Stihl 4203 · Section D · 4 of 10 · 58 parts
Carburetor HD-4B, HD-13B
Fits BR 320, BR 320 L, BR 400.
Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.
Parts (58)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 121 5100 | Inlet needle | 1 |
| 2 | 4116 122 3000 | Spring | 1 |
| 3 | 1113 121 9200 | Spindle | 1 |
| 4 | 4116 121 5000 | Inlet control lever | 1 |
| 5 | 1114 122 7400 | Round head screw | 1 |
| 6 | 1120 121 5405 | Valve jet | 1 |
| 7 | 4117 122 9402 | Plug | 1 |
| 8 | 4116 129 0901 | Gasket | 1 |
| 9 | 4116 121 4700 | Metering diaphragm | 1 |
| 10 | 4116 121 0800 | End cover | 1 |
| 11 | 1106 122 7400 | Round head screw | 4 |
| 12 | 1114 121 7800 | Strainer | 1 |
| 13 | 4116 121 4800 | Pump diaphragm | 1 |
| 14 | 4116 129 0902 | Gasket | 1 |
| 15 | 4203 121 0800 | End cover | 1 |
| 16 | 1114 122 7100 | Screw | 1 |
| 18 | 4117 122 6200 | Idle speed adjustment screw | 1 |
| 19 | 4116 120 7100 | Throttle shaft with lever | 1 |
| 20 | 4116 122 3200 | Torsion spring | 1 |
| 21 | 4116 121 3300 | Throttle shutter | 1 |
| 22 | 1115 122 7400 | Round head screw | 2 |
| 23 | 4116 122 5000 | Spacer sleeve | 1 |
| 24 | 4203 123 7300 | Lever | 1 |
| 25 | 1110 122 7400 | Round head screw | 1 |
| 26 | 4215 121 8600 | Washer | 1 |
| 27 | 4215 121 8900 | Pin | 1 |
| 28 | 1117 122 9000 | E-clip | 1 |
| 29 | 1116 122 3000 | Spring | 1 |
| 30 | 1116 122 4200 | Ball | 1 |
| 31 | 4203 121 3001 | Choke shaft | 1 |
| 32 | 4116 121 2900 | Choke shutter | 1 |
| 33 | 4117 122 3006 | Spring | 1 |
| 34 | 4116 122 3001 | Spring | 2 |
| 35 | 4203 122 6701 | High speed adjustment screw | 1 |
| 36 | 4203 122 6801 | Low speed adjustment screw | 1 |
| 38 | 4203 122 6703 | High speed adjustment screw Fitment / change note → | 1 |
| 39 | 4203 122 6804 | Low speed adjustment screw Fitment / change note → | 1 |
| 40 | 4203 121 2700 | Cap Fitment / change note → | 2 |
| 41 | 4203 121 5400 | Valve jet 0.52 | 1 |
| 42 | 5910 890 4500 | Puller Fitment / change note → option | 1 |
| 50 | 4130 122 3600 | Sealing ring | 1 |
| 51 | 4130 121 8601 | Washer | 1 |
| 52 | 1115 122 3002 | Spring | 2 |
| 53 | 4130 121 8602 | Washer | 2 |
| 54 | 4130 122 6701 | High speed adjustment screw | 1 |
| 55 | 4130 121 2701 | Cap | 1 |
| 56 | 4124 122 3600 | Sealing ring | 1 |
| 57 | 1111 121 8605 | Washer | 1 |
| 58 | 4130 122 6801 | Low speed adjustment screw | 1 |
| 59 | 4130 121 2700 | Cap | 1 |
| 60 | 4130 122 3601 | Sealing ring | 1 |
| 61 | 4203 121 3000 | Choke shaft | 1 |
| 62 | 4116 122 6700 | High speed adjustment screw | 1 |
| 63 | 4116 122 6800 | Low speed adjustment screw | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4203 120 0601 | Carburetor HD-4B | 1 |
| — | 4203 120 0603 | Carburetor HD-13B Fitment / change note → | 1 |
| — | 4116 007 1061 | Set of carburetor parts | 1 |
| — | 4203 120 0602 | Carburetor HD-7 no longer available from factory | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · BR 320 / BR 340 / BR 400 / BR 420 / SR 320 / SR 340 / SR 400 / SR 420 / FS 550
BR/SR blowers and FS 550: revised limiter cap keeps the same number
Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
Later reviewed guidance: BR/SR blowers and FS 550: square-bit driver for fitted limiter caps
- Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
- The new cap has no upper detent, adds an alignment mark and moves the lug from perpendicular to the screw slot into line with it.
