← TS 460

Stihl 4221 · Section K · 10 of 20 · 41 parts

Carburetor HS-275B

Fits TS 460.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151618192212223242526272829293303132333435363738394404041566789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (41)

PosPart numberDescriptionQty
1 4221 120 0651 Carburetor HS-275B Fitment / change note → 1
1 4221 120 0652 Carburetor HS-275B 1
2 1110 122 9410 Plug 1
3 4221 121 5400 Valve jet 1
4 4221 121 5603 Fixed jet 0.84 1
5 1115 121 2900 Choke shutter 1
6 1110 122 7400 Round head screw 2
7 4221 121 3000 Choke shaft 1
8 1110 129 0900 Gasket 1
9 1110 121 4700 Metering diaphragm 1
10 4221 121 0800 End cover 1
11 1124 122 7102 Screw 4
12 1124 121 4800 Pump diaphragm 1
13 1110 129 1110 Gasket 1
14 1110 121 0810 End cover 1
15 1110 122 7700 Oval head screw 4
16 4223 122 3600 Sealing ring 1
18 4221 122 6801 Low speed adjustment screw 1
19 1110 122 3030 Spring 1
21 1124 121 5000 Inlet control lever Fitment / change note → 1
22 1124 122 3000 Spring → replaced by 1124 122 3001 TI 34/1997 1
23 1110 121 9200 Spindle 1
24 1110 122 7801 Oval head screw 1
25 4116 121 5100 Inlet needle 1
26 4221 121 7800 Strainer 1
27 4221 122 6200 Idle speed adjustment screw 1
28 4221 122 4200 Ball 1
29 1110 122 9005 E-clip 2
30 4221 121 8600 Washer 1
31 4221 122 3200 Torsion spring 1
32 4221 122 9100 Bushing 2
33 4221 120 7101 Throttle shaft with lever Fitment / change note → 1
34 4221 121 8900 Pin 1
35 4221 122 9000 E-clip 1
36 4221 121 3300 Throttle shutter 1
37 4221 121 6150 Choke lever Fitment / change note → 1
38 4221 122 7100 Screw 1
39 4221 122 3201 Torsion spring Fitment / change note → 1
40 4221 122 3605 Sealing ring 2
41 4221 121 9400 Ring 1
Not numbered on the diagram — assemblies, kits and options
— 1124 007 1060 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · TS 460

TS 460: HS275A fixed-jet replacement requires the new choke slide

HS276B is replaced; the fixed jet removes the high-speed adjusting screw.

  • Historical TI06/1998 for TS 460, type 4221 only. Later 2012 IPL sheets provide exact-model navigation/comparison, not proof that later carburetor variants share the 1998 settings. No extension to other cut-off machines or saws. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
  • Original HS276B 4221 120 0602 is replaced by HS275A 4221 120 0651. The new carburetor MUST also be used as replacement for OLDER machines, together with the NEW CHOKE SLIDE. The replacement is not a carburetor-only swap using the old slide.
  • HS275A has a FIXED JET instead of the original semi-fixed jet and high-speed adjusting screw. Drawing 337TI013 GM identifies fixed jet1, inlet control lever2, throttle-shaft lever3, choke lever4 and choke-shaft torsion spring5. All five are changed; these functional callouts are not the page3 table row numbers.
  • The summary introduces the carburetor/control changes with SERIES PRODUCTION OF THE EPA VERSION, without a numeric serial cutoff. Original HS276B complete assembly is NO LONGER AVAILABLE FROM FACTORY (remark2); do not confuse that assembly rule with continued availability of specified HS276 internals under remark1.
  • The later exact TS460 IPL names 4221 120 0651 as HS275B and also lists 4221 120 0652 as HS275B. TI06 names 0651 as HS275A. Preserve this edition/name difference; the identical 0651 number does not establish identical internals or authorize applying the A settings to every B variant.
  • Factory statements about optimum mixture under all operating conditions, smooth running, fuel efficiency, reliability and low emissions are vendor claims, not measurements made here.

