← HS 72, HS 74, HS 76 · HS 75, HS 80, HS 85

Stihl 4226 · Section A · 1 of 17 · 22 parts

Crankcase

Fits HS 75, HS 80, HS 85.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121213141516171819220212222334456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (22)

PosPart numberDescriptionQty
1 4137 020 2800 Crankcase, starter side 1
2 0000 988 8600 Sleeve 2
3 9503 003 0242 Grooved ball bearing 6201 1
4 9640 003 1195 Oil seal 12x22x5 2
5 4137 020 2600 Crankcase, fan side 1
6 4137 030 0401 Crankshaft 1
7 9022 341 1050 Spline screw IS-M5x25 3
8 4137 020 1201 Cylinder with piston Ø 34 mm Fitment / change note → 1
9 4137 030 2010 Piston Ø 34 mm 1
10 4137 034 3000 Piston ring Ø 34x1.5 mm 2
11 4137 034 1500 Piston pin 8x5x22 1
12 9463 650 0805 Snap ring 8x0.7 2
13 9512 003 1830 Needle cage 8x11x10 1
14 4137 029 2300 Cylinder gasket 1
15 9075 478 4159 Pan head self-tapping screw IS-D5x24 4
16 0783 830 2000 Tube of sealant Dirko HT red option 1
17 4226 149 0605 Muffler gasket 1
18 4226 140 0603 Muffler 1
19 4226 140 0602 Muffler 1
20 4137 141 9000 Screen 1
21 9099 021 0810 Self-tapping screw 4.2x9.5 1
22 9022 341 0980 Spline screw IS-M5x16 3

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · HS 75 / HS 80 / HS 85

HS 75/80/85: chrome-bore replacement cylinder

The previous-generation chrome-bore cylinder replaces the Nikasil version; no C1Q-S63 conversion is stated.

  • Section 2.1.1 explicitly applies the section 2.1 chrome-bore replacement to HS 75, 80, 85, introduced in production and parts support. Cylinder with piston 4137 020 1201 is interchangeable with previous Nikasil-bore 4137 020 1200; future replacement supply is 1201, with 1200 available only while stocks last.
  • This HS subsection does not assign new-port cylinder 4137 020 1202 or the C1Q-S63 carburetor to these hedge trimmers. Do not propagate the FS 85 cutoff to HS models. Included parts remain as before; no HS serial cutoff is printed here.
  • Only explicitly named models and configurations are covered. Shared IPL pages do not extend these assertions to unnamed R/RX or other variants. Availability statements describe 2001 factory support, not present stock. The printed cover places FH/HL under 4230, HT under 4138 and KW under 4602; retained exact-model engine sheets use 4137 as navigation, not proof of series equivalence.

Source: TI 16/2001, p. 2 · TI 16/2001, p. 3 — Sections 2.1, 2.1.1 and 2.2: HS-specific previous-generation cylinder supply.

Part numbers (2)
  • 4137 020 1200 — Cylinder and piston, Nikasil borePrevious · HS 75, HS 80, HS 85; named configuration only
  • 4137 020 1201 — Cylinder and piston, chrome boreInterchangeable previous-generation replacement · HS 75, HS 80, HS 85; named configuration only

Service note · HS 75 / HS 80 / HS 85

HS 75/HS 80/HS 85: new powerhead and engine specification

25.4 cm³, 34 x 28 mm, 0.9 kW; predecessor replacement does not establish parts interchange.

  • HS 75, 80 and 85 replace HS 72, 74 and 76 for the same applications and user groups, with greater torque and power. Five-part crankshaft interconnected against twisting; four-channel transfer ports improve mixture preparation, combustion and emissions; larger cylinder cooling area.
  • Improved air-filter material and larger filter volume; twin-chamber exhaust muffler with easier spark-arresting-screen installation/removal; ElastoStart handle for softer starting. Intake noise is muffled. No one-to-one old/new part compatibility is stated.
  • Engine displacement 25.4 cm³ (1.55 cu. in), bore 34 mm (1.34 in), stroke 28 mm (1.10 in), ISO 8893 power 0.9 kW (1.2 HP). Page 3 delegates maximum and idle speeds to the carburetor table, but page 4 supplies only 2800 rpm idle and screw settings, NOT a numeric maximum speed. Do not invent a maximum or copy the BG75 fanwheel-load exception.
  • Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 17/1996, p. 1 · TI 17/1996, p. 2 · TI 17/1996, p. 3 — new powerhead and engine specification.

