.17 mm. No hot-engine clearance or adjustment procedure is supplied here.
  • Engine lubrication: multigrade SAE 15 W40, class SG or SF, capacity MAXIMUM 100 ml. This is separate engine oil, not a fuel/oil mixing ratio; no substitute modern specification or fill/check method is inferred.
  • Fuel tank: FS 25-4 0.45 l (450 cm³); FS 65-4 0.65 l (650 cm³). Weight WITHOUT CUTTING TOOL AND DEFLECTOR: FS 25-4 loop 6.2 kg, bike 6.4 kg; FS 65-4 loop 6.4 kg, bike 6.6 kg. Do not label these complete cutting-ready weights or infer other exclusions.
  • Historical TI14/1998, series 4170: FS 25-4 and FS 65-4 only, with stated handle restrictions. Not FS 25/FS 65 two-strokes or later 4-MIX engines. No serial cutoff or current-stock promise is supplied. No hardware operation was performed.

Source: TI 14/1998, p. 5 — Page 5 complete engine, lubrication, tank and weight specification tables.

No additional parts-table entry added.

Historical fitment · FS 25-4 / FS 65-4

FS 25-4 / FS 65-4: piston orientation and service-tool limits

Piston crown arrow faces the inlet; press sleeves remain model-specific.

  • Page 7 section 5: service manual lists special servicing tools. Additional locking screw 4170 893 1200 blocks the crankshaft; illustration caption calls it a locking screw FOR PISTON. This describes one tool from two perspectives, not two tools or an installation-depth instruction. Retained tools/extras sheet does not list it; no catalog position is fabricated.
  • The piston installing tool consists of a PRESS ARBOR, PRESS SLEEVE 8 x31 for FS 25-4, PRESS SLEEVE 8 x29.5 for FS 65-4 and PISTON SUPPORT. No order numbers for these four components or measurement units for the sleeve notation are printed here; do not invent them or exchange the two sleeve sizes.
  • Section 6.1 and drawing 235TI010BL: arrow(1) on piston crown MUST POINT TO INLET SIDE. No exhaust-side orientation, ring-end location, torque or full piston-fitting procedure is inferred from the illustration.
  • Section 6 says the FS 25-4/FS 65-4 service manual is available but omits “Servicing the Carburetor”, “Troubleshooting” and standard-procedure repairs, covered in SEPARATE HANDBOOKS. This is a historical documentation scope statement, not proof that every required handbook is present or that the TI substitutes for them.
  • If started during repair/maintenance, ALL LOCAL AND NATIONAL SAFETY REGULATIONS and OWNER’S MANUAL precautions must be observed. This note provides no startup authorization or energized test procedure. Manual import/edition review remains in the follow-on phase.
  • Historical TI14/1998, series 4170: FS 25-4 and FS 65-4 only, with stated handle restrictions. Not FS 25/FS 65 two-strokes or later 4-MIX engines. No serial cutoff or current-stock promise is supplied. No hardware operation was performed.

Source: TI 14/1998, p. 7 — Page 7 full sections5–6.1, locking-screw and piston-arrow drawings.

Part numbers (1)
  • 4170 893 1200 — Locking screwService tool; not a machine spare · FS 25-4 / FS 65-4

Service note · FS 25-4 / FS 65-4

FS 25-4 / FS 65-4: historical workshop repair times

All 27 rows retain missing values and load-test footnotes; these are time allowances, not procedures.

  • Page 8 section 6.2: minutes for TRAINED PERSONNEL IN A PROPERLY EQUIPPED SERVICE WORKSHOP, one column covering both models. The table can be added to the STIHL repair-times table; no actual publication update is verified. Values are historical allowances, not guarantees, live measurements or repair instructions.
  • Rows 2,3,4,5,6 and9 print “---”: NO TIME GIVEN, never zero minutes or proof the repair is impossible. The asterisk means TEST RUN UNDER LOAD on rows 2,3,4,6,7 and10; retain it even where the allowance is missing. Unstarred rows saying test run are not silently given the starred load condition.
  • Row 1: Remove and refit engine — 15 minutes.
  • Row 2: Crankcase, pressure test* — --- (no time given).
  • Row 3: Crankshaft, bearings, pressure test* — --- (no time given).
  • Row 4: Sealing rings, pressure test* — --- (no time given).
  • Row 5: Crankcase leakage test, test run — --- (no time given).
  • Row 6: Cylinder, piston, pressure test* — --- (no time given).
  • Row 7: Ignition system, contact* — 15 minutes.
  • Row 8: Fuel supply, tank vent, test run — 10 minutes.
  • Row 9: Manifold or flange, pressure test — --- (no time given).
  • Row 10: Carburetor, check* — 25 minutes.
  • Row 11: Bike handle and throttle control — 10 minutes.
  • Row 12: Rewind starter, test run — 15 minutes.
  • Row 13: Clutch, test run — 20 minutes.
  • Row 14: Muffler — 10 minutes.
  • Row 15: Air filter — 5 minutes.
  • Row 16: Stop switch, test run — 10 minutes.
  • Row 17: Clutch housing — 20 minutes.
  • Row 18: Drive tube — 25 minutes.
  • Row 19: Replace gearhead or bearing housing — 5 minutes.
  • Row 20: Limit stop or deflector — 10 minutes.
  • Row 21: Drive shaft — 15 minutes.
  • Row 22: Fuel tank — 5 minutes.
  • Row 23: Check compression pressure — 5 minutes.
  • Row 24: Adjust valve clearance — 20 minutes.
  • Row 25: Replace crankcase, bottom half — 100 minutes.
  • Row 26: Replace crankshaft — 100 minutes.
  • Row 27: Replace cylinder, piston — 120 minutes.
  • Footer©1998 Andreas Stihl, D1/MTK-st Technical Documentation6276 and scissors symbol are bibliographic/cut-out context, not additional service instructions.
  • Historical TI14/1998, series 4170: FS 25-4 and FS 65-4 only, with stated handle restrictions. Not FS 25/FS 65 two-strokes or later 4-MIX engines. No serial cutoff or current-stock promise is supplied. No hardware operation was performed.

Source: TI 14/1998, p. 8 — Page 8 complete section 6.2,27 rows, units/workshop precondition, asterisk and footer.

No additional parts-table entry added.

Wrong number or missing part for the FS 25-4, FS 65-4? Report a correction →