← HS 72, HS 74, HS 76 · HS 75, HS 80, HS 85

Stihl 4226 · Section C · 3 of 17 · 43 parts

Air filter, Fuel tank

Fits HS 75, HS 80, HS 85.

Parts diagrams →

Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314141516171819220212223242526272728293303233343536373839440414243567889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (43)

PosPart numberDescriptionQty
1 4226 129 0905 Gasket 1
2 9007 319 1130 Hexagon head screw M5x62 2
3 4137 121 1600 Spacer flange 1
4 9291 021 0121 Washer 5.3 2
5 9022 341 1050 Spline screw IS-M5x25 2
6 4226 182 7601 Tensioner 1
7 4137 123 8900 Pin 1
8 9417 003 7512 Push nut 4.0x9.6x1.8 2
9 9022 313 0680 Spline screw IS-M4x16 1
10 4137 129 0900 Gasket 1
11 4226 120 0604 Carburetor C1Q-S42C 1
12 4226 120 0602 Carburetor C1Q-S29D 1
13 4227 122 1805 Heat shield 1
14 4114 149 1205 Gasket Fitment / change note → 2
15 4137 140 2800 Filter housing 1
16 4137 141 3700 Lever 1
17 4137 141 3800 Choke shutter 1
18 9210 261 0700 Hexagon nut M5 2
19 4137 124 2800 Filter 1
20 4137 124 1500 Prefilter 1
21 4137 141 0500 Filter cover 1
22 4226 350 0401 Fuel tank 1
23 0000 989 0516 Grommet Fitment / change note → 1
24 0000 350 3503 Pickup body Fitment / change note → 1
25 4226 358 0705 Fuel hose 1
26 4226 122 3900 Elbow connector 1
27 not sold separately Hose 3.1x5.7x127 mm, R3 not available as a separate item 2
28 4226 350 0503 Filler cap 1
29 4226 350 0900 Rope 1
30 0000 353 0800 Filler cap retainer 1
32 4226 791 7200 Sleeve 1
33 4226 084 2201 Guard 1
34 9075 478 2995 NLA Pan head self-tapping screw IS-D4x12 2
35 4226 967 1504 Model plate HS 75 1
36 4226 967 1505 Model plate HS 80 1
37 4226 967 1506 Model plate HS 85 1
38 9022 341 1010 Spline screw IS-M5x18 1
39 0000 967 3693 Warning pictogram Filler cap 1
40 0000 967 3501 Instruction label 1
41 0000 967 3541 NLA Instruction label 1
42 0000 967 3795 Instruction label 1
43 not sold separately Carburetor WT-412A no longer available from factory 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2803 Hose 3.1x5.7 mm x 1 m, R3 not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · HS 75 / HS 80 / HS 85

HS 75/HS 80/HS 85: new powerhead and engine specification

25.4 cm³, 34 x 28 mm, 0.9 kW; predecessor replacement does not establish parts interchange.

  • HS 75, 80 and 85 replace HS 72, 74 and 76 for the same applications and user groups, with greater torque and power. Five-part crankshaft interconnected against twisting; four-channel transfer ports improve mixture preparation, combustion and emissions; larger cylinder cooling area.
  • Improved air-filter material and larger filter volume; twin-chamber exhaust muffler with easier spark-arresting-screen installation/removal; ElastoStart handle for softer starting. Intake noise is muffled. No one-to-one old/new part compatibility is stated.
  • Engine displacement 25.4 cm³ (1.55 cu. in), bore 34 mm (1.34 in), stroke 28 mm (1.10 in), ISO 8893 power 0.9 kW (1.2 HP). Page 3 delegates maximum and idle speeds to the carburetor table, but page 4 supplies only 2800 rpm idle and screw settings, NOT a numeric maximum speed. Do not invent a maximum or copy the BG75 fanwheel-load exception.
  • Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 17/1996, p. 1 · TI 17/1996, p. 2 · TI 17/1996, p. 3 — new powerhead and engine specification.

No additional parts-table entry added.

