Stihl 4226 · Section B · 2 of 17 · 30 parts
Rewind starter, Ignition system
Fits HS 75, HS 80, HS 85.
Historical fitment & changes (12) — includes parts and conditions not shown on this drawing.
Parts (30)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4133 190 2002 | Carrier | 1 |
| 2 | 4133 195 7201 | Pawl | 1 |
| 3 | 0000 998 0612 | Torsion spring | 1 |
| 4 | 4226 190 0400 | Starter cover | 1 |
| 5 | 4226 791 7200 | Sleeve | 3 |
| 6 | 4137 190 1100 | Rope rotor with rewind spring Fitment / change note → | 1 |
| 7 | 0000 190 3403 | Starter grip ElastoStart Ø 2,7 mm Fitment / change note → | 1 |
| 8 | 4137 195 8200 | Starter rope Ø 2.7x910 mm Fitment / change note → | 1 |
| 9 | 0000 195 7000 | Cap | 1 |
| 10 | 9104 003 0960 | Self-tapping screw P5.5x12 | 1 |
| 11 | 4226 141 0301 | Prefilter | 1 |
| 12 | 4226 967 1510 | Model plate HS 75 | 1 |
| 13 | 4226 967 1511 | Model plate HS 80 | 1 |
| 14 | 4226 967 1512 | Model plate HS 85 | 1 |
| 15 | 0000 967 2128 | Nameplate MADE IN GERMANY | 1 |
| 16 | 0000 967 2129 | Nameplate MADE IN USA | 1 |
| 17 | 9022 341 0980 | Spline screw IS-M5x16 | 3 |
| 19 | 4137 400 1350 | Ignition module Fitment / change note → | 1 |
| 20 | 1106 405 1000 | Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 | 1 |
| 21 | 0000 998 0606 | Torsion spring | 1 |
| 22 | 4137 404 9300 | Washer Fitment / change note → | 2 |
| 23 | 4137 405 1600 | Plug connector | 1 |
| 24 | 9291 021 0121 | Washer 5.3 Fitment / change note → | 1 |
| 25 | 9022 371 0710 | Spline screw IS-M4x20 Fitment / change note → | 2 |
| 26 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 26 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 27 | 4226 160 2000 | Clutch | 1 |
| 28 | 4226 162 7900 | Tension spring | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4226 190 4006 | Rewind starter | 1 |
| — | 0000 930 2281 | Starter rope Ø 2.7 mm x 30.8 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HS 75 / HS 80 / HS 85
HS 75 / HS 80 / HS 85: series 4226 replacement ignition assignment
Blank module/flywheel cells; no pairing inferred. ignition lead not replaceable.
- Printed series 4226. Both ignition-module and flywheel cells are blank in the HS 75 / HS 80 / HS 85 row. Full horizontal lines separate it from both neighboring rows; no shared pairing is established. Do not borrow the HL 75 / FH 75 combination.
- The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.
No additional parts-table entry added.
Conditional replacement · HS 75 / HS 80 / HS 85
HS 75/80/85: AD ignition requires revised guard or cover
HS 75/80 use the new hand guard; HS 85 uses the new cover. MB replacement kit remains available.
- Identify the module by its two-letter vendor type code and the final four STIHL part-number digits: AD (1304) versus MB (1307). A longer spark duration is the vendor-stated operating-range benefit, not a reproduced measurement. No complete AD ordering number is printed; do not derive one from 1304.
- Type MB4137 400 1307 was no longer supplied separately; kit 4137 400 1350 includes the MB module, mounting hardware and illustrated installation instructions and replaces either MB or AD. AD was not yet available as a spare. The page 8 drawing shows different mounting sequences for AD and MB; use the version-specific instructions, not an assumed common washer stack. Separate kit instructions were not located in the retained inventory. Later general ignition procedures do not establish the AD/MB-specific mounting stack; this remains a documented source gap.
