← Blowers & other equipment · series 4203

Stihl 4203 · Section C · 3 of 12 · 30 parts

Air filter, Ignition system

Fits SR 320, SR 400.

Parts diagrams →

Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1110111213141516171819220212223242526273456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (30)

PosPart numberDescriptionQty
1 4203 129 0901 Gasket 2
2 4203 122 1600 Heat shield 1
3 9022 341 0980 Spline screw IS-M5x16 2
4 4203 120 2200 Flange 1
5 9022 341 1050 Spline screw IS-M5x25 2
6 4203 129 0900 Gasket Fitment / change note → 1
7 4203 120 0601 Carburetor HD-4B Fitment / change note → 1
8 4203 120 0603 Carburetor HD-13B 1
9 4203 182 9501 Choke knob 1
10 4119 182 9500 Choke knob 1
11 4203 182 9505 Choke knob 1
12 4203 140 2803 Filter housing Fitment / change note → 1
13 9443 825 7130 Hollow rivet 7.5x1x6.8 3
14 9022 341 1220 Spline screw IS-M5x48 2
15 4203 141 0305 Air filter 1
16 4203 140 1002 Filter cover Fitment / change note → 1
17 4227 700 2300 Screw plug 2
18 4203 400 1200 Flywheel Fitment / change note → 1
19 9210 261 1140 Hexagon nut M8x1 1
20 4203 400 1301 Ignition module Fitment / change note → → replaced by 4203 400 1302 TI 19/2001 1
21 not sold separately Ignition lead 270 mm not available as a separate item 1
22 0751 030 8415 Spade terminal 6.3 1
23 9022 341 1019 Spline screw IS-M5x20 2
24 0000 989 0602 Grommet 1
25 9291 021 0120 Washer 5.3 1
26 4203 141 0300 Air filter Fitment / change note → option 1
27 4203 141 0310 Prefilter Fitment / change note → option 1
Not numbered on the diagram — assemblies, kits and options
— 0000 405 0600 NLA Ignition lead 1 m option 1
— 0000 930 2251 Ignition lead 10 m option 1
— 4203 007 1025 Air filter kit option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · BR 320 / BR 400 / SR 320 / SR 400

BR 320 / BR 400 / SR 320 / SR 400: series 4203 replacement ignition assignment

4203 400 1301 with flywheel 4203 400 1200; 270 mm ignition lead.

  • Printed series 4203. Use 4203 400 1301 with flywheel 4203 400 1200.
  • Printed ignition-lead length: 270 mm (10 5/8 in). Preserve both printed units.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.

Part numbers (2)
  • 4203 400 1301 — Replacement ignition moduleAssigned component · BR 320 / BR 400 / SR 320 / SR 400, printed series 4203, listed combination only
  • 4203 400 1200 — Assigned flywheelRequired pairing · BR 320 / BR 400 / SR 320 / SR 400, printed series 4203

Service note · BR 320 / BR 400 / SR 320 / SR 400

BR / SR 320 / 400: renew gasket whenever carburetor is removed

The two gasket numbers are alternatives in the service sentence, not a stacking instruction.

  • Gasket 4203 129 0900 OR 4114 129 0501 should be replaced EVERY TIME the carburetor is removed. Both are listed in hose kit 4203 007 1017, but this does not require fitting both together. The page gives no gasket-selection rule for individual carburetor variants.
  • This separate carburetor-removal instruction has no serial qualification. Do not assign the earlier X 25 117 539 elbow-deletion cutoff to gasket renewal. Shared BR320L drawing does not extend this TI to BR320L.
  • Historical TI 21/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply and warranty statements are historical, not current availability or entitlement. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 21/1994, p. 1 — BR / SR 320 / 400: renew gasket whenever carburetor is removed.

Part numbers (3)
  • 4203 129 0900 — Carburetor gasketrenew on removal · BR / SR 320 / 400: renew gasket whenever carburetor is removed
  • 4114 129 0501 — Carburetor gasketsource alternative · BR / SR 320 / 400: renew gasket whenever carburetor is removed
  • 4203 007 1017 — Fuel hose kitincludes both listed gaskets · BR / SR 320 / 400: renew gasket whenever carburetor is removed

Historical fitment · BR 320 / BR 400 / SR 320 / SR 400

BR / SR 320 / 400 bulletin: HD-4 A requires new adjustment screws

4203 120 0601 keeps its number; only new high/low speed screws may be used in the new carburetor.