- These models appear on the bulletin cover but NOT in the marked-segment subset on pages 2–4. Do not infer marked-segment alignment from cover inclusion; the slot, groove and visible-lug checks remain distinct from the marks-only instruction.
- The marked-segment drawing and its dimensions must not be assigned to these models solely from the shared limiter-cap number.
- H and L removal have separate alignment instructions. Puller 5910 890 4500 has a left-hand engagement thread; this note is not a complete carburetor removal or calibration procedure.
- Removed limiter caps must not be reused because removal damages them. Replace caps after screw replacement or carburetor cleaning; no permanent cap-removal modification is implied.
- Applies only to the named models with limiter cap 4203 121 2700. A shared catalog sheet is not approval for its other models or C/L variants. The sheet may contain uncapped versions; verify the actual carburetor configuration.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 21/2005, p. 1 · TI 21/2005, p. 2 · TI 21/2005, p. 3 · TI 21/2005, p. 4 — Sections 1–5: named-model cap revision; cover list distinguished from marked-segment subset.
Part numbers (2)
- 4203 121 2700 — Limiter capUnchanged number, revised geometry · Named models using 4203 121 2700; single-use after removal
- 5910 890 4500 — Limiter-cap pullerService tool · Left-hand engagement; separate H/L alignment
Conditional replacement · BR 320 / BR 340 / BR 400 / BR 420 / SR 320 / SR 340 / SR 400 / SR 420 / FS 550
BR/SR blowers and FS 550: square-bit driver for fitted limiter caps
Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
- Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
- Conditional on limiter cap 4203 121 2700 actually being fitted, not every carburetor or every model/variant on the shared catalog sheet. Model association comes from TI 21/2005 and the catalog cap row; TI 50/2006 specifies the tool by cap configuration.
- The without-cap basic-setting illustration starts with adjusting screws closed to their seats. It does not supply a turn count or extend the illustrated H/L arrangement to every carburetor on this sheet.
- The source distinguishes initial engagement at the first detent from final fully-home seating after the series-specific basic setting. Do not treat the first detent as the completed installation.
- Required idle/high-speed settings depend on the exact series; this bulletin supplies no universal screw-turn or RPM setting. Later series-specific service guidance still governs.
- Caps removed to service an adjusting screw or clean the carburetor must not be reused. TI 21/2005 supplies the removal dependency; this is not authorization for permanent limiter removal.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 50/2006, p. 3 · TI 50/2006, p. 4 · TI 50/2006, p. 5 — Sections 3–3.4 and summary: capped-carburetor service tool and seating stages.
Part numbers (2)
- 5910 890 2304 — Square-bit carburetor screwdriverService tool · Carburetors using 4203 121 2700 fitted caps
- 4203 121 2700 — Limiter capExact tool configuration · New caps; final seating after series-specific basic setting
Service note · BR 320 / BR 400
BR 320 / BR 400: HD13 carburetor and exact included components
HD13 has its own H/L screws; shared caps and rings do not make the screws interchangeable.
- The model table assigns HD13 to BR 320 and BR 400, NOT BR 320 L. Page 3 item 1 is carburetor 4203 120 0603 and explicitly includes items 4, 5, 8 and 9: high-speed screw 4203 122 6703, low-speed screw 4203 122 6804, two limiter caps 4203 121 2700 and two sealing rings 4203 122 3600.
- Introduction is IN PROGRESS. No serial cutoff, old assembly number, universal retrofit approval or present stock status is supplied. The page 1 drawing numbers 1–4 identify component functions; they are NOT the page 3 spare-parts item numbers.
- Historical TI11/1997 evidence for the named carburetor versions only, not every carburetor on these models. Later IPL sheet labels HD-13B and WT-492A are discovery context, not proof of unchanged calibration. The shared BR sheets also name other variants; this note does not extend its model list to them. No hardware operation was performed.
Source: TI 11/1997, p. 1 · TI 11/1997, p. 3 — BR 320 / BR 400: HD13 carburetor and exact included components.
