Stihl 4201 · Section H · 8 of 22 · 48 parts
Carburetor HL-371A
Fits TS 350.
Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.
Parts (48)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4201 121 5402 | Valve jet | 1 |
| 2 | 4201 121 5401 | Valve jet Fitment / change note → | 1 |
| 3 | 1106 120 8801 | Inlet needle valve | 1 |
| 4 | 6503 129 2500 | Gasket | 1 |
| 5 | 1106 122 3005 | Spring | 1 |
| 6 | 1106 121 5000 | Inlet control lever | 1 |
| 7 | 1106 121 9200 | Spindle | 1 |
| 8 | 1110 122 7800 | Oval head screw | 1 |
| 9 | 6503 122 9410 | Plug | 1 |
| 10 | 6503 129 0910 | Gasket | 1 |
| 11 | 6503 121 4700 | Metering diaphragm | 1 |
| 12 | 6503 121 0500 | Pump housing | 1 |
| 13 | 1108 129 1100 | Gasket | 1 |
| 14 | 1106 121 4803 | Pump diaphragm | 1 |
| 15 | 6503 121 0400 | Top | 1 |
| 16 | 6503 122 7710 | Oval head screw | 6 |
| 17 | 6503 121 7810 | Strainer | 1 |
| 18 | 6503 129 3010 | Sealing ring | 1 |
| 19 | 4201 121 0802 | End cover | 1 |
| 20 | 6503 121 0800 | End cover | 1 |
| 21 | 6503 122 7700 | Oval head screw | 1 |
| 22 | 6503 122 9300 | Clip | 2 |
| 23 | 6503 122 7720 | Oval head screw | 2 |
| 24 | 1108 120 7010 | Throttle lever | 1 |
| 25 | 1106 122 7201 | Pan head screw | 2 |
| 26 | 4201 121 3310 | Throttle shutter | 1 |
| 27 | 1106 122 7400 | Round head screw | 2 |
| 28 | 9795 003 0350 | Threaded insert M5x7.5 | 2 |
| 30 | 6503 121 2910 | Choke shutter | 1 |
| 31 | 6503 122 3020 | Spring | 1 |
| 32 | 4201 122 6200 | Idle speed adjustment screw | 1 |
| 33 | 1110 129 3000 | Sealing ring | 1 |
| 34 | 4201 120 8705 | Control valve | 1 |
| 35 | 1106 129 3500 | Sealing ring | 2 |
| 36 | 1106 129 2300 | Gasket | 2 |
| 37 | 4201 122 3003 | Spring Fitment / change note → | 2 |
| 38 | 4201 122 6801 | Low speed adjustment screw Fitment / change note → | 1 |
| 39 | 4201 121 9400 | Ring, blue Fitment / change note → | 1 |
| 40 | 4201 121 2700 | Cap Fitment / change note → | 2 |
| 41 | 4201 122 6701 | High speed adjustment screw Fitment / change note → | 1 |
| 42 | 4201 121 9401 | Ring, red Fitment / change note → | 1 |
| 43 | 1108 122 3210 | Torsion spring | 1 |
| 44 | 1108 120 7100 | Throttle shaft with lever | 1 |
| 45 | 1108 121 3000 | Choke shaft | 1 |
| 46 | 1108 122 3201 | Torsion spring | 1 |
| 47 | 1108 120 7000 | Governor lever | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4201 120 0610 | Carburetor HL-371A | 1 |
| — | 4201 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 350
TS 350: discontinued ZAMA LA S6 A replaced by Tillotson
Complete ZAMA carburetor supply ends; its component spares remain available.
- TS 350 alternative-production ZAMA LA S6 A 4201 120 0602 is no longer installed or factory-supplied complete. Only Tillotson 4201 120 0604 is now installed on the production line and supplied as replacement for this model. Do not swap the separate TS 350 and TS 360 replacement numbers.
- Component parts of the ZAMA carburetors REMAIN available as spares. The prose says installation stopped some time ago, while the summary says in progress; no numeric introduction cutoff is provided. The bulletin points to the parts list for the equivalent Tillotson and supplies no tuning or internal-parts interchange procedure. Canonical sheet names do not establish the precise Tillotson variant suffix used in 1994.
- Historical TI09/1994 guidance for the named TS 350 / TS 360 models only; no successor or TS 350 AVE applicability inferred from a shared IPL sheet. Across-flats dimensions describe wrench sizes, not thread diameters. Factory stock statements are historical, not current availability. MOQ columns are commercial order quantities. No physical interchange test was performed.