Service note · HS 75 / HS 80 / HS 85

HS 75/HS 80/HS 85: fuel, oil and filter specification

0.37 l tank; at least 89 octane; California 1:50 oil restriction.

  • All-position diaphragm carburetor with integral fuel pump; foam insert and felt filter. Tank capacity 0.37 l (12.5 oz. as printed). Regular branded gasoline and STIHL two-stroke engine oil; minimum 89 octane, with no octane-rating method specified here.
  • 1:50 with STIHL two-stroke engine oil 1:50; 1:25 with other branded two-stroke engine oils. California footnote permits ONLY two-stroke engine oils with a 1:50 mixing ratio. Historical source requirements, not a universal current-fuel recommendation.
  • Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 17/1996, p. 1 · TI 17/1996, p. 4 — fuel, oil and filter specification.

No additional parts-table entry added.

Service note · HS 75 / HS 80 / HS 85

HS 75/HS 80/HS 85: leak-test pressures and safety prerequisite

Crankcase pressure/vacuum 0.5 bar; inlet needle pressure 0.6 bar.

  • Crankcase leakage test: pressure +0.5 bar and vacuum magnitude 0.5 bar; the latter is not 0.5 bar absolute. Carburetor inlet needle test: pressure +0.6 bar. Do not exchange crankcase and carburetor test values.
  • The TI provides no hold duration, permitted decay or complete test setup. Starting during maintenance/repair requires national safety regulations and the Instruction Manual safety instructions. Exact Instruction Manual dependency is not supplied by this TI; the available service manual is not a substitute for that exact source.
  • Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 17/1996, p. 1 · TI 17/1996, p. 5 — leak-test pressures and safety prerequisite.

No additional parts-table entry added.

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: unchanged tank and hose-kit numbers, changed grommet

Both assemblies receive 0000 989 0516; introduction in progress.

  • Fuel tank 4226 350 0405 and fuel hose kit 4226 007 1001 retain their numbers; each now includes grommet 0000 989 0516 instead of 4221 353 9201. Only modified tank/kit versions available from factory. Original grommet remains a spare for OTHER MODELS, not proof of continued fitment here.
  • Introduction is IN PROGRESS; no machine-number threshold is printed for this change.
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 5 — HS 72–85: unchanged tank and hose-kit numbers, changed grommet.

Part numbers (4)
  • 4226 350 0405 — Fuel tank, unchanged assembly numberHistorical listed item · TI04/1997 exact named HS models and version restrictions
  • 4226 007 1001 — Fuel hose kit, unchanged assembly numberHistorical listed item · TI04/1997 exact named HS models and version restrictions
  • 4221 353 9201 — Original grommetoriginal version · TI04/1997 exact named HS models and version restrictions
  • 0000 989 0516 — New grommetnew version · TI04/1997 exact named HS models and version restrictions

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: debris prefilter standardized at X 34 573 587

4226 141 0300 changes to 4226 141 0301.

X 34 573 587 — Prefilter change only.

  • Debris filter 4226 141 0300 → 4226 141 0301 standardizes inventories. Original no longer available from factory. Figure 366TI016 KN shows the filter form; no unprinted dimensions or other-model compatibility inferred.
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 5 — HS 72–85: debris prefilter standardized at X 34 573 587.

Part numbers (2)
  • 4226 141 0300 — Original debris filteroriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 141 0301 — New debris filternew version · TI04/1997 exact named HS models and version restrictions

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: cap filter added without changing cap number

Filter 0000 358 1810 introduced at X 32 106 939.

X 32 106 939 — Item 5 cap filter only.

  • Fuel filler cap 4226 350 0501 retains its number and now includes filter 0000 358 1810 (table item 5). Original filter column is a dash: new included component, not an old filter number. Only modified cap supplied from factory.
  • Figure 366TI017 KN retains the cap-component order as illustrated; unnumbered rings/internals are not assigned invented part numbers. Cap filter cutoff is NOT the pick-up-body cutoff.
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 6 — HS 72–85: cap filter added without changing cap number.