- The summary retains two washers 4137 404 9300 and insulating tube 4137 442 0400, lists two new A5.3 washers 9291 021 0121, and changes two IS-M4 x 20 screws from 9022 313 0710 to 9022 371 0710. Old screws remain spares for other models. Insulating tube is not required for BG 75 or HS 75/80/85. No torque or air gap is specified here.
- Ignition introduction is model-specific: HS 80 from 2 49 943 796; FS 85 from 2 49 848 196; HT 75 from 2 50 062 280; other models in progress. These are not model production ranges or a universal update cutoff. Chapter 1 prints a different FS 85 update serial 2 49 849 196; retain both without replacing the ignition-specific statement.
- HS 75/80 AD(1304) installation requires hand guard 4226 792 9102, replacing 4226 792 9110. HS 85 AD(1304) requires cover 4226 792 2701, replacing 4226 792 2700. These are mandatory pairings for AD, not a requirement to replace guards whenever an MB kit is used. Old guards/covers were supplied only while stocks lasted. Only HS 80 has a printed ignition cutoff; none is assigned to HS 75 or HS 85.
- Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.
Source: TI 16/2001, p. 8 · TI 16/2001, p. 9 — Sections 4.2.1 and 4.4: HS guards and cover; common kit restrictions.
Part numbers (11)
- 4137 400 1307 — Ignition module type MBPrevious separate module · HS 75, HS 80, HS 85; named configuration only
- 4137 400 1350 — Type MB ignition module kitReplacement for MB and AD · HS 75, HS 80, HS 85; named configuration only
- 4137 404 9300 — Washer, twoUnchanged · HS 75, HS 80, HS 85; named configuration only
- 4137 442 0400 — Insulating tubeUnchanged; omitted on BG 75 and HS 75/80/85 · HS 75, HS 80, HS 85; named configuration only
- 9291 021 0121 — Washer A5.3, twoNew mounting hardware · HS 75, HS 80, HS 85; named configuration only
- 9022 313 0710 — Screw IS-M4 x 20, twoPrevious; retained for other models · HS 75, HS 80, HS 85; named configuration only
- 9022 371 0710 — Screw IS-M4 x 20, twoNew · HS 75, HS 80, HS 85; named configuration only
- 4226 792 9110 — HS 75/80 hand guardPrevious · HS 75 and HS 80 only; Previous
- 4226 792 9102 — HS 75/80 hand guardRequired with AD · HS 75 and HS 80 only; Required with AD
- 4226 792 2700 — HS 85 coverPrevious · HS 85 only; Previous
- 4226 792 2701 — HS 85 coverRequired with AD · HS 85 only; Required with AD
Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85 / HS 72 / HS 74 / HS 76
TI24/2002: three starter-rope stages and model scope
Keep the original, interim and final rope sizes separate; HS72/74/76 do not inherit the grip change.
- Original starter rope 4123 195 8200 is 0.105 in / 2.7 mm diameter and 31.5 in / 800 mm long. Interim rope 0000 195 8200 is 0.120 in / 3 mm diameter and the same 31.5 in / 800 mm length. Final rope 4137 195 8200 returns to 0.105 in / 2.7 mm diameter but increases length to 35.8 in / 910 mm. Do not confuse unchanged diameter with unchanged length.
- The interim rope is included in ElastoStart 0000 190 3400; the final rope is used in ElastoStart 0000 190 3403. Those grip associations describe the main starter branch; section 2.7 extends subsections 2.1, 2.3, 2.4 and 2.5 to HS 72, HS 74 and HS 76, but not subsection 2.2. No ElastoStart-grip replacement is authorized for those three models by this TI.
- Summary remarks distinguish earlier-to-interim from interim-to-new changes. Original rope 4123 195 8200 and interim rope 0000 195 8200 remain available for other models; their removal from this branch does not mean universal discontinuation. Section 2.6 states the new starter parts are fully interchangeable with previous machine versions within the applicable section 2 model scope.
