Stihl 4226 · Section N · 13 of 17 · 31 parts
Control handle HS 80
Fits HS 80.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (31)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 2 | 4226 160 2501 | Brake cable | 1 |
| 3 | 4226 790 3300 | AV carrier | 1 |
| 4 | 4226 791 7200 | Sleeve | 2 |
| 5 | 4226 791 2805 | Annular buffer | 2 |
| 6 | 4226 791 9700 | Washer | 2 |
| 7 | 9022 341 1010 | Spline screw IS-M5x18 | 2 |
| 8 | 4226 791 7300 | Plug | 2 |
| 9 | 4226 791 0606 | Handle molding, left | 1 |
| 10 | 4226 162 5000 | Lever | 1 |
| 11 | 4226 182 3700 | Connector tag | 2 |
| 12 | 4226 182 1700 | Slide control | 1 |
| 13 | 4226 182 3600 | Contact spring | 1 |
| 14 | 9093 021 1760 | Self-tapping screw 2.9x9.5 | 1 |
| 15 | 0000 998 0806 | Torsion spring | 1 |
| 16 | 4226 440 1105 | Short circuit wire 370 mm / 14.5'' | 2 |
| 19 | 4226 182 1000 | Throttle trigger | 1 |
| 20 | 0000 998 1003 | Torsion spring | 1 |
| 21 | 4226 182 0800 | Lockout lever | 1 |
| 22 | 4226 180 1101 | Throttle cable | 1 |
| 23 | 4226 792 7100 | Blocking lever | 1 |
| 24 | 0000 997 0724 | Compression spring | 1 |
| 25 | 4226 792 7300 | Safety slide | 1 |
| 26 | 9645 945 3902 | O-ring 44x3 | 1 |
| 27 | 4226 791 0602 | Handle molding, right | 1 |
| 28 | 9074 478 3075 | Pan head self-tapping screw IS-P4x19 | 4 |
| 29 | 4226 792 9102 | Hand guard | 1 |
| 30 | 4226 791 1700 | Handlebar | 1 |
| 31 | 4226 792 9300 | Rubber buffer | 2 |
| 32 | 9074 478 4135 | Pan head self-tapping screw IS-P5x20 | 1 |
| 33 | 9022 313 0680 | Spline screw IS-M4x16 | 4 |
| 34 | 0000 967 3700 | Warning pictogram HS | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HS 75 / HS 80
HS 75/HS 80: blade-guide and handle torques
Three model-restricted values; do not substitute the HS85 screws or torques.
- HS75 and HS80 ONLY, Nm: IS-M5x20 blade guide/gear housing 9.5; IS-M5x18 rubber buffer/handle moulding 3.5; plastoform IS-P4x19 handle moulding 2.0.
- HS85 has separately listed screw lengths, mounting components and handle torque. These HS75/80 values do not apply merely because the common IPL family metadata includes HS85.
- Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 17/1996, p. 1 · TI 17/1996, p. 7 — HS75/80 blade-guide and handle torques.
No additional parts-table entry added.
Wrong number or missing part for the HS 80? Report a correction →