Source: TI 9/1994, p. 6 — TS 350: discontinued ZAMA LA S6 A replaced by Tillotson.
Part numbers (2)
- 4201 120 0602 — ZAMA LA S6 A complete carburetororiginal; no longer supplied · TS 350: discontinued ZAMA LA S6 A replaced by Tillotson
- 4201 120 0604 — Tillotson replacement carburetormodel-specific replacement · TS 350: discontinued ZAMA LA S6 A replaced by Tillotson
Conditional replacement · TS 350
TS 350: HL366 replaces HL292G for the EPA change
Limited H/L adjustment and new valve jet accompany the continuous carburetor change.
- Historical TI05/1998 for TS 350, type 4201 only. Later 2012 IPL sheets are navigation/comparison, not evidence that later carburetor versions equal HL292G or HL366. No extension to TS 350 AVE, TS 360, other cut-off machines or saws. Historical availability is not current stock. No hardware operation was performed.
- Complete HL292G carburetor 4201 120 0604 is replaced by HL366 4201 120 0608 in this EPA modification. Both HIGH and LOW speed adjusting ranges are limited; this is not a fixed-jet carburetor without H adjustment.
- Page1 drawing 330TI012 KN identifies white knurled caps (1), red high-speed ring (2), H screw (3), blue low-speed ring (4), L screw (5) and the module with locating holes (6). Each ring has an integrally moulded connecting link; tabs inside the module holes act as stops. The cap knurl engages in the ring. These are FUNCTION callouts, not the page4 spare-part row numbers.
- New valve jet 4201 121 5401 is intended to optimize full-load running. Page3 drawing 330TI018 GM contrasts HL292G with HL366 and uses the SUMMARY callouts: spring1, low screw2, blue ring3, high screw4, red ring5, cap6 and valve jet7. Do not confuse module6 in the function diagram with cap6 in the summary.
- The change is introduced CONTINUOUSLY; no serial cutoff or whole-model production range is stated. Original HL292G remains available for machines WITHOUT EPA permit under remark1. This restriction is not the general non-EPA replacement rule from a different model.
- The later exact TS350 IPL has HL371A 4201 120 0610 and HL372A 4201 120 0611, not the HL366/HL292G complete assemblies specified here. Those sheets are comparison/navigation only; neither later type inherits the 1998 settings or interchange claims automatically.
Source: TI 5/1998, p. 1 · TI 5/1998, p. 3 · TI 5/1998, p. 4 — Section 1, section 1.1 function, comparative diagram and section 1.6 assembly rows/remarks.
Part numbers (3)
- 4201 120 0604 — Complete HL292G carburetorOriginal; retained for non-EPA machines · TS 350; only the carburetor/version and conditions stated here
- 4201 120 0608 — Complete HL366 carburetorNew EPA modification · TS 350; only the carburetor/version and conditions stated here
- 4201 121 5401 — Valve jetNew full-load metering part · TS 350; only the carburetor/version and conditions stated here
Conditional replacement · TS 350
TS 350: HL366 component assignments and non-EPA spares
Every summary row keeps its version column, including the old dual-purpose adjusting screw.
- Historical TI05/1998 for TS 350, type 4201 only. Later 2012 IPL sheets are navigation/comparison, not evidence that later carburetor versions equal HL292G or HL366. No extension to TS 350 AVE, TS 360, other cut-off machines or saws. Historical availability is not current stock. No hardware operation was performed.
- Row1 spring: 1106 122 3000 → 4201 122 3003. Row2 low-speed adjusting screw: 1108 122 6800 → 4201 122 6801. Remark2 explicitly says the ORIGINAL low-speed screw also served as the HIGH-speed adjusting screw; do not replace that fact with a later IPL high-screw number.
- New-only rows with original-column dashes: row3 BLUE ring 4201 121 9400, row4 HIGH-speed screw 4201 122 6701, row5 RED ring 4201 121 9401, row6 WHITE cap 4201 121 2700. A dash does not mean the old carburetor had no high-speed screw: original row2 and remark2 cover it.
- Row7 valve jet: 1106 121 5400 → 4201 121 5401. Original complete carburetor, spring, dual-purpose screw and valve jet carry remark1: they remain available for machines WITHOUT EPA permit. No unrestricted mixing of old and new internals is stated.