- These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.
Part numbers (3)
- 4123 195 8200 — Starter rope 2.7 x 800 mmOriginal; retained for other models · Named section 2 models only; see conditions
- 0000 195 8200 — Starter rope 3 x 800 mmInterim; retained for other models · Named section 2 models only; see conditions
- 4137 195 8200 — Starter rope 2.7 x 910 mmFinal version · Named section 2 models only; see conditions
Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85
TI24/2002: ElastoStart grip change excludes HS72/74/76
The new grip follows the longer final rope; do not extend subsection2.2 to the restricted hedge-trimmer group.
- ElastoStart grip 0000 190 3403 replaces 0000 190 3400 together with the introduction of final rope 4137 195 8200 (2.7 x 910 mm). The old grip includes interim rope 0000 195 8200 (3 x 800 mm); the new grip includes the final rope. Summary rows 4–7 preserve these assembly contents.
- The old grip and interim rope remain available for other models. Full starter modifications also apply to BG 72, BG 75, FC 72, FS 72, FS 74, FS 76, HS 75, HS 80 and HS 85. HS 72, HS 74 and HS 76 are deliberately excluded from this grip note: their subsection list omits 2.2.
- The section 2.6 interchangeability statement belongs to this starter update; it does not remove the explicit model/subsection limitation or the separate control-handle retrofit conditions.
- These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.
Part numbers (4)
- 0000 190 3400 — ElastoStart grip with interim ropePrevious; retained for other models · Named section 2 models only; see conditions
- 0000 190 3403 — ElastoStart grip with final ropeNew · Named section 2 models only; see conditions
- 0000 195 8200 — Starter rope 3 x 800 mmOld grip content · Named section 2 models only; see conditions
- 4137 195 8200 — Starter rope 2.7 x 910 mmNew grip content · Named section 2 models only; see conditions
Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85 / HS 72 / HS 74 / HS 76
TI24/2002: rope rotor and spring supplied as an assembly
Preserve the interim-rotor availability conflict; new rotor and spring are not separate spares.
- Original rope rotor 4133 195 0400 was replaced by interim rotor 4133 195 0470. The TI says the interim rotor is no longer available separately and the rewind spring 4133 195 1600 is likewise supplied only as part of rope rotor with rewind spring 4137 190 1100. The new assembly contains the rotor and spring; no independent new numbers are given for either component.
- The starter drawing labels rope (1), ElastoStart grip (2), rotor (3), spring (4), and rotor/spring assembly (5). These are not the summary-table row numbers: assembly 4137 190 1100 is summary item 8, with its spring and rotor as items 9 and 10.
- Preserved source tension: prose and summary remark 4 say the interim rotor is no longer available from the factory, while summary item 10 (previous rotor 4133 195 0470) carries remark 3 permitting previous stock until exhausted. Spring item 9 also carries the stock remark despite prose saying it is no longer separate. New separate items are explicitly unavailable under remark 6; use assembly item 8. Do not silently collapse these phase/stock statements into a current availability promise.
- Section 2.7 explicitly extends subsections 2.3–2.5, as well as rope subsection 2.1, to HS 72, HS 74 and HS 76. The broader group receives all starter modifications. Section 2.6 states full interchangeability with previous versions within this starter scope, not a control-handle equivalence rule. All other parts are stated unchanged.
- These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.
Part numbers (4)
- 4133 195 0400 — Rope rotorOriginal; stocks-only phase · Named section 2 models only; see conditions
- 4133 195 0470 — Rope rotorInterim; conflicting separate-stock statements · Named section 2 models only; see conditions
- 4133 195 1600 — Rewind springPrevious separate part; stock/assembly statements retained · Named section 2 models only; see conditions
- 4137 190 1100 — Rope rotor with rewind springNew assembly; includes both components · Named section 2 models only; see conditions
Service note · HS 75 / HS 80 / HS 85
HS 75/HS 80/HS 85: starter rope and spring reserve
Single pawl, 3.0 x 800 mm rope; seven rotor turns and at least half-turn reserve.