  • The HD-4 becomes HD-4 A with new high and low speed screws to optimize fine tuning; carburetor number 4203 120 0601 stays unchanged. The carburetor includes both screws. Only the MODIFIED CARBURETOR is factory-supplied.
  • High speed screw 4116 122 6700 → 4203 122 6701; low speed screw 4116 122 6800 → 4203 122 6801. The table retains original screws FOR OTHER MODELS. The service note explicitly permits ONLY NEW VERSIONS OF BOTH SCREWS IN NEW CARBURETORS. It does not establish reverse compatibility of new screws in every old carburetor or give mixture settings.
  • The bulletin header names BR/SR 320 and 400 but does not allocate each carburetor to individual models or variants. Binding to shared exact-model air-filter sheets is context, not proof that every named model used this carburetor. Current catalog labels 0601 as HD-4B and places WT-230A 0605 on a BR 320 L carburetor sheet, despite the TI header omitting L. These model/designation differences remain unresolved; no BR 320 L scope or HD-4B screw applicability is inferred.
  • Historical TI 14/1996 evidence, not current stock or a verified physical interchange claim. Introduction is in progress; no numeric serial boundary is given. Shared IPL sheets do not extend this note to BR 320 L or later models. No hardware operation was performed.

Source: TI 14/1996, p. 3 · TI 14/1996, p. 4 — BR / SR 320 / 400 bulletin: HD-4 A requires new adjustment screws.

Part numbers (5)
  • 4203 120 0601 — Carburetor HD-4 → HD-4 A, same numberTI14/1996 listed configuration · Only the note’s stated models and configuration
  • 4116 122 6700 — Original high speed screw, retained for other modelsTI14/1996 listed configuration · Only the note’s stated models and configuration
  • 4203 122 6701 — New high speed screwTI14/1996 listed configuration · Only the note’s stated models and configuration
  • 4116 122 6800 — Original low speed screw, retained for other modelsTI14/1996 listed configuration · Only the note’s stated models and configuration
  • 4203 122 6801 — New low speed screwTI14/1996 listed configuration · Only the note’s stated models and configuration

Historical fitment · BR 320 / BR 400 / SR 320 / SR 400

BR / SR 320 / 400 bulletin: WT 230 A requires new adjustment screws

4203 120 0605 keeps its number; only new high/low speed screws may be used in the new carburetor.

  • The WT 230 becomes WT 230 A with new high and low speed screws to optimize fine tuning; carburetor number 4203 120 0605 stays unchanged. The carburetor includes both screws. Only the MODIFIED CARBURETOR is factory-supplied.
  • High speed screw 1120 122 6705 → 4130 122 6700; low speed screw 4119 122 6801 → 4203 122 6802. The table retains original screws FOR OTHER MODELS. The service note explicitly permits ONLY NEW VERSIONS OF BOTH SCREWS IN NEW CARBURETORS. It does not establish reverse compatibility of new screws in every old carburetor or give mixture settings.
  • The bulletin header names BR/SR 320 and 400 but does not allocate each carburetor to individual models or variants. Binding to shared exact-model air-filter sheets is context, not proof that every named model used this carburetor. Current catalog labels 0601 as HD-4B and places WT-230A 0605 on a BR 320 L carburetor sheet, despite the TI header omitting L. These model/designation differences remain unresolved; no BR 320 L scope or HD-4B screw applicability is inferred.
  • Historical TI 14/1996 evidence, not current stock or a verified physical interchange claim. Introduction is in progress; no numeric serial boundary is given. Shared IPL sheets do not extend this note to BR 320 L or later models. No hardware operation was performed.

Source: TI 14/1996, p. 3 · TI 14/1996, p. 4 — BR / SR 320 / 400 bulletin: WT 230 A requires new adjustment screws.