- Both assembly rows say each including the listed components, qualified by their version columns; new-only limiter parts are not implied to be fitted to HL292G. Other parts remain as before. Unnumbered special-tool row adds puller 5910 890 4500, not an installed carburetor component. Introduction is continuous.
- Later HL371A IPL lists the new spring, L/H screws, rings, cap and valve jet but under a different complete-carburetor type; HL372A lists the old spring/low screw and valve jet plus a separately numbered high screw. Shared component numbers do not establish identical complete carburetors or override the historical dual-purpose screw remark.
Source: TI 5/1998, p. 3 · TI 5/1998, p. 4 — Comparative drawing and section 1.6 seven numbered rows, special-tool row and both remarks.
Part numbers (10)
- 1106 122 3000 — SpringOriginal version; non-EPA spare · TS 350; only the carburetor/version and conditions stated here
- 4201 122 3003 — SpringNew HL366 version · TS 350; only the carburetor/version and conditions stated here
- 1108 122 6800 — Low-speed adjusting screwOriginal version; non-EPA spare · TS 350; only the carburetor/version and conditions stated here
- 4201 122 6801 — Low-speed adjusting screwNew HL366 version · TS 350; only the carburetor/version and conditions stated here
- 4201 121 9400 — Blue low-speed ringNew HL366 version · TS 350; only the carburetor/version and conditions stated here
- 4201 122 6701 — High-speed adjusting screwNew HL366 version · TS 350; only the carburetor/version and conditions stated here
- 4201 121 9401 — Red high-speed ringNew HL366 version · TS 350; only the carburetor/version and conditions stated here
- 4201 121 2700 — White capNew HL366 version · TS 350; only the carburetor/version and conditions stated here
- 1106 121 5400 — Valve jetOriginal version; non-EPA spare · TS 350; only the carburetor/version and conditions stated here
- 4201 121 5401 — Valve jetNew HL366 version · TS 350; only the carburetor/version and conditions stated here
Service note · TS 350
TS 350: HL366 capped standard setting is measured from lean
H and L each open one-quarter turn from the lean setting, not from their seats.
- Historical TI05/1998 for TS 350, type 4201 only. Later 2012 IPL sheets are navigation/comparison, not evidence that later carburetor versions equal HL292G or HL366. No extension to TS 350 AVE, TS 360, other cut-off machines or saws. Historical availability is not current stock. No hardware operation was performed.
- With caps/rings in place, H = 1/4 open and L = 1/4 open, measured FROM THE LEAN SETTING in each case. This is distinct from the cap-off seat-based basic setting. The TI reproduces the standard setting and says it matches the Owner’s Manual carburetor-adjustment chapter; it does not identify the manual edition.
- Allowed correction is up to 180° for LOW-speed screw L and 90° for HIGH-speed screw H. The TI says these limits permit a leaner mixture at higher altitude and prevent an over-rich mixture from exceeding EPA emission standards. The access drawing labels L, H and LA separately; the limiter drawing shows L on the left and H on the right with the two different arcs. Do not swap the travel limits.
- For unsatisfactory running at higher altitude, check the standard setting, warm up the engine and turn H CLOCKWISE (leaner). The source warns that TOO LEAN a mixture can damage the engine through insufficient lubrication and overheating. It provides no extra turns, maximum-speed target or permission to defeat the stops.
- The factory optimum-mixture, smooth-running, fuel-efficiency, reliability and low-emissions statements are vendor claims, not measurements performed here.
Source: TI 5/1998, p. 2 — Section 1.2 and adjustment drawings 330TI013/014 KN.
No additional parts-table entry added.
Service note · TS 350
TS 350: HL366 cap-off basic setting and single-use limiters
After screw refitting, H backs off 1½ turns and L 1⅝ turns from their seats.
- Historical TI05/1998 for TS 350, type 4201 only. Later 2012 IPL sheets are navigation/comparison, not evidence that later carburetor versions equal HL292G or HL366. No extension to TS 350 AVE, TS 360, other cut-off machines or saws. Historical availability is not current stock. No hardware operation was performed.
- To replace adjusting screws or clean this carburetor, remove CAPS AND RINGS using puller 5910 890 4500. Screw the puller into the cap COUNTERCLOCKWISE until cap and ring come off, as shown in 330TI015 KN. The removal direction is not the altitude-adjustment direction.
- Both caps AND rings are damaged during removal and MUST NOT BE REUSED. Replace both, rather than applying single-use wording only to the white cap.