- Single-pawl ElastoStart mechanism. Rope diameter 3.0 mm (0.12 in), length 800 mm (31.5 in). Rewind spring tension SEVEN turns of rope rotor; reserve pull AT LEAST 1/2 turn, not seven engine revolutions.
- Current HS75/80/85 IPL lists 2.7 x 910 mm rope and a 2.7 mm ElastoStart grip. That edition difference does not supersede the TI specification or prove interchangeable rope/grip combinations.
- Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 17/1996, p. 1 · TI 17/1996, p. 3 — starter rope and spring reserve.
No additional parts-table entry added.
Service note · HS 75 / HS 80 / HS 85
HS 75/HS 80/HS 85: ignition data and electrode-gap conflict
Bosch WSR6F; printed 0.5 mm / 0.20 in gap is contradictory.
- Air gap 0.2–0.5 mm (0.008–0.019 in). Timing 1.55–2.25 mm (0.061–0.089 in) BEFORE TDC at 8000 rpm. Ignition lead length 160 mm. Suppressed Bosch WSR6F spark plug, heat range 200, thread M14 x 1.25, length 9.5 mm.
- Electrode gap prints 0.5 mm (0.20 in). These values conflict by roughly a factor of ten; the scan confirms 0.20, not an extraction error. Preserve both, do not silently correct the inch value or treat it as a verified gap.
- Current IPL also lists NGK BPMR7A, but TI17/1996 specifies Bosch only. No cross-brand equivalence, supersession, measured timing or hardware verification inferred.
- Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 17/1996, p. 1 · TI 17/1996, p. 4 — ignition data and electrode-gap conflict.
No additional parts-table entry added.
Service note · HS 75 / HS 80 / HS 85
HS 75/HS 80/HS 85: shared component tightening torques
Seventeen shared values; ambiguous crankcase row and fastener-specific distinctions retained.
- All values Nm. IS-M5x25 crankcase 9.5; second IS-M5x25 row prints “Crankcase” and “Crankcase spacer flange/cylinder”, with 5.5 aligned to the latter. Ambiguous two-line label retained, not a wholesale change of crankcase torque to 5.5. IS-DG5x24 cylinder/crankcase 9.5.
- IS-M4x16 brake band/gear housing 3.5 and gearbox cover/gear housing 3.5. IS-M5x16 muffler/cylinder 9.5; air cowling/gear housing 5.5; gear housing/crankcase 5.5; starter cover/crankcase 5.5; muffler/crankcase 9.5.
- M8 starter carrier 20.0 (no fastener designation supplied); M8 clutch nut 21.0. IS-M4x20 ignition module/cylinder 4.5; plastoform IS-P5.5x12 rope rotor in starter cover 3.5. IS-M5x16 cutting blade 9.5; IS-M5x25 eccentric lever/gear housing 5.5; M14x1.25 spark plug 20.0.
- The other six table values are model-specific blade-guide, rubber-buffer and handle rows, recorded separately. No lubricated-thread condition or tightening sequence specified; shared thread size does not establish shared torque. No component/fastener part number invented.
- Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 17/1996, p. 1 · TI 17/1996, p. 7 — shared component tightening torques.
No additional parts-table entry added.
Service note · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85
Nine models: paired carburetor and electronic speed-limitation change
Keep each printed X-prefixed introduction number tied to its exact model.
FC 75: X 37 801 959; FS 75: X 37 878 261; FS 80: X 37 759 999; FS 85: X 37 838 653; HL 75: X 37 761 799; HS 75, HS 80 and HS 85: X 37 810 310; HT 75: X 37 772 428 — Exact model-conditioned introduction of the paired production change; not a continuous model identity range.