No additional parts-table entry added.

Service note · HS 75 / HS 80 / HS 85

HS 75/HS 80/HS 85: seal puller conversion and service aids

20 mm longer spindle converts previous puller; predecessor tools and repair times referenced.

  • Puller 5910 890 4400 and spindle 5910 890 8400 are listed for oil seals under the printed “Axial face seal” heading. Replacing the former spindle in puller 0000 890 4400 with spindle 5910 890 8400, which is 20 mm LONGER, makes it identical to 5910 890 4400. This is spindle replacement, not alteration of the puller body.
  • Other repairs use the usual tools as for HS72/74/76. Repair times are the same as those predecessors, but no durations or full tool list supplied. Gasket panel 0457 281 4203 is a service aid, not an identified pre-cut gasket. A separate parts list is referenced; exact-model IPL data is locally available.
  • Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 17/1996, p. 1 · TI 17/1996, p. 5 · TI 17/1996, p. 7 — seal puller conversion and service aids.

Part numbers (4)
  • 5910 890 4400 — Oil-seal pullerTI17/1996 listed item · HS75/80/85 service tool
  • 5910 890 8400 — 20 mm longer spindleTI17/1996 listed item · Conversion of 0000 890 4400
  • 0000 890 4400 — Previous pullerTI17/1996 listed item · Comparison/conversion only
  • 0457 281 4203 — Gasket panelTI17/1996 listed item · Service aid

Service note · HS 75 / HS 80 / HS 85

HS 75/HS 80/HS 85: leak-test pressures and safety prerequisite

Crankcase pressure/vacuum 0.5 bar; inlet needle pressure 0.6 bar.

  • Crankcase leakage test: pressure +0.5 bar and vacuum magnitude 0.5 bar; the latter is not 0.5 bar absolute. Carburetor inlet needle test: pressure +0.6 bar. Do not exchange crankcase and carburetor test values.
  • The TI provides no hold duration, permitted decay or complete test setup. Starting during maintenance/repair requires national safety regulations and the Instruction Manual safety instructions. Exact Instruction Manual dependency is not supplied by this TI; the available service manual is not a substitute for that exact source.
  • Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 17/1996, p. 1 · TI 17/1996, p. 5 — leak-test pressures and safety prerequisite.

No additional parts-table entry added.

Service note · HS 75 / HS 80 / HS 85

HS 75/HS 80/HS 85: shared component tightening torques

Seventeen shared values; ambiguous crankcase row and fastener-specific distinctions retained.

  • All values Nm. IS-M5x25 crankcase 9.5; second IS-M5x25 row prints “Crankcase” and “Crankcase spacer flange/cylinder”, with 5.5 aligned to the latter. Ambiguous two-line label retained, not a wholesale change of crankcase torque to 5.5. IS-DG5x24 cylinder/crankcase 9.5.
  • IS-M4x16 brake band/gear housing 3.5 and gearbox cover/gear housing 3.5. IS-M5x16 muffler/cylinder 9.5; air cowling/gear housing 5.5; gear housing/crankcase 5.5; starter cover/crankcase 5.5; muffler/crankcase 9.5.
  • M8 starter carrier 20.0 (no fastener designation supplied); M8 clutch nut 21.0. IS-M4x20 ignition module/cylinder 4.5; plastoform IS-P5.5x12 rope rotor in starter cover 3.5. IS-M5x16 cutting blade 9.5; IS-M5x25 eccentric lever/gear housing 5.5; M14x1.25 spark plug 20.0.
  • The other six table values are model-specific blade-guide, rubber-buffer and handle rows, recorded separately. No lubricated-thread condition or tightening sequence specified; shared thread size does not establish shared torque. No component/fastener part number invented.
  • Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 17/1996, p. 1 · TI 17/1996, p. 7 — shared component tightening torques.

No additional parts-table entry added.

Wrong number or missing part for the HS 75, HS 80, HS 85? Report a correction →