Source: TI 6/1998, p. 1 · TI 6/1998, p. 2 · TI 6/1998, p. 3 — Section 1, five functional callouts, section 1.3 carburetor instruction and section 1.6 assembly rows.

Part numbers (2)
  • 4221 120 0602 — Carburetor HS276BOriginal; no longer factory-available in TI · TS 460; only the version and conditions stated here
  • 4221 120 0651 — Carburetor HS275A in TI06/1998New; requires new choke slide · TS 460; only the version and conditions stated here

Conditional replacement · TS 460

TS 460: HS276 internals remain available despite complete-carburetor withdrawal

Five old component rows retain their own availability restriction.

  • Historical TI06/1998 for TS 460, type 4221 only. Later 2012 IPL sheets provide exact-model navigation/comparison, not proof that later carburetor variants share the 1998 settings. No extension to other cut-off machines or saws. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
  • Row3 inlet control lever: 1110 121 5000 → 1124 121 5000. Row4 jet: 4221 121 5600 → 4221 121 5602. The table calls the row Fixed jet, while section1 describes the ORIGINAL as semi-fixed with high-speed adjustment. Both source descriptions are retained.
  • Row5 high-speed adjusting screw 4221 122 6701 has a DASH in the new column: it is omitted from HS275A, not a new adjustable-H setting. Row6 throttle shaft with lever: 4221 120 7100 → 4221 120 7101. Row7 torsion spring: 4221 122 3205 → 4221 122 3201.
  • All five rows carry remark1: ORIGINAL versions remain available for carburetor HS276. That does not contradict withdrawal of the complete HS276B assembly or permit mixing internals into HS275A. The complete-carburetor inclusion range is rows3–10 interpreted with the respective version columns, not every old/new part fitted together.
  • The later HS275B IPL instead lists fixed jet 4221 121 5603, described as 0.84, while TI06 specifies 4221 121 5602 without a jet-size value. Do not substitute the later number or backdate 0.84 to the 1998 jet. Later HS276D internals are not silently substituted for historical HS276B.

Source: TI 6/1998, p. 1 · TI 6/1998, p. 3 — Section 1 fixed versus semi-fixed jet and section 1.6 rows3–7 with remark1.

Part numbers (9)
  • 1110 121 5000 — Inlet control leverOriginal; retained for HS276 · TS 460; only the version and conditions stated here
  • 1124 121 5000 — Inlet control leverNew HS275A version · TS 460; only the version and conditions stated here
  • 4221 121 5600 — JetOriginal; retained for HS276 · TS 460; only the version and conditions stated here
  • 4221 121 5602 — JetNew HS275A version · TS 460; only the version and conditions stated here
  • 4221 122 6701 — High-speed adjusting screwOriginal; retained for HS276 · TS 460; only the version and conditions stated here
  • 4221 120 7100 — Throttle shaft with leverOriginal; retained for HS276 · TS 460; only the version and conditions stated here
  • 4221 120 7101 — Throttle shaft with leverNew HS275A version · TS 460; only the version and conditions stated here
  • 4221 122 3205 — Torsion springOriginal; retained for HS276 · TS 460; only the version and conditions stated here
  • 4221 122 3201 — Torsion springNew HS275A version · TS 460; only the version and conditions stated here

Conditional replacement · TS 460

TS 460: grey choke lever and revised slide are an assembly-only spare

New slide and lever are not separately available replacement parts.

  • Historical TI06/1998 for TS 460, type 4221 only. Later 2012 IPL sheets provide exact-model navigation/comparison, not proof that later carburetor variants share the 1998 settings. No extension to other cut-off machines or saws. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
  • Drawing 337TI011 KN labels ORIGINAL choke lever1 as BLACK and NEW lever2 as GREY. Drawing 337TI012 KN labels original slide1 and new slide2; its arrow points to the changed profile. These two comparison pairs are not spare-part row numbers.
  • Section1.2 modifies the choke-slide profile in addition to the spring and choke-lever profile for a newly defined choke-shutter position. Its word “rewind spring” is retained as source wording; section1 and summary row7 identify the changed spring here as the CHOKE-SHAFT TORSION SPRING, not the separate starter rewind spring.
  • New choke lever assembly 4221 121 6150 includes rows9 and10 (choke lever and choke slide). Original separate lever 4221 121 6100 and slide 4221 121 3200 are NO LONGER AVAILABLE FROM FACTORY under remark2.
  • The new-column -*- symbols for lever and slide mean NOT AVAILABLE SEPARATELY AS REPLACEMENT PARTS; they are not zero quantities, omitted parts or individual new part numbers. Section1.2 says the choke-related parts receive new numbers, but the table only supplies the new assembly number, not separate new lever/slide numbers.
  • The new slide must accompany an HS275A replacement on an older machine. No unrestricted old/new choke mixing or independent slide order number is inferred. Later IPL calls 4221 121 6150 Choke lever; that shortened name does not erase the historical assembly contents.

