← Cut-off machines · series 4201

Stihl 4201 · Section A · 1 of 24 · 36 parts

Crankcase

Fits TS 510, TS 760.

Parts diagrams →

Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
111010111213141516171819222021232425262727282933303132456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (36)

PosPart numberDescriptionQty
1 4205 020 2102 NLA Crankcase Fitment / change note → 1
2 4205 020 2103 NLA Crankcase Fitment / change note → 1
3 4205 020 2104 NLA Crankcase Fitment / change note → 1
4 9371 470 3120 Cylindrical pin 6x20 2
5 9022 341 1010 Spline screw IS-M5x18 10
6 9456 621 4910 Circlip 47x1.75 1
7 9503 003 0543 Grooved ball bearing 6204 1
8 9503 003 0443 Grooved ball bearing 6203 1
9 4201 708 8403 Hexagon head screw M10x40 Fitment / change note → 2
10 4205 647 9100 Grommet Fitment / change note → 2
11 4205 350 5800 Tank vent Fitment / change note → 1
12 1120 358 8105 Vent insert Fitment / change note → 1
13 not sold separately Hose 3.1x5.7x325 mm, R3 not available as a separate item 1
14 4205 141 8602 Hose 200 mm / 7 7/8'' Fitment / change note → 1
15 9629 003 2900 Oil seal 25x47x7 1
16 9640 003 1570 Oil seal 15x24x7 1
17 1111 084 6600 Insert 1
18 1111 029 0501 Gasket 1
19 1111 030 0402 Crankshaft 1
20 1120 036 8500 Woodruff key 2x3.7 1
21 9512 003 3440 Needle cage 13 x17x17.5 1
23 4205 350 0550 Filler cap Fitment / change note → 1
24 0000 992 6302 Sealing ring Fitment / change note → 1
25 4205 353 2300 Cap Fitment / change note → 1
26 9027 068 1480 Flat head screw M6x75 1
27 1111 790 9900 Annular buffer 2
28 1111 791 2700 Tube 1
29 1111 791 5400 Support 1
30 9022 341 1010 Spline screw IS-M5x18 2
31 9214 320 0900 Lock nut M6 1
32 1111 648 7700 Cover 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2803 Hose 3.1x5.7 mm x 1 m, R3 option 1
— 0712 923 8004 Hose 3.1x5.7 mm x 10 m, R3 option 1
— 1111 007 1050 Set of gaskets 1
— 1111 007 1052 Set of gaskets 1
— 1111 007 1051 NLA Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · TS 510 / TS 760

TS 510 / TS 760 cast-arm screws: larger head, different listed length

17-mm head M10x45 gives way to a 19-mm head; table explicitly lists M10x40.

  • Original cast-arm-to-crankcase mounting screw is M10x45, 17 mm across flats, 9007 319 2450. Prose describes replacement with a LARGER HEAD, 19 mm across flats; SUMMARY explicitly gives new screw 4201 708 8403 as M10x40, NOT M10x45. Preserve the table length and limited prose together; do not assume head size is the only dimensional change or silently label the new screw 45 mm long.
  • Original screw REMAINS AVAILABLE AS A SPARE FOR OLDER MACHINES. New screw row has an isolated printed1 in the remarks column without closing parenthesis; do not reinterpret it as an installed quantity. No mounting torque or universal screw-only retrofit approval supplied.
  • General changeover from HEXAGON SOCKET HEAD screws to TORX screws is announced for the near future. It is not a claim that these particular HEXAGON HEAD cast-arm screws become Torx. No complete Torx part roster or individual cutoff is supplied. Introduction IN PROGRESS, not the electronic-governor serial X24 073 218.
  • Exact-model crankcase sheet A lists new 8403 as M10x40 and older sheet B lists old 2450 as M10x45. Their later sheet cutoffs and quantities are not TI 33 introduction cutoffs or a correction of its remarks column. Shared TS 350 sheets are not additional applicability.
  • Historical TI guidance for the named models only. Shared catalog sheets do not extend applicability to other variants or successors. Factory supply statements are historical, not current stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 33/1995, p. 2 — TS 510 / TS 760 cast-arm screws: larger head, different listed length.

