Stihl 4170 · Section O · 14 of 14 · 24 parts
Tools, Extras
Fits FS 25-4, FS 65-4.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (24)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4180 890 3400 | Combination wrench | 1 |
| 2 | 4130 893 7800 | Locking pin | 1 |
| 3 | 0000 890 2300 NLA | Screwdriver option | 1 |
| 4 | 4119 710 9001 | Full harness option | 1 |
| 5 | 4119 710 6306 | Backplate with strap | 1 |
| 6 | not sold separately | Strap 38x780mm / 1.5x30.7'' not available as a separate item | 1 |
| 7 | not sold separately | Strap 25 mm x 1.18 m / 1x46.5'' not available as a separate item | 1 |
| 8 | 4203 792 7200 | Slide | 3 |
| 9 | 4119 718 6300 | Slide | 1 |
| 10 | 4119 718 6310 | Slide | 2 |
| 11 | 4119 710 6400 | Buckle | 1 |
| 12 | 4119 718 7400 | Guard plate | 1 |
| 13 | 4119 710 6906 | Spring safety hook | 1 |
| 14 | 9408 021 4530 | Rivet shank 4x8x6 | |
| 15 | 9409 021 4420 | Rivet head 4x8 | |
| 16 | 4119 710 9012 | Harness | 1 |
| 17 | not sold separately | Strap 25 mm x 1.86 m / 1x73'' | 1 |
| 18 | 4119 718 6320 NLA | Slide | 1 |
| 19 | 0000 884 0307 | Safety glasses | 1 |
| 20 | 0000 891 0801 NLA | Tool roll option | 1 |
| 21 | 0783 830 2000 | Tube of sealant Dirko HT red option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 930 2242 | Webbing 38 mm x 5 m / 1.5x197'' not illustratedoption | 1 |
| — | 0000 930 2241 | Webbing 25 mm x 10 m / 1'' x 33' not illustratedoption | 1 |
| — | 4119 710 6406 | Buckle with strap | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · FS 25-4 / FS 65-4
FS 25-4 / FS 65-4: piston orientation and service-tool limits
Piston crown arrow faces the inlet; press sleeves remain model-specific.
- Page 7 section 5: service manual lists special servicing tools. Additional locking screw 4170 893 1200 blocks the crankshaft; illustration caption calls it a locking screw FOR PISTON. This describes one tool from two perspectives, not two tools or an installation-depth instruction. Retained tools/extras sheet does not list it; no catalog position is fabricated.
- The piston installing tool consists of a PRESS ARBOR, PRESS SLEEVE 8 x31 for FS 25-4, PRESS SLEEVE 8 x29.5 for FS 65-4 and PISTON SUPPORT. No order numbers for these four components or measurement units for the sleeve notation are printed here; do not invent them or exchange the two sleeve sizes.
- Section 6.1 and drawing 235TI010BL: arrow(1) on piston crown MUST POINT TO INLET SIDE. No exhaust-side orientation, ring-end location, torque or full piston-fitting procedure is inferred from the illustration.
- Section 6 says the FS 25-4/FS 65-4 service manual is available but omits “Servicing the Carburetor”, “Troubleshooting” and standard-procedure repairs, covered in SEPARATE HANDBOOKS. This is a historical documentation scope statement, not proof that every required handbook is present or that the TI substitutes for them.
- If started during repair/maintenance, ALL LOCAL AND NATIONAL SAFETY REGULATIONS and OWNER’S MANUAL precautions must be observed. This note provides no startup authorization or energized test procedure. Manual import/edition review remains in the follow-on phase.
- Historical TI14/1998, series 4170: FS 25-4 and FS 65-4 only, with stated handle restrictions. Not FS 25/FS 65 two-strokes or later 4-MIX engines. No serial cutoff or current-stock promise is supplied. No hardware operation was performed.
Source: TI 14/1998, p. 7 — Page 7 full sections5–6.1, locking-screw and piston-arrow drawings.
Part numbers (1)
- 4170 893 1200 — Locking screwService tool; not a machine spare · FS 25-4 / FS 65-4
Wrong number or missing part for the FS 25-4, FS 65-4? Report a correction →