Part numbers (5)
- 4203 120 0603 — Carburetor HD13, item 1New assembly · BR 320/BR 400; BR 320 / BR 400: HD13 carburetor and exact included components
- 4203 122 6703 — High-speed screw, item 4HD13 component · BR 320/BR 400; BR 320 / BR 400: HD13 carburetor and exact included components
- 4203 122 6804 — Low-speed screw, item 5HD13 component · BR 320/BR 400; BR 320 / BR 400: HD13 carburetor and exact included components
- 4203 121 2700 — Limiter cap; two per carburetorShared new component · BR 320/BR 400; BR 320 / BR 400: HD13 carburetor and exact included components
- 4203 122 3600 — Sealing ring; two per carburetorShared new component · BR 320/BR 400; BR 320 / BR 400: HD13 carburetor and exact included components
Service note · BR 320 / BR 320 L / BR 400 / FS 36 / FS 40 / FS 44 / FC 44
BR / FS / FC: identical limiter caps, sealing rings and left-hand puller
90-degree range, single-use caps and flush installation remain explicit.
- The new high- and low-speed limiter caps are identical. A separate sealing ring on each adjusting screw seals against the carburetor body and helps prevent air leakage through its threads. Screw knurling locks the pressed-in caps, which sit flush with the body. No ring dimensions or torque are specified.
- Each mounting hole has a quadrant stop; each cap has a molded tang. Together they limit adjustment to 90 degrees, at most 1/4 turn. Page 2 presents this as allowing a leaner mixture at higher altitude without enriching beyond the stated CARB/EPA limits. This is a dated design/regulatory statement, not current compliance certification.
- For correction of the basic setting in the service shop, the source specifies puller 5910 890 4500 for BOTH L and H caps. It has a LEFT-HAND thread and screws into a cap COUNTERCLOCKWISE. The molded tang meets the stop; the puller presses against the screw head and eases the cap out. Do not reinterpret the rotation as a right-hand thread.
- Caps removed once MUST NOT be reused. Section 1.4.6 requires NEW caps pushed into the screw holes until flush with the carburetor body. The subsequent running-behavior check is mandatory in the flow chart. Page 3 item 10 is the puller; it is NOT included in carburetor item ranges 4/5/8/9 or 6–9.
- Historical TI11/1997 evidence for the named carburetor versions only, not every carburetor on these models. Later IPL sheet labels HD-13B and WT-492A are discovery context, not proof of unchanged calibration. The shared BR sheets also name other variants; this note does not extend its model list to them. No hardware operation was performed.
Source: TI 11/1997, p. 1 · TI 11/1997, p. 2 · TI 11/1997, p. 3 · TI 11/1997, p. 7 — BR / FS / FC: identical limiter caps, sealing rings and left-hand puller.
Part numbers (3)
- 4203 121 2700 — Limiter cap; two per carburetorShared new component · BR 320/BR 320 L/BR 400/FS 36/FS 40/FS 44/FC 44; BR / FS / FC: identical limiter caps, sealing rings and left-hand puller
- 4203 122 3600 — Sealing ring; two per carburetorShared new component · BR 320/BR 320 L/BR 400/FS 36/FS 40/FS 44/FC 44; BR / FS / FC: identical limiter caps, sealing rings and left-hand puller
- 5910 890 4500 — Left-hand-thread limiter-cap puller, item 10Service tool; not included in carburetor · BR 320/BR 320 L/BR 400/FS 36/FS 40/FS 44/FC 44; BR / FS / FC: identical limiter caps, sealing rings and left-hand puller
Service note · BR 320 / BR 320 L / BR 400 / FS 36 / FS 40 / FS 44 / FC 44
BR / FS / FC: preparation and both running-behavior checks
The flow chart returns BOTH failed checks to idle adjustment, not directly to completion.
- Page 4 sequence: preparations (1.4.1), basic setting (1.4.2), idle adjustment (1.4.3), full-load adjustment (1.4.4), running-behavior check (1.4.5), NEW limiter-cap installation (1.4.6), then a SECOND running-behavior check. A NO at EITHER check returns to IDLE adjustment, then full-load adjustment; only the final YES ends the procedure. The return arrows are visible in the original, not recoverable from flattened OCR alone.
- Engine speeds MUST be checked with a tachometer. Inspect and, if needed, clean the air filter; inspect the spark-arresting screen and clean or replace it as needed. On blowers mount the blower tubes AND nozzle. On brushcutters mount a STIHL Autocut or Polymatic head and initially set the lines to the limiting blade on the deflector. The later full-load line-length instruction is retained separately.
- SOURCE SCOPE ANOMALY: preparations also say to clean and oil hedge-trimmer blades, but NO hedge trimmer is named on the cover or in either settings table. This sentence is preserved without inventing HS-model applicability or settings. No specific edger preparation is printed here; do not substitute a mowing head on FC 44.
- The running-behavior check opens the throttle several times to verify smooth acceleration; the engine must also idle smoothly. If a check after cap installation requires removal, the no-reuse rule still applies. These are historical service instructions, not a report that a machine was adjusted.