Part numbers (2)
  • 9007 319 2450 — Original M10x45, 17 mm across flatsolder-machine spare · TS 510 / TS 760; TS 510 / TS 760 cast-arm screws: larger head, different listed length
  • 4201 708 8403 — New M10x40, 19 mm across flatssummary dimensions retained · TS 510 / TS 760; TS 510 / TS 760 cast-arm screws: larger head, different listed length

Historical fitment · TS 510 / TS 760

TS 510 / TS 760: vented grey cap versus unvented orange cap

The cap must match the vent system; shared seals do not make both caps interchangeable.

  • From X 24 097 471, the compensating tank incorporated in the crankcase vents through a hose with threaded stud led to the CLEAN AIR SIDE of the air filter. It no longer vents through a hole in the compensating-tank filler cap. The crankcase and filter housing gain hose openings and new part numbers; this closed system avoids drawing dirty ambient air into the fuel system.
  • Section 3.1 REQUIRES grey filler cap 4205 007 1061, with vent hole and threaded stud, on machines with the ORIGINAL tank vent. It REQUIRES orange filler cap 4205 350 0550, WITHOUT a vent hole, on machines with the NEW tank vent. These are compensating-tank caps, not an unrestricted fuel-cap substitution. Colour identifies the source versions; verify the actual vent configuration rather than relying on colour alone.
  • Page 8 items 1–4: filler cap 4205 007 1061 → 4205 350 0550; sealing ring 0000 992 6302 and cap 4205 353 2300 are unchanged. Original 1/4-inch threaded stud 0000 951 5815 has a dash in the new column. The table groups items 2–4 under the filler cap, but the dash and section 3.1 prohibit inventing an old vent stud in the new unvented cap. Original filler cap and stud remain available for older machines under remark 1.
  • Later SCS 01-2012 sheet A lists the new cap and sheet B lists the original cap kit, seal, stud and cap. The shared seal and cover numbers do not override the explicit vent-system restriction or date every machine on those sheets to this changeover.
  • Historical TI26/1996 section 3 guidance for TS 510 and TS 760 only. Exact named-model sheets are consolidated under 4201; this is not general series interchange. Source availability statements describe 1996 supply, not current stock. No hardware operation was performed.

Source: TI 26/1996, p. 1 · TI 26/1996, p. 5 · TI 26/1996, p. 6 · TI 26/1996, p. 8 — TS 510 / TS 760: vented grey cap versus unvented orange cap.

Part numbers (5)
  • 4205 007 1061 — Grey filler cap with vent holeOriginal vent system required · TS 510 / TS 760; TS 510 / TS 760: vented grey cap versus unvented orange cap
  • 4205 350 0550 — Orange filler cap without vent holeNew vent system required · TS 510 / TS 760; TS 510 / TS 760: vented grey cap versus unvented orange cap
  • 0000 992 6302 — Sealing ringUnchanged · TS 510 / TS 760; TS 510 / TS 760: vented grey cap versus unvented orange cap
  • 0000 951 5815 — Threaded stud 1/4 inchOriginal vented cap; old spare · TS 510 / TS 760; TS 510 / TS 760: vented grey cap versus unvented orange cap
  • 4205 353 2300 — CapUnchanged · TS 510 / TS 760; TS 510 / TS 760: vented grey cap versus unvented orange cap

Historical fitment · TS 510 / TS 760

TS 510 / TS 760: replacement crankcase and vent-opening plug

Old crankcases stop at X 24 097 470; later replacements retain the old vent arrangement with a plug.