Source: TI 6/1998, p. 1 · TI 6/1998, p. 2 · TI 6/1998, p. 3 — Choke-lever comparison, sections1.2–1.3, choke-slide drawing and summary rows8–10.

Part numbers (3)
  • 4221 121 6150 — Choke lever assemblyNew; includes lever and slide · TS 460; only the version and conditions stated here
  • 4221 121 6100 — Separate choke leverOriginal; factory withdrawn · TS 460; only the version and conditions stated here
  • 4221 121 3200 — Separate choke slideOriginal; factory withdrawn · TS 460; only the version and conditions stated here

Service note · TS 460

TS 460: HS275A L opens one turn; LA sets 2,500 rpm

Check filter and spark screen before adjustment; use a tachometer.

  • Historical TI06/1998 for TS 460, type 4221 only. Later 2012 IPL sheets provide exact-model navigation/comparison, not proof that later carburetor variants share the 1998 settings. No extension to other cut-off machines or saws. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
  • Check the AIR FILTER and clean or replace it if necessary. Check the SPARK ARRESTING SCREEN and clean or replace it if necessary. Both checks precede the carburetor setting.
  • CAREFULLY screw the low-speed screw L down onto its seat, then open it ONE TURN COUNTERCLOCKWISE (L = 1). No seating torque is specified. This is a seat-based value, not a limiter-stop fraction or an H-screw adjustment.
  • Set engine speed to 2,500 rpm with IDLE-SPEED screw LA; USE A TACHOMETER. The fixed-jet HS275A has no high-speed adjusting screw. No maximum-speed target, H-turn count or altitude correction is given here.
  • The standard setting is bound to the HS275A modification in TI06/1998, not every later HS275B/HS276D configuration shown on the IPL navigation sheets.

Source: TI 6/1998, p. 2 — Section1.1 full standard-setting sequence.

No additional parts-table entry added.

Service note · TS 460

TS 460: EPA label and 50:1 mixture retain the missing TI27 dependency

Delegated emission-system details remain an explicit source gap.

  • Historical TI06/1998 for TS 460, type 4221 only. Later 2012 IPL sheets provide exact-model navigation/comparison, not proof that later carburetor variants share the 1998 settings. No extension to other cut-off machines or saws. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
  • The factory applies the illustrated U.S. EPA Phase1 label to machines conforming to the stated standard. Drawing000TI013 KN is a TEMPLATE with engine-family/type/displacement/manufacture-date fields, not identified machine data or a complete label order number. Its general Owner’s Manual maintenance/adjustment reference does not identify an edition.
  • The EPA permit was obtained with a fuel-oil mixture of 50:1. Further fuel details and Federal Emission Control Systems Utility Engines explicitly refer to TI27/1997. That source is absent from the retained690TIs and the bounded current766-PDF filename inventory reverified here; the delegated details remain a SOURCE GAP, not fabricated warranty terms, emission measurements or legal permission.
  • This TI reproduces its standard setting and the throttle-interlock check. No separate manual edition is inferred from the generic label. The cover’s compliance claim is a vendor statement for the described modification, not present-day certification of an owner’s machine.

Source: TI 6/1998, p. 1 · TI 6/1998, p. 2 — Cover emission statement/label and sections1.4–1.5.

No additional parts-table entry added.

Wrong number or missing part for the TS 460? Report a correction →