← HS 72, HS 74, HS 76 · HS 75, HS 80, HS 85

Stihl 4226 · Section R · 17 of 17 · 20 parts

Handle HS 85, Tools

Fits HS 85.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922344566789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (20)

PosPart numberDescriptionQty
1 4226 790 0500 Handle 1
2 4226 791 0350 Handle 1
3 9074 478 4135 Pan head self-tapping screw IS-P5x20 1
4 0000 967 3700 Warning pictogram HS 1
5 4226 791 7200 Sleeve 1
6 9220 263 0702 Hexagon nut M5 2
7 9022 341 1050 Spline screw IS-M5x25 1
8 9307 021 0120 Washer 5.3 2
9 9216 261 0700 Hexagon nut M5 1
10 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 1
11 4226 792 2701 Cover 1
12 9022 313 0680 Spline screw IS-M4x16 4
13 not sold separately Handle no longer available from factory 1
14 9074 478 4135 Pan head self-tapping screw IS-P5x20 2
15 9075 478 4712 Pan head self-tapping screw IS-D6x28 1
16 4226 648 7700 Cover 1
17 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 1
18 4128 890 3400 Combination wrench Fitment / change note → 1
19 0000 890 2300 NLA Screwdriver 1
Not numbered on the diagram — assemblies, kits and options
— 4226 790 0550 Handle 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 75 / FS 80 / FS 85 / HS 75 / HS 80 / HS 85

FS and HS: combination wrench gains size13 and a longer size19 sleeve

4128 890 3400 replaces 4119 890 3400 in supplied equipment.

continuously — Continuous introduction; no numeric boundary supplied for this particular change.

  • Section 2 is limited to FS AND HS models named on the cover. Standardization changes the supplied combination wrench from 4119 890 3400 (1) to 4128 890 3400 (2). It adds a SIZE 13 HEX KEY (3); the SIZE 19 SLEEVE (4) is APPROXIMATELY10 mm (3/8 inch) LONGER.
  • Drawing366TI022 KN labels original sleeve40 mm (1.57 inch) and replacement50 mm (2 inch). These are the drawn sleeve spans, not overall wrench length. Modification continuous; ORIGINAL REMAINS AVAILABLE. No recall or replacement requirement for existing tools is stated.
  • Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.

Source: TI 41/1997, p. 5 — Entire section 2, drawing 366TI022 KN, summary and remark.

Part numbers (2)
  • 4119 890 3400 — Original combination wrench; drawing 1Remains available · Only the named TI 41/1997 configurations and conditions
  • 4128 890 3400 — New combination wrench; drawing 2New supplied version · Only the named TI 41/1997 configurations and conditions

Wrong number or missing part for the HS 85? Report a correction →