Stihl 4223 · Section K · 10 of 22 · 40 parts
Carburetor HS-279D
Fits TS 400.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (40)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4223 120 0650 | Carburetor HS-279D Fitment / change note → | 1 |
| 1 | 4223 120 0651 | Carburetor HS-279D | 1 |
| 2 | 4223 121 0800 | End cover | 1 |
| 3 | 1110 122 7700 | Oval head screw | 4 |
| 4 | 1110 129 1110 | Gasket | 1 |
| 5 | 1124 121 4800 | Pump diaphragm | 1 |
| 6 | 4221 121 7800 | Strainer | 1 |
| 7 | 4116 121 5100 | Inlet needle | 1 |
| 8 | 1124 121 5000 | Inlet control lever Fitment / change note → | 1 |
| 9 | 1110 121 9200 | Spindle | 1 |
| 10 | 1110 122 7801 | Oval head screw | 1 |
| 11 | 1124 122 3000 | Spring → replaced by 1124 122 3001 TI 34/1997 | 1 |
| 12 | 1115 121 0800 | End cover | 1 |
| 13 | 1106 122 7400 | Round head screw | 4 |
| 14 | 1110 121 4700 | Metering diaphragm | 1 |
| 15 | 1110 129 0900 | Gasket | 1 |
| 16 | 1110 122 9410 | Plug | 1 |
| 17 | 4223 121 5400 | Valve jet | 1 |
| 18 | 4221 122 6200 | Idle speed adjustment screw | 1 |
| 19 | 4221 122 4200 | Ball | 1 |
| 20 | 4221 122 6801 | Low speed adjustment screw Fitment / change note → | 1 |
| 21 | 1110 122 3030 | Spring | 1 |
| 22 | 4223 122 3600 | Sealing ring | 2 |
| 25 | 4221 122 7100 | Screw | 1 |
| 27 | 4223 120 7200 | Choke shaft | 1 |
| 28 | 4223 121 2900 | Choke shutter | 1 |
| 29 | 1110 122 7400 | Round head screw | 1 |
| 30 | 4221 122 3605 | Sealing ring | 2 |
| 31 | 4221 121 9400 | Ring | 2 |
| 32 | 1110 122 9005 | E-clip | 2 |
| 33 | 4223 122 3000 | Spring | 1 |
| 34 | 4223 120 7101 | Throttle shaft with lever Fitment / change note → | 1 |
| 35 | 4223 122 3200 | Torsion spring | 1 |
| 36 | 4221 121 8600 | Washer | 1 |
| 37 | 1110 122 9005 | E-clip | 1 |
| 38 | 4223 121 3300 | Throttle shutter | 1 |
| 39 | 1110 122 7400 | Round head screw | 1 |
| 40 | 4223 121 3500 | Throttle lever Fitment / change note → | 1 |
| 41 | 4223 121 5603 | Fixed jet 0.75 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1124 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · TS 400
TS 400: HS279B is the complete replacement even for older machines
The fixed-jet EPA carburetor replaces complete HS274 units, including non-EPA applications.
- Historical TI04/1998 for TS 400, type 4223 only. Later 2012 IPL sheets are navigation/comparison, not evidence that their later versions equal the 1998 configuration. No extension to Japan-specific carburetors, other cut-off machines or saws. Historical factory availability is not current stock. No hardware operation was performed.
- Original HS 274 carburetor 4223 120 0600 is replaced by HS 279 B 4223 120 0650. The new carburetor has NO H adjusting screw. Drawing 338TI012 KN contrasts old H/L/LA with new L/LA; the diagram caption abbreviates the new name to HS 279 without changing the prose designation.
- Section 2 requires HS 279 B when replacing the COMPLETE carburetor, even in older machines. Section 1 remark 2 calls it a GENERAL SPARE PART, also for machines WITHOUT EPA permit. This is not an EPA-only replacement restriction. New choke lever 4223 121 6101 is included. Original complete HS274 is no longer required as a spare (remark 1); individual-parts rules are separate.
- Item 1 says HS279B includes items 2–8 and 13, but original-only items 4 (H screw) and 7 (0.64 jet) have dashes in the new column. The broad inclusion heading does not install these old-only parts in the new carburetor.
- Introduction is continuous for section 1; no HS279B serial cutoff is supplied. The X 38 434 327 cutoff belongs to the intermediate HS274C introduction, not HS279B.
- Factory mixture, smooth running, economy, reliability and low emissions are vendor statements, not measured results here. Later IPL calls 4223 120 0650 HS-279D and lists 0.75 jet 4223 121 5603, whereas this TI specifies HS279B and 0.73 jet 4223 121 5602. Preserve that version difference, not an inferred jet substitution.
Source: TI 4/1998, p. 1 · TI 4/1998, p. 2 · TI 4/1998, p. 3 — Section 1, summary assembly rows/remarks 1–2 and section 2 supply of spare parts.