- At the listed machine numbers the production carburetor WITH SPEED CONTROL VALVE (drawing 3, arrow) changes to a version WITHOUT it (drawing 4), AT THE SAME TIME as introduction of an ignition module with ELECTRONIC SPEED LIMITATION (ESL). Removing the valve alone is not the described change.
- FC 75: X 37 801 959; FS 75: X 37 878 261; FS 80: X 37 759 999; FS 85: X 37 838 653; HL 75: X 37 761 799; HS 75, HS 80 and HS 85: X 37 810 310; HT 75: X 37 772 428. These are model-conditioned introduction markers, not model-identification intervals; retain the printed X prefix. BG 75 has NO entry in this table. FS 80 here is TYPE 4137, not the older type 4112 FS 80.
- The page2 table is actually headed1.3.1, while the summary refers to1.2.1; this numbering inconsistency is preserved, not a missing table. Section 1.2.2.3 keeps the individual maximum-speed ranges and carburetor settings UNCHANGED, with no numeric values supplied.
- Cover types: BG 75 4227; HS 75/80/85 4226; HL 75 4230; HT 75 4138; FS 75/80/85 and FC 75 4137. The catalog groups HL/HT power-unit sheets under 4137; that folder is not a correction to the cover type identities. Service replacement carburetors follow separate rules below.
- Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.
Source: TI 41/1997, p. 1 · TI 41/1997, p. 2 · TI 41/1997, p. 4 — Section 1.2, complete introduction table and drawing 366TI020 KN; section 1.2.2.3; cover types.
No additional parts-table entry added.
Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85
ESL ignition modules: 1306/1307 marking and the optional BG/HS hose
1307 adds the insulating hose and is the general replacement.
- WHEN DISASSEMBLED, marking XXXX = 1306 OR 1307 identifies an ESL module. Drawing366TI021 KN reads STIHL 4137 XXXX A and calls the hose5; that drawing callout is not summary item 5. No complete order number is invented for marking 1306.
- Version 1307 differs from 1306 ONLY THROUGH THE ADDITIONAL INSULATING HOSE on the ignition cable and is generally supplied as a replacement. BG AND HS machines DO NOT REQUIRE the hose, but MAY INSTALL THE NEW MODULE WITH THE HOSE.
- Summary module 4137 400 1305 becomes 4137 400 1307 INCLUDING ITEM 2, hose 4137 442 0400 unchanged. Remark1 says original NO LONGER AVAILABLE FROM FACTORY. The BG 75 paragraph separately permits residual 1305 stock ONLY FOR BG 75; this is not general permission to install a non-ESL module elsewhere.
- For listed machines without a carburetor speed-control valve, the service rule requires 4137 400 1307 with ESL; BG 75 has the explicitly separate fan-load exception. Marking identification alone is not an operating test or permission to bypass speed limiting.
- Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.
Source: TI 41/1997, p. 3 · TI 41/1997, p. 4 — Section 1.2.2.1 and drawing 366TI021 KN; section 1.2.2.2; summary ignition module/item 2/remark1.
Part numbers (3)
- 4137 400 1305 — Original ignition moduleNo longer factory supplied; BG 75 residual-stock exception · Only the named TI 41/1997 configurations and conditions
- 4137 400 1307 — Replacement ESL ignition module including hose item 2General replacement · Only the named TI 41/1997 configurations and conditions
- 4137 442 0400 — Insulating hose; summary item 2Unchanged part number · Only the named TI 41/1997 configurations and conditions
Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85 / BG 72 / FC 72 / FS 48 / FS 52 / FS 56 / FS 62 / FS 66 / FS 72 / FS 74 / FS 76 / HS 72 / HS 74 / HS 76
ElastoStart replacement rope: original-number conflict retained
New 0000 195 8200 is3.0×800 mm; prose and table disagree on the original.
continuously — Continuous introduction; no numeric boundary supplied for this particular change.
