← Cut-off machines · series 4201

Stihl 4201 · Section L · 11 of 22 · 43 parts

Support with guard

Fits TS 350.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122232425262728293303132333435363744557889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (43)

PosPart numberDescriptionQty
1 4238 700 8110 Guard Ø 300 mm / 12'' 1
2 4224 700 8103 NLA Guard Ø 350 mm / 14'' → replaced by 4224 700 8102 TI 43/2007 1
3 4205 791 3902 Support 1
4 9456 621 3600 Circlip 32x1.2 2
5 9503 003 6440 Grooved ball bearing 6201-2RS → replaced by 9503 003 6420 TI 5/1994 2
7 4201 704 0504 Shaft 1
8 4201 706 9202 Washer 2
9 4221 706 8800 Rubber ring 1
10 4221 706 8801 Rubber ring 1
11 4223 700 2900 Adjusting lever 1
12 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 4
13 4205 706 2903 Flange 1
14 4223 710 9500 Adjusting screw
15 0000 997 1303 Compression spring
16 0000 958 1212 Washer 1
17 4223 036 8600 Woodruff key 1
18 4201 700 2504 NLA V-belt pulley 1
19 9291 021 0200 Washer 10.5 1
20 9211 260 1350 Hexagon nut M10x1 l/h thread 1
21 9450 721 2150 Circlip 20x1.2 1
22 4201 708 8402 Hexagon head screw M10x18 Fitment / change note → 1
23 4201 708 3004 Thrust washer Ø 103 mm 1
24 4201 708 3014 Thrust washer Ø 103 mm 1
25 4205 708 3000 Thrust washer Ø 118 mm 1
26 4205 708 3010 Thrust washer Ø 118 mm 1
27 0000 708 4200 Shaft sleeve option 1
28 4201 700 8116 Guard 1
29 4201 760 9500 Adjusting screw Fitment / change note → 1
30 4201 708 8401 Hexagon head screw M8x42 Fitment / change note → 2
31 4201 790 6005 Limit stop 1
32 4201 790 9302 Rubber buffer 1
33 9041 216 1230 Pan head screw M6x8 1
34 9062 319 1260 NLA Countersunk screw M6x12 1
35 0000 967 3577 Instruction label 1
36 0000 967 3578 Instruction label 1
37 0000 967 3522 Instruction label 1
Not numbered on the diagram — assemblies, kits and options
— 4223 007 1008 Support with guard Ø 300 mm / 12'' 1
— 4223 007 1016 Support with guard Ø 300 mm / 12'' 1
— 4223 007 1007 Support with guard Ø 300 mm / 12'' 1
— 4221 007 1009 Support with guard Ø 350 mm / 14'' 1
— 4221 007 1014 Support with guard Ø 350 mm / 14'' 1
— 4221 007 1008 Support with guard Ø 350 mm / 14'' 1
— 4221 007 1013 Support with guard Ø 350 mm / 14'' 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · TS 350 / TS 360

TS 350 / TS 360: polymer V-belt guard needs washers with old screws

Two A8.4 washers preserve compatibility with older 13 mm-head mounting screws.

  • Polymer V-belt guard replaces sheetmetal, saving approximately 0.2 kg (7 oz) according to the source. THREE mounting screws change from 13 mm to 19 mm across flats, and the eccentric adjuster changes from captive 13 mm nut operation to a slot or Torx recess turned with the combination-wrench blade.
  • New guard assembly 4201 700 8114 includes guard item 1 and TWO A8.4 washers 9291 021 0180 (item 2). These washers MUST be fitted on older machines retaining 13 mm-head screws, at the two locations illustrated. Do not omit them or infer that all three screws receive washers. The new bare guard is NOT separately available; original guard 4201 706 8100 and eccentric adjuster 4205 700 3200 are no longer factory-available.
  • Eccentric adjuster changes to 4205 708 3201. M8x40 13 mm-head screw 9007 319 1900 changes to M8x42 19 mm-head screw 4201 708 8401; original M8 screw remains available for other models.
  • Cutting-wheel M10x18 screw changes from 13 mm-head 9008 319 2350 to 19 mm-head 4201 708 8402. Original wheel screw remains factory-supplied only while stocks last; do not confuse this with the M8 mounting screws or cast-arm M10 screw.
  • Bearing-with-guard assembly numbers remain unchanged: diameter 300 mm 4201 007 1035, diameter 350 mm 4205 007 1035, USA-only 300 mm 4201 007 1040, USA-only 350 mm 4205 007 1040. Only modified assemblies are available, with polymer guard, associated 19 mm-head screws and new eccentric adjuster. Diameter and market rows remain distinct; no universal wheel-size conversion is authorized.
  • The prose says the guard change occurred some time ago; the summary says introduction in progress, without numeric cutoff. Keep both statements rather than assigning the muffler or tool-kit serial to this change.
  • Historical TI09/1994 guidance for the named TS 350 / TS 360 models only; no successor or TS 350 AVE applicability inferred from a shared IPL sheet. Across-flats dimensions describe wrench sizes, not thread diameters. Factory stock statements are historical, not current availability. MOQ columns are commercial order quantities. No physical interchange test was performed.