- Historical TI11/1997 evidence for the named carburetor versions only, not every carburetor on these models. Later IPL sheet labels HD-13B and WT-492A are discovery context, not proof of unchanged calibration. The shared BR sheets also name other variants; this note does not extend its model list to them. No hardware operation was performed.
Source: TI 11/1997, p. 4 · TI 11/1997, p. 5 · TI 11/1997, p. 7 — BR / FS / FC: preparation and both running-behavior checks.
No additional parts-table entry added.
Service note · BR 320 / BR 320 L / BR 400
BR 320 / BR 320 L / BR 400: distinct basic settings, common blower procedure
BR 320 L L/H = 1.5/4 turns; BR 320 and BR 400 = 2/2.5 turns.
- For WT489 on BR 320 L: basic L = 1.5 turns and H = 4 turns open. For HD13 on BR 320 and BR 400: basic L = 2 turns and H = 2.5 turns open. Do not collapse the BR 320 L and BR 320 rows or transfer these settings to other carburetor versions.
- Basic opening is measured from screws LIGHTLY seated. After the basic setting the source starts the engine. Idle procedure: find maximum idle speed with L, then turn L counterclockwise until speed drops ABOUT 300 rpm; use the SEPARATE idle-speed screw LA to set 3,100 rpm. The 300 rpm drop is not itself the final idle target. Tachometer, filter/screen checks, equipment preparation and BOTH running-behavior checks apply.
- With blower tubes AND nozzle mounted, the full-load procedure runs at full throttle, slowly turns H clockwise to maximum engine speed, then turns H counterclockwise until speed drops ABOUT 100 rpm. NO absolute full-load rpm is specified for these blowers; the FS range and FC targets must not be substituted. Repeat running-behavior checks around installation of new limiter caps.
- Historical TI11/1997 evidence for the named carburetor versions only, not every carburetor on these models. Later IPL sheet labels HD-13B and WT-492A are discovery context, not proof of unchanged calibration. The shared BR sheets also name other variants; this note does not extend its model list to them. No hardware operation was performed.
Source: TI 11/1997, p. 1 · TI 11/1997, p. 4 · TI 11/1997, p. 5 · TI 11/1997, p. 6 · TI 11/1997, p. 7 — BR 320 / BR 320 L / BR 400: distinct basic settings, common blower procedure.
No additional parts-table entry added.
Service note · BR 320 / BR 320 L / BR 400 / FS 36 / FS 40 / FS 44 / FC 44
BR / FS / FC: 50:1 approval statement and bounded reference gaps
Exact user-instruction and California warranty references are unavailable in the verified local pools.
- TI11/1997 states emissions approval was obtained with a 50:1 fuel-oil mix and that no emissions measurements are available for other mix ratios. It does not establish approval for other ratios, a present-day legal status, a lubricant grade or a fuel specification beyond this ratio.
- Section 2 says the user setting instructions are exactly those in the owner’s manual chapter Adjusting the Carburetor, but does not reproduce that chapter or identify its edition. Sections 3 and 4 refer to TI41/1994 and TI47/1994 for fuel context and the California Emission Control Warranty Statement. Neither TI nor the exact owner-manual chapters/editions was found in the verified local pools: 690 retained TIs, 766 resource PDFs, 41 owner-collected service PDFs and document metadata/model associations. These are THREE bounded source dependencies, not proof that the documents do not exist elsewhere.
- Exact catalog products 49 (BR 320/320 L/400), 68 (FC 44) and 101 (FS 36/40/44) have no linked manual. A same-name later FS 40 group, product 447, links SERIES 4144 workshop documents, not the SERIES 4130 owner chapter named here. The generic Manuals category contains special-tools and chain/bar manuals only. No later FS 40 procedure or unverified warranty text is substituted.
- The last-TI list (BR 320/400:14/1996; FS 36/40/44:19/1996; FC 44:07/1996) is bibliographic context, not an additional fitment or calibration claim. The original repeats section number 1.3 for Adjustment and New spare parts; citations use page and title to avoid ambiguity.
- Historical TI11/1997 evidence for the named carburetor versions only, not every carburetor on these models. Later IPL sheet labels HD-13B and WT-492A are discovery context, not proof of unchanged calibration. The shared BR sheets also name other variants; this note does not extend its model list to them. No hardware operation was performed.
Source: TI 11/1997, p. 7 — BR / FS / FC: 50:1 approval statement and bounded reference gaps.
No additional parts-table entry added.
Wrong number or missing part for the BR 320, BR 320 L, BR 400? Report a correction →