Part numbers (5)
  • 4203 120 0605 — Carburetor WT 230 → WT 230 A, same numberTI14/1996 listed configuration · Only the note’s stated models and configuration
  • 1120 122 6705 — Original high speed screw, retained for other modelsTI14/1996 listed configuration · Only the note’s stated models and configuration
  • 4130 122 6700 — New high speed screwTI14/1996 listed configuration · Only the note’s stated models and configuration
  • 4119 122 6801 — Original low speed screw, retained for other modelsTI14/1996 listed configuration · Only the note’s stated models and configuration
  • 4203 122 6802 — New low speed screwTI14/1996 listed configuration · Only the note’s stated models and configuration

Historical fitment · SR 320 / SR 400

SR 320 / 400: dusting kit now includes air filter and prefilter

Same 4203 007 1013 kit number; conversion to dusting or granulate spreading always requires the air-filter change.

  • Section 2 says air filter 4203 141 0300 and prefilter 4203 141 0310 will be included with the dusting and spreading attachment in the future. It is ALWAYS NECESSARY TO CHANGE THE AIR FILTER when converting the unit for DUSTING OR GRANULATE SPREADING; inclusion in a kit does not remove this conversion requirement.
  • The summary retains dusting/spreading attachment 4203 007 1013 in BOTH original and new columns, now explicitly including items 2 and 3. The old columns for air filter 0300 and prefilter 0310 contain dashes; this shows their addition to the kit contents, not proof the parts themselves were newly invented or formerly unavailable. All other parts as before.
  • Introduction is IN PROGRESS, with no serial cutoff or effective date. Remark 1 on the attachment row says only the modified version is available from factory. Remark 2 on BOTH filter rows says the parts are ALREADY IN INVENTORY. Same-number packaging and historical factory availability cannot identify the contents of an older kit or guarantee today’s stock.
  • The source directs the detailed conversion procedure to an instruction sheet SUPPLIED WITH THE ATTACHMENT. This bulletin does not reproduce that sheet or specify its number/edition; no complete conversion sequence is claimed here. The direction to consult the supplied sheet is preserved, rather than inventing installation steps.
  • The retained SCS 01-2012 USA SR320/400 K attachment sheet lists kit 1013 and filters 0300/0310 at positions 17/18. The SR320/400 C sheet lists air filter 0305 at position 15 and the dusting alternatives 0300/0310 at 26/27. TI18 does not universally replace 0305 for every operating mode. The BR C sheet also lists 0300/0310, but this alone does not approve attaching a dusting kit to a blower.
  • The common BR/SR heading is broader than the dusting attachment’s catalog context. This kit note is bound to exact SR320/400 K and C sheets, not BR blowers or later SR340/420 sheets sharing kit 1013. The separate sleeve note retains all four explicitly named models.
  • All three summary rows, both remarks, in-progress statement and all-other-parts line are reviewed. Copyright 1998, D1/MTK-al and documentation 6263 are bibliographic context; they are not production identifiers.
  • Historical source guidance only; no present-day stock or conformity guarantee and no verified physical interchange. No hardware operation was performed.

Source: TI 18/1998, p. 1 — Complete section2, all three summary rows, introduction, both remarks and footer.

Part numbers (3)
  • 4203 007 1013 — Dusting and spreading attachment, including filtersSame number; modified supplied contents · SR 320 / SR 400 dusting or granulate spreading
  • 4203 141 0300 — Air filterAdded to kit contents; already in inventory · SR 320 / SR 400 dusting or granulate conversion
  • 4203 141 0310 — PrefilterAdded to kit contents; already in inventory · SR 320 / SR 400 dusting or granulate conversion

Historical fitment · BR 320 / BR 320 L / BR 400 / SR 320 / SR 400

BR / SR 320, 320 L, 400: Phelon-to-SEM ignition module

SEM 4203 400 1301 starts at serial 2 38 984 310 and has an integral ground contact.