- Section 3 prose prints ORIGINAL 4123 190 4000 (2.7×900 mm), replaced for some time by ELASTOSTART 0000 195 8200 (3.0×800 mm). The summary instead prints ORIGINAL 4123 195 8200. Both are confirmed on the original scan: retain the UNRESOLVED NUMBER CONFLICT, not an OCR correction, proven equivalence or two-step supersession.
- In addition to cover models, the source explicitly extends this change to BG 72, FC 72, FS 48/52/56/62/66/72/74/76 and HS 72/74/76. These are the historical configurations: not the later type 4144 FS 56 or type 4112 FS 80.
- Modification introduced CONTINUOUSLY; summary remark says ORIGINAL NO LONGER AVAILABLE FROM FACTORY. No machine-number cutoff, handle assembly replacement, knot procedure or permission to shorten either rope to an unprinted length is given. Catalog associations expose the historical note without rewriting their rope rows or choosing which conflicting original is correct.
- Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.
Source: TI 41/1997, p. 5 — Entire section 3 prose, extended model list, summary and availability remark.
Part numbers (3)
- 4123 190 4000 — Original rope number printed in prose;2.7×900 mmConflicts with summary original · Only the named TI 41/1997 configurations and conditions
- 4123 195 8200 — Original rope number printed in summaryConflicts with prose original · Only the named TI 41/1997 configurations and conditions
- 0000 195 8200 — ElastoStart rope;3.0×800 mmReplacement · Only the named TI 41/1997 configurations and conditions
Conditional replacement · HS 75 / HS 80
HS 75 / HS 80: ElastoStart and 800 mm starter rope change
New ElastoStart uses 2.7 mm rope; previous parts remain available for other models.
- Section3 replaces ElastoStart0000 190 3400 with0000 190 3403 for improved operation. The new version comes with4123 195 8200,2.7 mm x800 mm (0.106 in x31.5 in). Previous rope0000 195 8200 is3.0 mm x800 mm (0.12 in x31.5 in). The table says ElastoStart includes items2 to3; these are alternative previous/new rope rows, not both ropes supplied together.
- Introduction is IN PROGRESS with no serial cutoff. Remark1 applies to the previous ElastoStart AND previous3.0 mm rope: both remain available FOR OTHER MODELS, not an assertion of continued supply for HS75/HS80.
- Later SCS01-2012 starter sheet B (doc1760) lists the same ElastoStart0000 190 3403 but rope4137 195 8200,2.7x910 mm. Preserve that edition difference: shared grip number is not proof that the TI’s800 mm rope and later910 mm rope are interchangeable. The historical note does not overwrite the later IPL.
- Footer names last HS75/80 TI41.97; it is a chronological reference, not a delegated repair procedure or extra fitment claim.
- TI42/1999 english/USA historical evidence for HS 75 and HS 80 only. Shared 2012 catalog membership does not extend this TI to HS 85, HS 72, HS 74 or HS 76. Factory-availability remarks describe the historical issue, not current stock. No verified physical interchange, universal retrofit, torque or operating procedure is inferred.
Source: TI 42/1999, p. 4 — ElastoStart and 800 mm starter rope change.
Part numbers (4)
- 0000 190 3400 — ElastoStartItem1 previous; remains available for other models · HS 75 / HS 80; TI42 section3 ElastoStart only
- 0000 190 3403 — ElastoStartItem1 new; includes starter rope · HS 75 / HS 80; TI42 section3 ElastoStart only
- 0000 195 8200 — Starter rope 3.0 mm x 800 mm (0.12 in x 31.5 in)Item2 previous; remains available for other models · HS 75 / HS 80; TI42 section3 ElastoStart only
- 4123 195 8200 — Starter rope 2.7 mm x 800 mm (0.106 in x 31.5 in)Item3 new · HS 75 / HS 80; TI42 section3 ElastoStart only
Wrong number or missing part for the HS 75, HS 80, HS 85? Report a correction →