  • Section 3.2 permits replacement crankcases of the ORIGINAL type only UP TO X 24 097 470. They are supplied only until stocks are exhausted. Thereafter 4205 020 2102 is the general replacement for TS 510 and 4205 020 2103 for TS 760. The page 8 table gives originals 4205 020 2100 (TS 510) and 4205 020 2101 (TS 760). Do not interchange the two model-specific crankcases.
  • For machines with the ORIGINAL tank vent, the added hose opening is NOT needed and is factory-sealed with plug 1124 791 7303 (drawing 328TI004). General replacement does not mean converting every old machine to hose venting or fitting an unvented cap. Removing this plug is specified in section 3.2.1 only for machines with the NEW venting system.
  • When fitting a replacement crankcase the source requires checking ALL tank-vent parts and replacing them if necessary. It describes inclusion of a vent hose, insulating tube, two grommets, and a vent insert with threaded stud. Page 8 groups items 5–9 with the crankcase; separately numbered item 10 plug must not be silently folded into that numbered inclusion group.
  • Later sheet A retains 4205 020 2102 and 4205 020 2103, both marked no longer available in that edition, and also lists 4205 020 2104. This TI does not establish the latter part’s model assignment or supersession. Earlier sheet B instead lists 1111-family crankcases and a separate serial context; this note does not equate those with the printed 1996 originals.
  • Historical TI26/1996 section 3 guidance for TS 510 and TS 760 only. Exact named-model sheets are consolidated under 4201; this is not general series interchange. Source availability statements describe 1996 supply, not current stock. No hardware operation was performed.

Source: TI 26/1996, p. 1 · TI 26/1996, p. 5 · TI 26/1996, p. 6 · TI 26/1996, p. 8 — TS 510 / TS 760: replacement crankcase and vent-opening plug.

Part numbers (5)
  • 4205 020 2100 — Crankcase TS 510Original; through X 24 097 470 only · TS 510 / TS 760; TS 510 / TS 760: replacement crankcase and vent-opening plug
  • 4205 020 2101 — Crankcase TS 760Original; through X 24 097 470 only · TS 510 / TS 760; TS 510 / TS 760: replacement crankcase and vent-opening plug
  • 4205 020 2102 — Crankcase TS 510New; general replacement after old stock · TS 510 / TS 760; TS 510 / TS 760: replacement crankcase and vent-opening plug
  • 4205 020 2103 — Crankcase TS 760New; general replacement after old stock · TS 510 / TS 760; TS 510 / TS 760: replacement crankcase and vent-opening plug
  • 1124 791 7303 — Vent-opening plugRetained for original vent system · TS 510 / TS 760; TS 510 / TS 760: replacement crankcase and vent-opening plug

Historical fitment · TS 510 / TS 760

TS 510 / TS 760: hose-vent components and supplied quantities

The 325 mm vent hose and 200 mm insulating tube have different functions.

  • Page 8 items 5–10, introduced from X 24 097 471: vent hose 4205 141 8601, 325 mm, ONE; rubber grommet 4205 647 9100, TWO; insulating tube 4205 141 8602, 200 mm, ONE; vent insert 4205 350 5800 containing threaded stud 1120 358 8105; plug 1124 791 7303. All other parts are as previously. The new vent-insert stud is not old filler-cap stud 0000 951 5815.
  • Remark 3 applies to vent hose, grommet and insulating tube and literally says one of each is already fitted in the machine. Preserve that supply note alongside the table’s TWO grommets and section 3.2 crankcase contents; it does not reduce the installation to one grommet, prove all listed parts are loose spares, or increase the installed quantity by adding both statements together.
  • Later SCS 01-2012 sheet A describes position 13 as an unnumbered 3.1x5.7x325 mm R3 hose with a reference, and separately lists bulk hose. It does not retain 4205 141 8601 as the position’s order number. Keep the historical number searchable without silently assigning a later bulk-hose order number to the 1996 part.
  • Later sheet A calls 4205 350 5800 Tank vent and 1120 358 8105 Vent insert, whereas this TI calls them vent insert and threaded stud. Preserve the source-specific names and containment, not an invented additional component. Sheet A lists two grommets and sheet J one at the housing; those sheet quantities alone are not an installed-total reconciliation.
  • Historical TI26/1996 section 3 guidance for TS 510 and TS 760 only. Exact named-model sheets are consolidated under 4201; this is not general series interchange. Source availability statements describe 1996 supply, not current stock. No hardware operation was performed.

