← FS 25-4, FS 65-4

Stihl 4170 · Section C · 3 of 14 · 28 parts

Rewind starter, Ignition system

Fits FS 25-4, FS 65-4.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122233456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 4170 086 0500 Fanwheel 1
2 4170 195 0600 Starter cup 1
3 4170 195 0500 Starter cover 1
4 4170 195 3600 Sleeve 4
5 4170 195 3700 Bushing 1
6 4170 195 1600 Rewind spring 1
7 4170 195 0400 Rope rotor 1
8 4170 195 8205 Starter rope Ø 3x900 mm 1
9 4170 195 3400 Starter grip 1
10 4170 195 2000 Carrier 1
11 4170 195 3500 Spring 1
12 4170 195 9100 Screw 1
13 9022 341 1010 Spline screw IS-M5x18 4
14 4170 967 1500 Model plate 1
15 4170 967 1510 Model plate 1
16 4170 400 1300 Ignition module Fitment / change note → 1
17 not sold separately Hose 20 mm / 13/16'' not available as a separate item 1
18 9022 341 1010 Spline screw IS-M5x18 2
19 4170 440 1100 Short circuit wire 1
20 4170 036 8600 Woodruff key 1
21 4170 400 1200 Flywheel 1
21 4170 400 1210 Flywheel 1
22 4170 400 1201 Flywheel Fitment / change note → 1
22 4170 400 1211 Flywheel Fitment / change note → 1
23 9220 260 1100 Hexagon nut M8 1
23 9211 260 1360 Hexagon nut M10x1.25 1
Not numbered on the diagram — assemblies, kits and options
— 4170 190 4000 Rewind starter 1
— 0000 930 2208 NLA Starter rope Ø 3 mm x 30.5 m option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · FS 25-4

FS 25-4: series 4170 replacement ignition assignment

4170 400 1300 with flywheel 4170 400 1201; ignition lead not replaceable.

  • Printed series 4170. Use 4170 400 1300 with flywheel 4170 400 1201.
  • The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.

Part numbers (2)
  • 4170 400 1300 — Replacement ignition moduleAssigned component · FS 25-4, printed series 4170, listed combination only
  • 4170 400 1201 — Assigned flywheelRequired pairing · FS 25-4, printed series 4170

Historical fitment · FS 65-4

FS 65-4: series 4170 replacement ignition assignment

4170 400 1300 with flywheel 4170 400 1211; ignition lead not replaceable.

  • Printed series 4170. Use 4170 400 1300 with flywheel 4170 400 1211.
  • The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.

Part numbers (2)
  • 4170 400 1300 — Replacement ignition moduleAssigned component · FS 65-4, printed series 4170, listed combination only
  • 4170 400 1211 — Assigned flywheelRequired pairing · FS 65-4, printed series 4170

Wrong number or missing part for the FS 25-4, FS 65-4? Report a correction →