Part numbers (2)
  • 4226 350 0501 — Fuel filler cap, unchanged numberHistorical listed item · TI04/1997 exact named HS models and version restrictions
  • 0000 358 1810 — New included filter, item 5Historical listed item · TI04/1997 exact named HS models and version restrictions

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: pick-up body and unchanged 4226 007 1002 assembly

Pick-up-body cutoff X 36 287 313 differs from cap filter.

X 36 287 313 — Item 2 pick-up body only, not gasket/kit-wide.

  • Table labels 4226 007 1002 as “Fuel filler cap assembly”, including item 2 PICK-UP BODY and item 3 CYLINDER/SPACER-FLANGE GASKET. This unusual source label/content grouping is preserved, not corrected into a cap-only kit or proof the gasket fits inside the cap. Assembly number stays unchanged; only modified version supplied.
  • Pick-up body 4226 350 3500 → 0000 350 3503. Figure 366TI015 KN labels 1 old, 2 new. Old pick-up body supplied only while factory stocks last. X 36 287 313 applies to item 2, not the gasket or whole assembly. Other changes are described as in progress.
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 6 — HS 72–85: pick-up body and unchanged 4226 007 1002 assembly.

Part numbers (5)
  • 4226 007 1002 — Assembly retaining the source label and unchanged numberHistorical listed item · TI04/1997 exact named HS models and version restrictions
  • 4226 350 3500 — Original pick-up bodyoriginal version · TI04/1997 exact named HS models and version restrictions
  • 0000 350 3503 — New pick-up bodynew version · TI04/1997 exact named HS models and version restrictions
  • 4226 129 0901 — Original included cylinder/spacer-flange gasketoriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 129 0902 — New included cylinder/spacer-flange gasketnew version · TI04/1997 exact named HS models and version restrictions

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: cylinder-to-spacer-flange gasket replacement

4226 129 0901 → 4226 129 0902; no independent serial cutoff.

  • The prose locates this gasket BETWEEN THE CYLINDER AND SPACER FLANGE. Original 4226 129 0901 replaced by 4226 129 0902; original no longer available from factory (remark 3). Introduction in progress, with no gasket-specific serial.
  • The table includes this gasket in unchanged assembly 4226 007 1002 labeled “Fuel filler cap assembly”; retain that label/content anomaly separately from the explicit cylinder location. Do not apply cap-filter or pick-up-body serials to the gasket.
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 6 — HS 72–85: cylinder-to-spacer-flange gasket replacement.

Part numbers (3)
  • 4226 129 0901 — Original cylinder/spacer-flange gasketoriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 129 0902 — New cylinder/spacer-flange gasketnew version · TI04/1997 exact named HS models and version restrictions
  • 4226 007 1002 — Table assembly with unusual fuel-filler-cap labelHistorical listed item · TI04/1997 exact named HS models and version restrictions

Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85

Heat-shield sealing: one 4114 149 1205 gasket on each side

Fit missing gaskets on original-version machines; total quantity two.

  • Section 4 says 4114 149 1205 (1) has for some time been fitted ON BOTH SIDES OF HEAT SHIELD (2) to improve sealing. Drawing366TI023 GM places one gasket between carburetor and shield and another between shield and the air-filter side. The summary explicitly says GASKET (2x).
  • Service note: MISSING GASKETS MUST BE FITTED IN MODELS WITH THE ORIGINAL VERSION. Continuous introduction; no numeric cutoff. Do not stack both on one side, interpret2x as two pairs, invent a shield number or transfer this instruction to unlisted successor models.
  • The footer lists last TIs BG 75 TI 42.96 (TI 27.97 USA only), FC/FS/HL/HT TI 37.97 and HS TI 04.97. These are bibliographic history, not delegated procedures required to apply this gasket note; no missing-source closure claim is created from the footer alone.
  • Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.

Source: TI 41/1997, p. 6 — Complete section 4, drawing 366TI023 GM, quantity 2 summary, service note and footer.

Part numbers (1)
  • 4114 149 1205 — Heat-shield gasket; drawing 1, quantity 2Fit missing gaskets · Only the named TI 41/1997 configurations and conditions

Wrong number or missing part for the HS 75, HS 80, HS 85? Report a correction →