Source: TI 9/1994, p. 3 · TI 9/1994, p. 4 — TS 350 / TS 360: polymer V-belt guard needs washers with old screws.

Part numbers (13)
  • 4201 007 1035 — 300 mm bearing with guardunchanged assembly number · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 4205 007 1035 — 350 mm bearing with guardunchanged assembly number · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 4201 007 1040 — USA-only 300 mm bearing with guardunchanged assembly number · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 4205 007 1040 — USA-only 350 mm bearing with guardunchanged assembly number · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 4201 700 8114 — Guard with two washersnew assembly · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 4201 706 8100 — Bare guard, key 1original; no longer supplied · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 9291 021 0180 — A8.4 washers, two, key 2required with old mounting screws · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 4205 700 3200 — Eccentric adjusteroriginal; no longer supplied · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 4205 708 3201 — Eccentric adjuster, key 3new version · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 9007 319 1900 — M8x40, 13 mm-head screworiginal; retained for other models · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 4201 708 8401 — M8x42, 19 mm-head screw, key 4new version · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 9008 319 2350 — M10x18, 13 mm-head wheel screworiginal; while stocks last · TS 350 / TS 360: polymer V-belt guard needs washers with old screws
  • 4201 708 8402 — M10x18, 19 mm-head wheel screwnew version · TS 350 / TS 360: polymer V-belt guard needs washers with old screws

Service note · TS 350 / TS 360

TS 350 / TS 360: cast-arm screw changes length and wrench size

M10x35 with 17 mm head changes to M10x40 with 19 mm head.

  • The screw mounting the cast arm to the crankcase changes from 9008 319 2430 (M10x35, 17 mm across flats) to 4201 708 8403 (M10x40, 19 mm across flats). Original screw remains available for OTHER models. Introduction is in progress; no numeric cutoff or torque is given. This is distinct from the M10x18 cutting-wheel screw.
  • Historical TI09/1994 guidance for the named TS 350 / TS 360 models only; no successor or TS 350 AVE applicability inferred from a shared IPL sheet. Across-flats dimensions describe wrench sizes, not thread diameters. Factory stock statements are historical, not current availability. MOQ columns are commercial order quantities. No physical interchange test was performed.

Source: TI 9/1994, p. 3 · TI 9/1994, p. 4 — TS 350 / TS 360: cast-arm screw changes length and wrench size.

Part numbers (2)
  • 9008 319 2430 — M10x35 cast-arm screw, 17 mm headoriginal; retained for other models · TS 350 / TS 360: cast-arm screw changes length and wrench size
  • 4201 708 8403 — M10x40 cast-arm screw, 19 mm headnew version · TS 350 / TS 360: cast-arm screw changes length and wrench size

Service note · TS 350 / TS 360 / TS 510 / TS 760

TS 350 / 360 / 510 / 760: segment replaced by tensioning screw

4205 708 3201 is replaced by screw-with-segment assembly 4201 760 9500.

  • Page1 NOTE generally replaces segment4205 708 3201 with tensioning screw WITH SEGMENT4201 760 9500, expressly ALSO ON TS 350/360/510 in this TS 760 bulletin. Do not treat the new number as a bare segment or infer a complete 400 mm attachment from its availability.
  • This general replacement is distinct from the factory-only400 mm restriction. Sharing this tensioner does NOT permit TS 350, TS 360, TS 510 or an ordinary TS 760 to accept400 mm wheels. No adjustment torque or belt-tension method is supplied.
  • Exact named-model sheets retain9500; shared TS 350 AVE on the TS 360 sheet is not added to this bulletin’s explicit model list.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 31/1997, p. 1 · TI 31/1997, p. 2 — Page1 NOTE first paragraph and page2 item6.

Part numbers (2)
  • 4205 708 3201 — Original segmentGenerally replaced · Only the exact model/configuration and restrictions of 1997-31
  • 4201 760 9500 — Tensioning screw with segmentReplacement assembly; table item 6 · Only the exact model/configuration and restrictions of 1997-31

Wrong number or missing part for the TS 350? Report a correction →