Stihl 4170 · Section B · 2 of 14 · 23 parts
Valve timing gear
Fits FS 25-4, FS 65-4.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (23)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4170 025 1800 | Inlet valve | 1 |
| 1 | 4170 025 1810 | Inlet valve | 1 |
| 2 | 4170 025 1900 | Exhaust valve | 1 |
| 3 | 4170 025 1600 | Valve spring | 2 |
| 4 | 4170 025 1700 | Valve spring retainer | 2 |
| 5 | 4170 038 0800 | Pin 4x28 | 1 |
| 6 | 4170 038 1000 | Rocker arm | 2 |
| 7 | 4170 038 1100 | Grub screw | 2 |
| 8 | 4170 038 1200 | Hexagon nut | 2 |
| 9 | 4170 038 0100 | Pushrod | 2 |
| 10 | 4170 038 0805 | Pin 5x23.8 | 2 |
| 11 | 4170 030 3000 | Cam | 1 |
| 12 | 4170 038 0900 | Valve lifter | 2 |
| 13 | 4170 038 1300 | Cover | 1 |
| 13 | 4170 038 1310 | Cover | 1 |
| 14 | 9022 313 0680 | Spline screw IS-M4x16 | 5 |
| 15 | 4170 029 0500 | Gasket | 1 |
| 16 | 4170 020 1000 | Valve cover | 1 |
| 17 | 4170 021 2100 | Sleeve | 2 |
| 18 | 9022 313 1030 | Spline screw IS-M5x23 | 2 |
| 19 | 4170 021 2105 | Sleeve | 1 |
| 20 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 1 |
| 21 | 4170 021 3701 | Guard | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 25-4 / FS 65-4
FS 25-4 / FS 65-4: four-stroke layout and oil-mist lubrication
Separate oil-tank lubrication and automatic decompression are described; these are not 4-MIX instructions.
- Page 1 introduces nominal 22cc and31cc four-strokes for occasional users, landscape gardeners, local governments and farmers; typical applications are weeds/reed, wild growth/shrubs/bushes and thinning woody scrub/hedges/brushwood. Relatively quiet/pleasant sound and optimized compact weight/size are source descriptions, not independently measured comparisons. The three photographs show bike handle and loop handles with/without barrier bar; photos do not approve a cutting combination beyond section 3.
- The shaft and gearhead are FROM FS 85. This is a component-origin statement, not permission to exchange every FS 85 shaft/gearhead variant. No exact part numbers or installation adaptations are given. A rigid drive shaft runs in the drive tube.
- Sections1.1.1–1.1.3: single-cylinder engine; cylinder and crankcase form a single unit split along the longitudinal crankshaft axis. Piston has a special wear-resistant coating. Engine photo and exploded crankcase drawing supply construction context, not unprinted dimensions or coating material. OHV cross-flow head has exhaust valve(1) and inlet valve(2) opposite one another; polymer cam(3), follower(4), pushrod(5), rocker arm(6) operate the valves.
- Section 1.1.4 is headed engine lubrication with centrifugal pump. Oil slinger plate(2) is PRESS-FITTED on crankshaft(1), atomizing oil in tank(3); piston movement pumps mist. DOWNWARD piston motion increases crankcase pressure, OPENS diaphragm valve(4) and feeds crankshaft/valve gear. UPWARD motion creates depression, CLOSES valve(4), and draws mist through return oilways to the tank. Diagram arrows show mist direction, not a fuel path.
- Crankshaft bore(5) and end of return pipe(6) are central in the oil tank and, per source, remain above oil level at every machine angle when stopped. Oil remains in the tank until the rotating slinger atomizes it; this is the stated basis for all-position operation, not permission to overfill. Diagram label 7 has no textual component identification; none is invented.
- Section 1.1.5 drawings distinguish cranking and idle: decompression cam(1) extends valve opening at CRANKING RPM, reducing compression and pull effort; spring(3) holds lever(2) against its stop. At IDLE centrifugal force on lever(2) retracts the decompression cam into the timing cam, restoring normal valve timing. No compression-pressure test value or extra switching RPM is inferred from the arrows.
- Section 1.2: all-position diaphragm carburetor with integral fuel pump, additional manual priming pump and idle screw; transparent fuel tank; oil-impregnated foam air filter; two clutch shoes. Section 1.3: multifunction handle with soft non-slip grip. No carburetor model, fuel recipe or universal later-engine procedure is supplied.
- Historical TI14/1998, series 4170: FS 25-4 and FS 65-4 only, with stated handle restrictions. Not FS 25/FS 65 two-strokes or later 4-MIX engines. No serial cutoff or current-stock promise is supplied. No hardware operation was performed.
Source: TI 14/1998, p. 1 · TI 14/1998, p. 2 · TI 14/1998, p. 3 · TI 14/1998, p. 4 · TI 14/1998, p. 5 — Pages1–4 full introduction, photographs, construction/timing/lubrication/decompression diagrams and section 1.2; page 5 section 1.3.
No additional parts-table entry added.
Service note · FS 25-4 / FS 65-4
FS 25-4 / FS 65-4: original speeds, clearances and oil specification
Cold valve clearances, engine/output speeds and maximum oil quantity retain their distinct conditions.
- Section 2 pairs FS 25-4 / FS 65-4 respectively: displacement 22.2 /31 cm³; bore 33 /39 mm; stroke 26 /26 mm; power to ISO 8893 0.6 kW (0.8 bhp) /0.85 kW (1.2 bhp). Nominal22cc on page 1 does not replace22.2 cm³ specification.
- Both models: maximum ENGINE speed 11,500 rpm; maximum OUTPUT SHAFT (tool mounting) speed 9,300 rpm; idle 3,100 rpm; clutch engagement 4,200 rpm. These are four different quantities, not interchangeable tachometer targets or a live test instruction.
- Valve clearance with ENGINE COLD: inlet 0.10–0.14 mm; exhaust 0.13–0.17 mm. No hot-engine clearance or adjustment procedure is supplied here.
- Engine lubrication: multigrade SAE 15 W40, class SG or SF, capacity MAXIMUM 100 ml. This is separate engine oil, not a fuel/oil mixing ratio; no substitute modern specification or fill/check method is inferred.
- Fuel tank: FS 25-4 0.45 l (450 cm³); FS 65-4 0.65 l (650 cm³). Weight WITHOUT CUTTING TOOL AND DEFLECTOR: FS 25-4 loop 6.2 kg, bike 6.4 kg; FS 65-4 loop 6.4 kg, bike 6.6 kg. Do not label these complete cutting-ready weights or infer other exclusions.
- Historical TI14/1998, series 4170: FS 25-4 and FS 65-4 only, with stated handle restrictions. Not FS 25/FS 65 two-strokes or later 4-MIX engines. No serial cutoff or current-stock promise is supplied. No hardware operation was performed.
Source: TI 14/1998, p. 5 — Page 5 complete engine, lubrication, tank and weight specification tables.
No additional parts-table entry added.
Wrong number or missing part for the FS 25-4, FS 65-4? Report a correction →