Source: TI 26/1996, p. 1 · TI 26/1996, p. 6 · TI 26/1996, p. 7 · TI 26/1996, p. 8 — TS 510 / TS 760: hose-vent components and supplied quantities.

Part numbers (6)
  • 4205 141 8601 — Vent hose 325 mmNew; quantity 1 · TS 510 / TS 760; TS 510 / TS 760: hose-vent components and supplied quantities
  • 4205 647 9100 — Rubber grommetNew; table quantity 2 · TS 510 / TS 760; TS 510 / TS 760: hose-vent components and supplied quantities
  • 4205 141 8602 — Insulating tube 200 mmNew; quantity 1 · TS 510 / TS 760; TS 510 / TS 760: hose-vent components and supplied quantities
  • 4205 350 5800 — Vent insert including threaded studNew assembly · TS 510 / TS 760; TS 510 / TS 760: hose-vent components and supplied quantities
  • 1120 358 8105 — Threaded studNew vent-insert component · TS 510 / TS 760; TS 510 / TS 760: hose-vent components and supplied quantities
  • 1124 791 7303 — PlugNew opening closure · TS 510 / TS 760; TS 510 / TS 760: hose-vent components and supplied quantities

Service note · TS 510 / TS 760

TS 510 / TS 760: hose assembly in a replacement crankcase

New-system installation removes the plug and locates the hose in the casing recesses.

  • Section 3.2.1 applies ONLY to machines with the NEW venting system receiving a replacement crankcase. First remove the plug in the clutch-side half. Draw the enclosed hose, with its vent insert fitted, through the opening; cut the end projecting into the carburetor chamber obliquely. Push on the grommet, wet it slightly with oil and press it into the casing, then push on the insulating tube.
  • Drawing 328TI005 labels hose (1), grommet (2), insulating tube (3) and a 240 mm (9.5 in.) projection. Position the hose as illustrated and press it into the casing recesses marked by arrows. These drawing numbers are NOT the page 8 table positions; 240 mm is a routing projection, not the 325 mm total replacement-hose length.
  • The source explicitly continues filter-housing connection under section 3.2.2 on pages 7–8. The installation is not complete at the end of page 6: retain the housing grommet, behind-strap routing, approximately 20 mm outlet projection and firmly seated separate compensator hose. This is historical source guidance, not a complete bench-readiness or live-engine procedure.
  • Historical TI26/1996 section 3 guidance for TS 510 and TS 760 only. Exact named-model sheets are consolidated under 4201; this is not general series interchange. Source availability statements describe 1996 supply, not current stock. No hardware operation was performed.

Source: TI 26/1996, p. 1 · TI 26/1996, p. 6 · TI 26/1996, p. 7 · TI 26/1996, p. 8 — TS 510 / TS 760: hose assembly in a replacement crankcase.

Part numbers (4)
  • 4205 141 8601 — Vent hoseReplacement-crankcase routing · TS 510 / TS 760; TS 510 / TS 760: hose assembly in a replacement crankcase
  • 4205 647 9100 — GrommetCasing and housing seals · TS 510 / TS 760; TS 510 / TS 760: hose assembly in a replacement crankcase
  • 4205 141 8602 — Insulating tubeHose protection · TS 510 / TS 760; TS 510 / TS 760: hose assembly in a replacement crankcase
  • 1124 791 7303 — PlugRemove only for new-system hose installation · TS 510 / TS 760; TS 510 / TS 760: hose assembly in a replacement crankcase

Service note · TS 510 / TS 760

TS 510 / TS 760: defective vent hose and final connections

Retain the 240 / 40 / 20 mm routing stages and the distinct compensator connection.