2 38 984 310 — Phelon-to-SEM ignition-module introduction for TI40 models; separate from fuel-cap change

  • Original Phelon module 0000 400 1301 is replaced by SEM 4203 400 1301 from serial 2 38 984 310. This is the ignition cutoff, NOT the cap cutoff 2 39 791 866. The summary repeats both part numbers and the ignition serial; remark1 says the original is no longer available from the factory.
  • The connector-tag shape distinguishes the versions. Figure353TI020 KN labels the original on the LEFT and new on the RIGHT. The original drawing shows a separate ground-wire eyelet; the new module has an integral ground contact, so the ground wire is no longer screwed to the yoke. Do not interpret this as permission to omit grounding or as a complete retrofit wiring procedure.
  • The retained2012 exact BR and SR ignition sheets list module4203 400 1301. Their machine-extracted link to crankcase4203 020 2106 was a cross-column extraction error and is now corrected from original TI19/2001 pages1 and3: later module4203 400 1302 starts at serial2 49 904 357 ONLY with new crankcase4203 020 2106. Module4203 400 1301 remains available for older machines under that later bulletin. This is not an unrestricted retrofit or a replacement of an ignition module by a crankcase. The rest of TI19/2001 remains queued for full semantic review.
  • No flywheel change, ignition timing, air gap, torque, earlier-machine conversion procedure or reverse interchange is specified here. Last TI18.98 and footer6383/copyright1998 are bibliographic context, not extra component cutoffs or missing source dependencies.
  • Historical TI 40/1998, series 4203, heading BR/SR 320, 320 L, 400 only. BR 320 L has an exact retained catalog binding; no separate SR 320 L catalog identity is established from the compressed heading. No extension to 340/380/420 successors, current stock or verified physical interchange is implied. No hardware operation was performed.

Source: TI 40/1998, p. 2 — Complete section2 and353TI020 KN left/right comparison; ignition summary,serial,remark and footer.

Referenced bulletin evidence: TI 19/2001, p. 1 · TI 19/2001, p. 3 — Page1 section1 and adjacent crankcase context;page3 summary items1–2 and remarks1–2; bounded derived-supersession correction only,not whole-page semantic closure.

Part numbers (2)
  • 0000 400 1301 — Original Phelon ignition modulePrevious module; historical factory supply discontinued · BR/SR 320, 320 L, 400 as headed in TI40/1998; exact catalog models listed above
  • 4203 400 1301 — New SEM ignition module with integral ground contactNew ignition module · BR/SR 320, 320 L, 400 as headed in TI40/1998; exact catalog models listed above

Conditional replacement · BR 320 / BR 400 / SR 320 / SR 400

BR/SR 320, 400: two-screw filter housing and cover

Housing 2803 and cover 1002 add a second fastening point; the TI star-grip screw quantity changes from one to two.

in progress — Production introduction announced without a serial threshold.

  • The cover now has a second hole for a second star grip screw; the housing is modified to accept it. The original exploded drawing shows the cover, housing and two fasteners. It supplies no drilling procedure, torque, mixed old/new pairing approval or blanket retrofit claim.
  • The prose replaces housing 4203 140 2800 with 4203 140 2803 and cover 4203 140 1000 with 4203 140 1002. The table splits the old and new housing across two item-1 rows; its dash does not cancel the prose replacement. New housing includes items 2 and 3; cover includes item 3. Do not double-count nested screw contents: remark 2 changes the fastening quantity from 1 to 2.
  • Catalog discrepancy retained: the later SCS 01-2012 BR and SR air-filter sheets list the new housing and cover, but list screw plug 4227 700 2300, quantity 2 (BR position 19, SR position 17), rather than TI star grip screw 4227 700 9300. Neither identity is silently corrected or declared an equivalent/supersession; original catalog rows remain unchanged.
  • The original heading covers BR 320, BR 400, SR 320 and SR 400, series 4203. The shared BR catalog sheet also names BR 320 L; this note does not infer that variant or later 340/380/420 applicability.
  • Both changes are announced as in progress, with no serial threshold. The 1999 factory-supply statements are historical, not present stock claims or proof of the configuration now fitted.

Source: TI 23/1999, p. 1 — 1 Filter housing / Filter cover; complete drawing, summary and remarks.

Part numbers (5)
  • 4203 140 2800 — Filter housingPrevious version; supply while stocks last · Section 1 item 1
  • 4203 140 2803 — Filter housingNew version, including items 2 and 3 · Section 1 item 1
  • 4203 140 1000 — Filter coverPrevious version; supply while stocks last · Section 1 item 2
  • 4203 140 1002 — Filter coverNew version, including item 3 · Section 1 item 2
  • 4227 700 9300 — Star grip screwUnchanged number; quantity 1 to 2 · Section 1 item 3

Wrong number or missing part for the SR 320, SR 400? Report a correction →