- After refitting adjusting screws and WITHOUT caps/rings: the source says “With the adjusting screws hard against their seats”, H = back off 1 1/2 turns; L = back off 1 5/8 turns. Preserve that exact historical seat wording; no seating torque is specified and none is inferred. These are not the 1/4-turn lean-stop values of section1.2.
- Then fit NEW rings and caps using section1.3.1 alignment instructions. This is historical offline reference, not a hardware adjustment performed or verified here.
Source: TI 5/1998, p. 2 · TI 5/1998, p. 4 — Sections 1.3–1.3.1, puller drawing and special-tool row.
Part numbers (1)
- 5910 890 4500 — Limiter cap/ring pullerService tool; not installed part · TS 350; only the carburetor/version and conditions stated here
Service note · TS 350
TS 350: blue L ring, red H ring, then caps without shifting settings
Align ring marks and cap tabs exactly; LA sets 2,500 rpm with a tachometer.
- Historical TI05/1998 for TS 350, type 4201 only. Later 2012 IPL sheets are navigation/comparison, not evidence that later carburetor versions equal HL292G or HL366. No extension to TS 350 AVE, TS 360, other cut-off machines or saws. Historical availability is not current stock. No hardware operation was performed.
- After the cap-off basic setting, insert BLUE ring 4201 121 9400 over LOW-speed screw L: align markings and press the ring flush with the module edge. Insert RED ring 4201 121 9401 over HIGH-speed screw H the same way. Page3 drawing 330TI016 KN uses step1 for blue/L and step2 for red/H, not page4 part-row numbering.
- Align each WHITE cap 4201 121 2700 so its FLAT TAB projects exactly into the slit of its adjusting screw. DO NOT CHANGE the position of either rings or adjusting screws while positioning the caps. Press caps into rings with the carburetor screwdriver until they engage; no screwdriver part number or press force is supplied.
- Drawing 330TI017 KN marks both caps as step3. Once fitted, cap/ring/screw positions correspond to the STANDARD SETTING of section1.2; do not add another quarter-turn after assembly merely because the basic-setting values differ.
- Set idle to 2,500 rpm with idle-speed screw LA; USE A TACHOMETER. This is not an H-screw maximum-speed instruction. No maximum-speed figure or adjustment for HL371A/HL372A is supplied by this TI.
Source: TI 5/1998, p. 1 · TI 5/1998, p. 2 · TI 5/1998, p. 3 · TI 5/1998, p. 4 — Section 1.3.1 continuation, ring/cap diagrams, section 1.3.2 and part-color bindings.
Part numbers (3)
- 4201 121 9400 — Blue ringLow-speed L · TS 350; only the carburetor/version and conditions stated here
- 4201 121 9401 — Red ringHigh-speed H · TS 350; only the carburetor/version and conditions stated here
- 4201 121 2700 — White capNew cap on each adjusting screw · TS 350; only the carburetor/version and conditions stated here
Service note · TS 350
TS 350: EPA label, 50:1 mixture and missing TI27 reference
TI05 states the mixture used for the EPA permit but delegates further emission-system details.
- Historical TI05/1998 for TS 350, type 4201 only. Later 2012 IPL sheets are navigation/comparison, not evidence that later carburetor versions equal HL292G or HL366. No extension to TS 350 AVE, TS 360, other cut-off machines or saws. Historical availability is not current stock. No hardware operation was performed.
- The cover says these modifications achieve EPA compliance and the factory applies the illustrated U.S. EPA Phase1 label to conforming machines. Label 000TI013 KN contains engine-family/type/displacement/manufacture-date placeholders and refers to the Owner’s Manual for maintenance and adjustment. It is a label TEMPLATE, not identified machine data or a complete label order number.
- The EPA permit was obtained using a 50:1 fuel-oil mixture. Fuel details and Federal Emission Control Systems Utility Engines explicitly refer to TI27/1997. This source is absent from the retained690TIs and the bounded current766-PDF inventory, reverified in this batch. The delegated details remain a source gap, not invented warranty terms, emission measurements or legal permission.
- The carburetor standard, basic and idle settings are reproduced in this TI. The label refers generally to the Owner’s Manual without identifying its edition.
Source: TI 5/1998, p. 1 · TI 5/1998, p. 3 — Cover label, sections 1.4–1.5.
No additional parts-table entry added.
Wrong number or missing part for the TS 350? Report a correction →