  • Section 3.2.2 applies ONLY to the NEW tank-vent system. Remove air filter, filter housing and carburetor; pry the cap off the compensating-tank twist lock and unscrew the lock. Separate the defective hose in the carburetor chamber and withdraw it through the compensating-tank opening using needle-nose pliers; remove the housing grommet.
  • Drawing 328TI006: feed an approximately 50 cm (19.5 in.) trimmer line, maximum diameter 0.095 in., or flexible wire such as throttle cable, from the carburetor chamber through the compensating tank as an assembly aid. Cut one end of vent hose 4205 141 8601 obliquely; use the aid to push the other end through the tank until it protrudes. Remove the aid and push the vent insert into that protruding end. The line is an assembly aid, not a permanent vent component.
  • Push on grommet (2), wet slightly with oil and press in; withdraw the hose until it projects approximately 240 mm (9.5 in.) into the carburetor chamber. Push on insulating tube 4205 141 8602 (3), leaving approximately 40 mm (1.5 in.) of hose beyond its end (328TI007). These projections are not cut lengths; the table specifies a 325 mm hose and a 200 mm tube.
  • Refit carburetor and fuel hose and connect impulse hose. Press grommet (4) into the filter housing; lead the vent hose with insulating tube along the illustrated route and through the grommet (328TI008). Connect short-circuit wire (5) to the stop switch. Do not confuse the impulse hose, vent hose or short-circuit wire.
  • Page 8 / 328TI009 finishes the procedure: fit the filter housing with the vent hose BEHIND THE STRAP, then pull it upward to protrude approximately 20 mm (3/4 in.). IMPORTANT: the separate COMPENSATOR hose (6) protruding DOWNWARDS from the filter housing must be firmly seated on the carburetor connection piece. The upward vent outlet is not that compensator connection. Illustration numbers 1–6 and table positions 1–10 are separate numbering systems.
  • All three metric/inch pairs are the source’s approximate routing dimensions, not exact unit conversions or three successive cuts. Read the original diagrams before physical work; no live adjustment, leak test or completed repair is claimed.
  • Historical TI26/1996 section 3 guidance for TS 510 and TS 760 only. Exact named-model sheets are consolidated under 4201; this is not general series interchange. Source availability statements describe 1996 supply, not current stock. No hardware operation was performed.

Source: TI 26/1996, p. 1 · TI 26/1996, p. 7 · TI 26/1996, p. 8 — TS 510 / TS 760: defective vent hose and final connections.

Part numbers (4)
  • 4205 141 8601 — Vent hoseDefective-hose replacement · TS 510 / TS 760; TS 510 / TS 760: defective vent hose and final connections
  • 4205 141 8602 — Insulating tube40 mm vent-hose projection · TS 510 / TS 760; TS 510 / TS 760: defective vent hose and final connections
  • 4205 647 9100 — GrommetCasing and filter-housing routing · TS 510 / TS 760; TS 510 / TS 760: defective vent hose and final connections
  • 4205 350 5800 — Vent insertInserted after withdrawing assembly aid · TS 510 / TS 760; TS 510 / TS 760: defective vent hose and final connections

Service note · TS 760

TS 760 400 mm factory version: reinforced drive and guard

Ten listed components describe the factory machine, not a retrofit recipe.

  • ONLY THE PARTICULAR FACTORY-PRODUCED 400 mm TS 760 is covered. The required parts MUST NOT be mounted on other STIHL cut-off machines; this roster is not a conversion recipe. Modified crankcase, reinforced aluminium cast arm and bearings, longer V-belt, 106 mm (4.2 in.) pulley, V-belt guard, tensioning screw with segment and aluminium shroud are described on page1.
  • Drawing 336TI001 KN identifies all ten summary items. Two halves marked1 belong to the single crankcase entry, not two separately numbered cases. V-belt is 10 x 950 mm; pulley diameter is 106 mm. No separate aluminium-shroud part number, torque, wheel speed, belt-tension procedure or serial cutoff is supplied.
  • The new version accepts a historical range of 400 mm composite and diamond wheels for concrete, asphalt, rock and steel. This is not permission for every wheel to cut every material. Maximum depth is 143.5 mm (5.65 in.), DEPENDING ON WHEEL VERSION. Weight WITHOUT CUTTING WHEEL is 15.3 kg (33.7 lb); do not call it operating weight.
  • The exact named TS 760 catalog sheets are consolidated under4201, not a general type4201/4205 equivalence. Later sheet O calls3903 a Support and1260 a Spline screw IS-M6x12, and lists400 mm guard4224 700 8105 rather than the TI’s4205 700 8105. Preserve source-specific names and numbers; no silent substitution or independently proven supersession. The shared TS 510 heading grants no 400 mm compatibility. Catalog NLA flags are later catalog context, not 1997 supply remarks.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 31/1997, p. 1 · TI 31/1997, p. 2 — Page1 new version/specifications and page2 complete ten-item drawing/table.

