Stihl 4221 · Section H · 8 of 20 · 37 parts
Handle
Fits TS 460.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (37)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4221 790 0300 | Handle | 1 |
| 2 | 9371 471 2730 NLA | Cylindrical pin 5x36 | 2 |
| 3 | 0751 030 8958 | Terminal socket 4.8-1 no longer available from factory | 1 |
| 4 | 0751 030 8950 NLA | Terminal socket A 4-1 no longer available from factory | 3 |
| 5 | 0751 030 8470 | Grommet no longer available from factory | 1 |
| 6 | not sold separately | Lead 340 mm / 13.4'' | 1 |
| 7 | 4221 442 1600 | Contact spring | 1 |
| 8 | 4221 442 1601 | Contact spring | 1 |
| 9 | 9075 478 2995 NLA | Pan head self-tapping screw IS-D4x12 | 2 |
| 10 | 4221 180 2000 | Slide control | 1 |
| 11 | 9330 630 0100 | Shake-proof washer 4.3 | 1 |
| 12 | 9039 488 0630 | Self-tapping screw M4x8 | 1 |
| 13 | 4221 182 4505 | Torsion spring | 1 |
| 14 | 4221 182 1000 | Throttle trigger Fitment / change note → | 1 |
| 15 | 4221 180 1100 | Throttle cable | 1 |
| 16 | 4221 182 0800 | Lockout lever Fitment / change note → | 1 |
| 17 | 4221 182 4500 | Torsion spring | 1 |
| 18 | 4221 791 0600 | Handle molding | 1 |
| 19 | 9075 478 4155 | Pan head self-tapping screw IS-D5x24 | 6 |
| 20 | 4221 791 2805 | Annular buffer | 2 |
| 21 | 4116 791 7300 | Plug | 2 |
| 22 | 4221 792 9300 | Rubber buffer | 1 |
| 23 | 4221 791 0605 | AV molding | 1 |
| 24 | 4221 791 1905 | Handlebar support, left | 1 |
| 25 | 4221 791 2800 | Annular buffer | 3 |
| 26 | 4221 792 2000 | Thrust plate | 3 |
| 27 | 9022 341 0975 NLA | Spline screw IS-M5x14 | 9 |
| 28 | 1125 791 7306 | Plug | 3 |
| 29 | 4221 791 1900 | Handlebar support, right | 1 |
| 30 | 4221 791 7600 | Support | 1 |
| 31 | 4221 790 1750 | Handlebar | 1 |
| 32 | not sold separately | Handle hose 450 mm / 17 13/16'' not available as a separate item | 1 |
| 33 | 9074 478 4435 | Pan head self-tapping screw IS-P6x19 | 2 |
| 34 | 0000 967 3702 | Warning pictogram TS | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4221 440 1100 | Short circuit wire | 1 |
| — | 0751 010 1110 | Lead 10 m / 33' | 1 |
| — | 0000 791 2009 | Handle hose Ø 19 mm x 5 m / 3/4x197'' not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 460
TS 460 fuel reservoir, five AV buffers and forward exhaust
0.96 litre tank; separate compensator reservoir returns fuel under negative pressure.
- The fuel tank holds 0.96 litres / 2.02 pt (960 ccm). Its large filler opening is on top of the housing; the TI describes filling in the normal working position, for example with the STIHL filling system. Ease-of-filling wording is not permission to refuel a running or hot engine.
- Tank and compensator reservoir are installed inside the engine housing. Excess tank pressure sends fuel through a connecting hose into the reservoir; negative pressure returns it to the tank. This reservoir is NOT the clean-air pressure compensator on the carburetor.
- The claim that this arrangement prevents fuel or fuel-vapour escape is the historical functional description, not an emissions certification or a leak test performed by this project. Do not backdate the separate 47/1999 tank-vent revision to this 1995 description.
- FIVE rubber buffers on the engine housing separate the handle system from the engine unit and all other assemblies attached to that housing. Vibration reduction is a vendor description, not a measured acceleration value.
- The generously sized exhaust muffler is described as reducing noise effectively, with exhaust gases emitted to the FRONT. This paragraph gives no decibel rating, spark-arrestor approval or muffler part number.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 5 — TS 460 fuel reservoir, five AV buffers and forward exhaust.
No additional parts-table entry added.
Service note · TS 460
TS 460 DG screws: same size does not mean same torque
DG5×24 handle molding and AV molding use 3 Nm; handle/handle uses 8 Nm.
- The TI describes DG screws as self-tapping on first insertion into plastic, permanently forming the material. Its repeated-removal/retightening claim is conditional on maintaining the SPECIFIED TORQUE, making a torque wrench mandatory; it is not evidence that a damaged thread is reusable.
- For a PRE-CUT thread, insert the screw and turn ANTICLOCKWISE until it drops slightly axially into the hole, then turn CLOCKWISE and tighten to the specified torque. This finds the existing thread; cutting another thread would weaken the joint.
- IS-DG5×24: handle molding/handle — 3 Nm; AV molding/handle — 3 Nm; handle/handle — 8 Nm. The 8 Nm value is separately printed and is NOT silently normalized to 3 Nm merely because the size matches.
- IS-M5×14: rubber buffer/engine housing — 8 Nm; rubber buffer/handle bracket — 8 Nm; support/handle bracket — 8 Nm; handle/handle bracket — 8 Nm. IS-M5×20: shroud/engine housing — 6 Nm; carburetor box cover — 6 Nm; starter cover — 6 Nm. These rows do not carry the washer or adhesive footnotes attached to other joints.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 11 — TS 460 DG screws: same size does not mean same torque.
No additional parts-table entry added.
Service note · TS 460
TS 460: same-number trigger revisions retain the interlock check
Cable play may need reduction, then increase again if the interlock check fails.
- Historical TI06/1998 for TS 460, type 4221 only. Later 2012 IPL sheets provide exact-model navigation/comparison, not proof that later carburetor variants share the 1998 settings. No extension to other cut-off machines or saws. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
- Throttle trigger 4221 182 1000 and throttle interlock 4221 182 0800 are MODIFIED with UNCHANGED part numbers to obtain the intended throttle-shutter position. The page2 prose prints a b marker after each number and explicitly says new version in both cases; retain that marker without inventing a different numeric part number or serial cutoff.
- When installing HS275A in an older machine, CHECK throttle-cable play (clearance) and REDUCE it if necessary. THEN CHECK: speed MUST NOT INCREASE when the trigger is actuated WITHOUT depressing the throttle interlock. If necessary INCREASE cable play again. Reducing play alone is not the complete service instruction; no clearance dimension or cable-tension value is supplied.
- In cases of EXCESSIVE WEAR, the trigger AND interlock must also be replaced with the NEW versions. The new trigger and interlock must GENERALLY also be used for older machines with carburetor HS276; this is not limited to machines receiving HS275A.
- Rows11 and12 carry remark3: ONLY MODIFIED versions are factory-available. That is distinct from the starter section’s same-number old-stock rule. EPA series-production timing applies to these control changes; no machine-number cutoff is supplied.
Source: TI 6/1998, p. 2 · TI 6/1998, p. 3 — Sections1.2–1.3 throttle control and summary rows11–12/remark3.
Part numbers (2)
- 4221 182 1000 — Throttle triggerUnchanged number; modified version only · TS 460; only the version and conditions stated here
- 4221 182 0800 — Throttle interlockUnchanged number; modified version only · TS 460; only the version and conditions stated here
Wrong number or missing part for the TS 460? Report a correction →