Stihl 4226 · Section P · 15 of 17 · 23 parts
Control handle HS 85
Fits HS 85.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (23)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4140 790 0301 | Handle | 1 |
| 2 | 9074 478 3025 | Pan head self-tapping screw IS-P4x16 | 3 |
| 3 | 4128 182 1700 | Slide control | 1 |
| 4 | 4128 182 4201 | Detent spring | 1 |
| 5 | 4128 182 6200 | Collar screw | 1 |
| 6 | 4128 182 4502 | Torsion spring | 1 |
| 7 | 4128 182 4504 | Torsion spring | 1 |
| 8 | 4128 182 4500 | Torsion spring | 1 |
| 9 | 4128 182 1000 | Throttle trigger | 1 |
| 10 | 4128 182 4501 | Torsion spring | 1 |
| 11 | 4128 182 0800 | Lockout lever | 1 |
| 12 | 9214 320 0700 | Lock nut M5 | 1 |
| 13 | 9022 346 1070 | Spline screw IS-M5x30 | 1 |
| 14 | 9291 021 0120 | Washer 5.3 | 1 |
| 15 | 4226 182 3200 | Throttle cable | 1 |
| 16 | 0751 030 8470 | Grommet no longer available from factory | 2 |
| 17 | 0751 030 8958 | Terminal socket 4.8-1 no longer available from factory | 2 |
| 18 | not sold separately | Hose 295 mm / 11 5/8'' not available as a separate item | 1 |
| 19 | 4140 798 1400 | Shell | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4226 790 1303 | Control handle | 1 |
| — | 4140 790 1304 | Control handle | 1 |
| — | 4226 180 1107 | Throttle cable | 1 |
| — | 4203 711 7201 | Hose 960 mm / 37 13/16'' not illustrated | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HS 85
HS 85: blade-guide and handle torques
Three HS85-only values; model-specific fasteners and mounting locations retained.
- HS85 ONLY, Nm: IS-M5x25 blade guide/gear housing 9.5; IS-M5x16 rubber buffer/gear housing 5.5; IS-M5x30 handle halves 2.5. Do not transfer HS75/80 buffer or handle values.
- Current early cutter sheet shows IS-M5x20 while this TI specifies IS-M5x25 for the blade guide; preserve the configuration/fastener difference. Later cutter-sheet serial boundaries are not supplied by this TI and are not inferred here.
- Historical HS 75, HS 80 and HS 85 type 4226 evidence, restricted to the models named in this note. Replacement of HS 72/74/76 is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 17/1996, p. 1 · TI 17/1996, p. 7 — HS85 blade-guide and handle torques.
No additional parts-table entry added.
Wrong number or missing part for the HS 85? Report a correction →