← BG 75

Stihl 4227 · Section E · 5 of 8 · 32 parts

Carburetor C1Q-S30C

Fits BG 75.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516171819220212223242526272829330456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (32)

PosPart numberDescriptionQty
1 4227 120 7101 Throttle shaft with lever 1
2 1123 122 3000 Spring 1
3 4227 121 3300 Throttle shutter 1
4 1125 122 7403 Round head screw 1
5 1120 122 9000 E-clip 1
6 4227 123 7301 Lever 1
7 9079 319 0280 Flat head screw M3x3.5 1
8 1129 121 4800 Pump diaphragm 1
9 1123 129 0905 Gasket 1
10 1123 121 0800 End cover 1
11 1120 122 7800 Oval head screw 1
12 4116 121 5100 Inlet needle 1
13 1123 122 3001 Spring 1
14 1125 121 5000 Inlet control lever 1
15 1120 121 9200 Spindle 1
16 1120 122 6600 Collar screw 1
17 4129 129 0902 Gasket Fitment / change note → 1
18 4129 121 4700 Metering diaphragm Fitment / change note → 1
19 4227 120 2200 Flange Fitment / change note → 1
20 1128 122 7100 Screw Fitment / change note → 2
21 4227 122 6800 Low speed adjustment screw 1
22 4226 122 7100 Screw Fitment / change note → 2
23 1120 122 3005 Spring 1
24 1123 121 7800 Strainer 1
25 4227 121 5402 Valve jet 1
26 4226 121 0700 Cup plug 1
27 4226 121 0800 End cover Fitment / change note → 1
28 4226 121 2700 Cap 1
29 1123 122 6200 Idle speed adjustment screw 1
30 1125 122 4200 Clamp 1
Not numbered on the diagram — assemblies, kits and options
— 4227 120 0602 Carburetor C1Q-S30C Fitment / change note → 1
— 4227 007 1060 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · BG 75

BG 75: flange kit without whole-carburetor changeover

BG 75 retains its two-screw replacement carburetor; use its model-specific four-screw flange kit.

  • The two-screw end cover can distort the primer flange and metering diaphragm. The revised end cover and flange use four screws. On previous carburetors, exchange flange and cover together with the two additional longer screws; do not change only one component.
  • Unresolved screw-number conflict: page 3 prose specifies 4226 121 7100; page 4 summary item 9 specifies 4226 122 7100, quantity increased from two to four. Both original scans agree with their respective text. Neither number is silently corrected or certified as the right screw.
  • Page 3 drawing identifies A screws, B/B1 old/new end cover, C/C1 old/new flange, D metering diaphragm and E gasket. Kit comprises A, B1, C1, D, E. Page 4 instructs finger-tight insertion, then alternate diagonal tightening. No torque is stated; separately supplied kit installation instructions are referenced but were not located in the retained STIHL service documentation document index/resources or supplemental manual PDFs. Later workshop flange sections are not the exact kit instructions; this remains a documented source gap.
  • Common unchanged diaphragm 4129 121 4700 and gasket 4129 129 0902 remain listed. Previous two-screw item 8 is 1128 122 7100; item 9 is 4226 122 7100. Old end cover 4226 121 0800 remains a spare for other models; the new end cover and flange are not separate supply items. Summary asterisks/dashes are not new order numbers.
  • BG 75 replacement carburetor C1Q-S30, 4227 120 0602, was not changed over to the four-screw flange. A four-screw spare flange kit 4227 120 2250 is available; do not substitute the general 4140 kit or C1Q-S56 carburetor merely because other models changed.
  • Summary item 10 includes 4, 6–9 and 12. Kit item 11 contains 4, 6, 7, 9, 12; flange 4227 120 2200 is replaced by this kit. Support 4227 700 8450 keeps its number and includes kit 11. Remark 5 retains unmodified carburetor/support supply until stocks exhausted; same part number does not identify modification state.
  • The retained IPL names C1Q-S30C while this TI names C1Q-S30. The link is model/family navigation, not evidence that the suffix configurations are identical.
  • Only explicitly named models and configurations are covered. Shared IPL pages do not extend these assertions to unnamed R/RX or other variants. Availability statements describe 2001 factory support, not present stock. The printed cover places FH/HL under 4230, HT under 4138 and KW under 4602; retained exact-model engine sheets use 4137 as navigation, not proof of series equivalence.

Source: TI 16/2001, p. 3 · TI 16/2001, p. 4 · TI 16/2001, p. 5 — Sections 3.1, 3.1.2, 3.1.4–3.1.5: BG 75 exception and all summary inclusions.

Part numbers (10)
  • 4227 120 0602 — Carburetor C1Q-S30Two-screw replacement not changed over · BG 75; named configuration only
  • 4227 120 2250 — BG 75 flange kitFour-screw spare conversion · BG 75; named configuration only
  • 4227 120 2200 — Previous BG 75 flangeUse kit · BG 75; named configuration only
  • 4227 700 8450 — Support including kit 11Same number; unmodified stocks exhausted · BG 75; named configuration only
  • 4226 121 0800 — Previous end coverRemains for other models; new cover not separate · BG 75; named configuration only
  • 4129 121 4700 — Metering diaphragmUnchanged · BG 75; named configuration only
  • 4129 129 0902 — GasketUnchanged · BG 75; named configuration only
  • 1128 122 7100 — Previous screw, item 8Two in old arrangement · BG 75; named configuration only
  • 4226 122 7100 — Screw, summary item 9Four in new arrangement; conflicts with prose · BG 75; named configuration only
  • 4226 121 7100 — Longer screw as printed in proseUnresolved conflict with summary · BG 75; named configuration only

Wrong number or missing part for the BG 75? Report a correction →