Part numbers (10)
  • 4205 020 2104 — Crankcase; item 1Modified factory version · Only the exact model/configuration and restrictions of 1997-31
  • 4205 700 1210 — Cast arm; item 2Reinforced aluminium · Only the exact model/configuration and restrictions of 1997-31
  • 9490 000 7895 — V-belt 10 x 950 mm; item 3Longer belt · Only the exact model/configuration and restrictions of 1997-31
  • 4205 704 1004 — V-belt pulley; item 4106 mm (4.2 in.) · Only the exact model/configuration and restrictions of 1997-31
  • 4205 706 8105 — V-belt guard; item 5Factory 400 mm configuration · Only the exact model/configuration and restrictions of 1997-31
  • 4201 760 9500 — Tensioning screw with segment; item 6New assembly · Only the exact model/configuration and restrictions of 1997-31
  • 9022 341 1260 — Socket-head screw M6x12; item 7Source description retained · Only the exact model/configuration and restrictions of 1997-31
  • 4205 791 3903 — Bearing; item 8Reinforced; later catalog calls it support · Only the exact model/configuration and restrictions of 1997-31
  • 4205 700 8105 — Guard, 400 mm (16 in.); item 9Source number, not later guard number · Only the exact model/configuration and restrictions of 1997-31
  • 4205 792 9400 — Stop (USA); item 10USA restriction · Only the exact model/configuration and restrictions of 1997-31

Historical fitment · TS 510 / TS 760

TS 510 / TS 760: two clips secure the impulse hose

One clip secures each hose end at the crankcase and carburetor; introduction was in progress, without a serial cutoff.

  • TI32/1999 names TS 510 and TS 760, series 4205. Exact-model navigation is under catalog family 4201 in the 2012 IPL; this does not change the source type or extend applicability to TS 350/360. Historical availability is not current stock, and source review is not verified physical interchange.
  • Section 2 adds hose clips to secure the impulse hose to the stubs on the crankcase and carburetor. The summary lists Hose clip (2), order number 4205 122 2500: two clips for the two connections, not a replacement hose or a single clip for both ends.
  • Drawing 328TI028 KN shows the crankcase-side connection and a magnified clip, local callout 1, with a directional arrow. It locates the clip but supplies no installation tool, force, dimension or torque. Do not turn the local callout into a later IPL position or infer an unsupported fitting operation from the arrow.
  • The hose-clip modification is described as in progress. The trigger/control-valve serial thresholds in section 1 do not date this separate change. No hose-clip serial boundary or specific retrofit procedure is stated.
  • The exact-model crankcase assembly provides navigation to the impulse-hose context; its original parts rows and hotspots are unchanged. The 1999 hose-clip statement is not blanket fitment for other machines or evidence of current stock. No hardware was connected or operated.

Source: TI 32/1999, p. 2 — Page 2 section 2: full impulse hose text, illustration 328TI028 KN, summary and introduction status.

Part numbers (1)
  • 4205 122 2500 — Hose clipTwo clips specified · TS 510 / TS 760 impulse hose at crankcase and carburetor stubs

Wrong number or missing part for the TS 510, TS 760? Report a correction →