Part numbers (3)
- 4223 120 0600 — Complete HS274 carburetorOriginal assembly · TS 400; only the version and conditions stated here
- 4223 120 0650 — Complete HS279B carburetorGeneral replacement · TS 400; only the version and conditions stated here
- 4223 121 6101 — Choke leverIncluded new lever · TS 400; only the version and conditions stated here
Service note · TS 400
TS 400: HS279B standard setting and emission reference
L opens one turn from its seat; LA sets 2,500 rpm using a tachometer.
- Historical TI04/1998 for TS 400, type 4223 only. Later 2012 IPL sheets are navigation/comparison, not evidence that their later versions equal the 1998 configuration. No extension to Japan-specific carburetors, other cut-off machines or saws. Historical factory availability is not current stock. No hardware operation was performed.
- Check the air filter and clean or replace it if necessary. Check the spark-arresting screen and clean or replace it if necessary. Carefully screw L down onto its seat, then open ONE TURN counterclockwise (L = 1). Use LA to set 2,500 rpm; USE A TACHOMETER. This is a seat-based setting for HS279B, not a lean-stop/capped setting or an HS274 H-screw instruction.
- Drawing 338TI013 KN shows L above LA in the two-opening access area; no H adjustment or maximum-speed value is supplied. No setting is inferred for a different carburetor bearing the same complete-assembly number.
- The EPA permit was obtained with 50:1 fuel-oil mixture. The cover says conforming machines receive the illustrated U.S. EPA Phase 1 label (000TI013 KN); its variable fields are a template, not identified machine data or a complete order number.
- Both fuel/emission details and Federal Emission Control Systems Utility Engines delegate to TI27/1997. That source is absent from the retained 690 TIs and the bounded current 766-PDF inventory. Details remain a documented source gap; no emission measurements, warranty terms or legal permission are inferred.
Source: TI 4/1998, p. 1 · TI 4/1998, p. 2 — Cover label and sections 1.1–1.3 with screw-access drawing.
No additional parts-table entry added.
Conditional replacement · TS 400
TS 400: HS279B metering and throttle component assignments
All section 1 carburetor component rows retain their old/new columns and supply restrictions.
- Historical TI04/1998 for TS 400, type 4223 only. Later 2012 IPL sheets are navigation/comparison, not evidence that their later versions equal the 1998 configuration. No extension to Japan-specific carburetors, other cut-off machines or saws. Historical factory availability is not current stock. No hardware operation was performed.
- Row 2 inlet control lever: 1110 121 5000 → 1124 121 5000. Row 3 low-speed screw: 4223 122 6800 → 4221 122 6801. Row 4 high-speed screw: 4223 122 6700 → no new counterpart.
- Row 5 throttle shaft with lever: 4223 120 7100 → 4223 120 7101. Row 6 throttle lever: 4223 123 7300 → 4223 121 3500.
- Row 7 fixed jet 0.64: 4205 121 5600 → no new counterpart. Row 8 fixed jet 0.73: no old counterpart → 4223 121 5602. Do not treat the old 0.64 as the new fixed jet.
- Row 13 choke lever: 4223 121 6100 → 4223 121 6101. The new lever is included with the replacement carburetor.
- Remark 3 keeps original rows 2,4,5,6,7 available for older machines. Remark 4 says original low-speed screw row 3 and choke lever row 13 are no longer factory-available; section 2 governs the low-speed screw exception. Unlisted carburetor parts refer to section 2. Version assignments do not permit arbitrary mixed internals.
Source: TI 4/1998, p. 2 — Section 1.5 rows 2–8,13 and remarks 3–4.
Part numbers (13)
- 1110 121 5000 — Inlet control leverOriginal version · TS 400; only the version and conditions stated here
- 1124 121 5000 — Inlet control leverNew version · TS 400; only the version and conditions stated here
- 4223 122 6800 — Low-speed screwOriginal version · TS 400; only the version and conditions stated here
- 4221 122 6801 — Low-speed screwNew version · TS 400; only the version and conditions stated here
- 4223 122 6700 — High-speed screwOriginal version · TS 400; only the version and conditions stated here
- 4223 120 7100 — Throttle shaft with leverOriginal version · TS 400; only the version and conditions stated here
- 4223 120 7101 — Throttle shaft with leverNew version · TS 400; only the version and conditions stated here
- 4223 123 7300 — Throttle leverOriginal version · TS 400; only the version and conditions stated here
- 4223 121 3500 — Throttle leverNew version · TS 400; only the version and conditions stated here
- 4205 121 5600 — Fixed jet 0.64Original version · TS 400; only the version and conditions stated here
- 4223 121 5602 — Fixed jet 0.73New version · TS 400; only the version and conditions stated here
- 4223 121 6100 — Choke leverOriginal version · TS 400; only the version and conditions stated here
- 4223 121 6101 — Choke leverNew version · TS 400; only the version and conditions stated here
Wrong number or missing part for the TS 400? Report a correction →