Stihl 4201 · Section K · 10 of 22 · 14 parts
Connector
Fits TS 350.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (14)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 9490 000 7850 | Narrow V-belt 9.7x850 | 1 |
| 2 | 4201 701 0202 | Cast arm | 1 |
| 3 | 4201 708 8403 | Hexagon head screw M10x40 | 1 |
| 4 | 9220 260 1300 | Hexagon nut M10 | 2 |
| 5 | 4201 967 1504 | Model plate TS 350 Fitment / change note → | 1 |
| 6 | 0000 967 1517 | Model plate TS 350 not available as a separate item | 1 |
| 7 | 4201 967 1502 | Model plate TS 350 S Fitment / change note → | 1 |
| 8 | 0000 974 1000 | Round head rivet 3x6 Fitment / change note → | 2 |
| 9 | 9022 341 1300 | Spline screw IS-M6x20 | 2 |
| 10 | 4201 791 7604 | Support | 1 |
| 11 | 4201 790 1700 | Handlebar | 1 |
| 12 | 4201 791 9000 | Clamp | 1 |
| 13 | 9022 341 1400 | Spline screw IS-M6x40 | 3 |
| 14 | 0000 967 3702 | Warning pictogram TS | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 350
TS 350: model-specific raised machine support
New support improves stability and cutting-wheel ground clearance when the machine is set down.
- TS 350 machine support 4201 791 7601 changes to 4201 790 7600. TS 350 production introduction is in progress / the foreseeable future; no serial cutoff is supplied. The TS 360 cutoff does NOT apply to this model.
- Original support remains factory-supplied only while stocks last. Illustrated fitting instructions are supplied with each new support; this TI does not reproduce them. The two model-specific support pairs are not a cross-model interchange claim.
- Historical TI09/1994 guidance for the named TS 350 / TS 360 models only; no successor or TS 350 AVE applicability inferred from a shared IPL sheet. Across-flats dimensions describe wrench sizes, not thread diameters. Factory stock statements are historical, not current availability. MOQ columns are commercial order quantities. No physical interchange test was performed.
Source: TI 9/1994, p. 1 — TS 350: model-specific raised machine support.
Part numbers (2)
- 4201 791 7601 — Machine supportoriginal; while stocks last · TS 350: model-specific raised machine support
- 4201 790 7600 — Raised machine supportnew version · TS 350: model-specific raised machine support
Historical fitment · TS 350
TS 350: plastic nameplate requires countersunk cast arm
X 33 746 578; 4201 967 1502 → 4201 967 1504; original aluminium plate/rivet retained.
X 33 746 578 — TS 350 nameplate change only; cast arm must have countersunk holes.
- For TS 350, from machine number X 33 746 578, the riveted aluminium nameplate changes to clip-in plastic. It is pushed into the cast arm and held by TWO retaining lugs; mounting holes are countersunk. The other model has a different nameplate serial and location.
- Plastic nameplates CANNOT be fitted to the original cast arm or filter housing because those versions lack countersunk mounting holes. No field-drilling or countersinking conversion is authorized by this note; no hole dimensions, angle or substitute body is specified.
- The TS 350 table row changes 4201 967 1502 to 4201 967 1504. Original aluminium nameplates and round head rivets 0000 974 1000 (3 x 6) remain available for older machines. The new rivet cell is a dash, not deletion of original repair supply. No rivet quantity is printed.
- The opening paragraph and the separate table footer agree on the model-specific serial assignments in the original scan. Garbled extraction around the TS 360 parenthesis does not alter those assignments. This plate change does not imply the starter change occurred at the same number.
- Catalog navigation uses the exact-model TS 350 Connector sheet, where positions 5/7 list these plate numbers. The TI says the plate mounts in the cast arm; the sheet title is navigation, not a rewritten mounting location. The retained IPL calls old 4201 967 1502 “Model plate TS 350 S”, while this TI table calls it TS 350. Both labels are preserved; this unresolved variant-label difference is not proof that TS 350 S shares every change or that the canonical row is wrong.
- Historical TI 10/1996 evidence for TS 350 and TS 360, series 4201. Shared catalog sheets do not add TS 350 AVE, TS 510 or TS 760. No hardware operation was performed; factory availability is historical, not current stock. Starter and the two model-specific nameplate changeovers must remain separate.
Source: TI 10/1996, p. 2 — TS 350: plastic nameplate requires countersunk cast arm.
Part numbers (3)
- 4201 967 1502 — TS 350 original aluminium nameplateretained for older machines · TS 350; TI10/1996 specified configuration
- 4201 967 1504 — TS 350 plastic nameplaterequires modified countersunk cast arm · TS 350; TI10/1996 specified configuration
- 0000 974 1000 — Round head rivet 3 x6retained for original aluminium plate; quantity unspecified · TS 350; TI10/1996 specified configuration
Wrong number or missing part for the TS 350? Report a correction →