Stihl 4227 · Section F · 6 of 8 · 34 parts
Carburetor WT-413
Fits BG 75.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (34)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4133 121 5400 | Valve jet | 1 |
| 2 | 4117 122 9402 | Plug | 1 |
| 3 | 1110 121 5100 | Inlet needle | 1 |
| 4 | 1120 122 3001 | Spring | 1 |
| 5 | 1113 121 5000 | Inlet control lever | 1 |
| 6 | 1113 121 9200 | Spindle | 1 |
| 7 | 1114 122 7400 | Round head screw | 1 |
| 8 | 4133 129 0901 | Gasket | 1 |
| 9 | 1113 121 4705 | Metering diaphragm | 1 |
| 10 | 4133 120 2201 | Flange | 1 |
| 11 | 4133 121 5200 | Valve | 1 |
| 12 | 4133 121 2700 | Cap | 1 |
| 13 | 4133 121 0801 | End cover | 1 |
| 14 | 4133 122 7400 | Round head screw | 4 |
| 15 | 1114 121 7800 | Strainer | 1 |
| 16 | 1120 121 4805 | Pump diaphragm | 1 |
| 17 | 1120 129 0905 | Gasket | 1 |
| 18 | 4117 121 0803 | End cover | 1 |
| 19 | 1114 122 7100 | Screw | 1 |
| 20 | 4117 122 3006 | Spring | 1 |
| 21 | 4117 122 6200 | Idle speed adjustment screw | 1 |
| 22 | 4119 122 3200 | Torsion spring | 1 |
| 23 | 1117 122 9000 | E-clip | 1 |
| 24 | 4227 120 7100 | Throttle shaft with lever | 1 |
| 25 | 4227 123 7300 | Lever | 1 |
| 26 | 4117 122 3007 | Spring | 1 |
| 27 | 4211 122 6700 | High speed adjustment screw | 1 |
| 28 | 4119 122 6801 | Low speed adjustment screw | 1 |
| 29 | 1115 122 3002 | Spring | 1 |
| 30 | 4117 121 3300 | Throttle shutter | 1 |
| 31 | 1110 122 7400 | Round head screw | 2 |
| 32 | 4133 120 8600 | Non-return valve | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | not sold separately | Carburetor WT-413 no longer available from factory | 1 |
| — | 4133 007 1060 | Set of carburetor parts Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · BG 75
BG 75: WT 413 settings and separate parts kit
Walbro H/L standard one turn, 2800 rpm idle; WT 253 adjustment cross-reference.
- Walbro WT 413: A in drawing 326TI002 is the valve jet. L=OPEN ONE FULL TURN and H=OPEN ONE FULL TURN are standard settings; idle 2800 rpm. Kit 4133 007 1060 belongs to WT 413, not the Zama version. No carburetor assembly number is supplied by this TI.
- Page 3 footnote 2 says a maximum engine-speed value is technically unnecessary because the fanwheel constantly takes power; it supplies NO numeric maximum. This is not permission to run without fanwheel load.
- Page 6 delegates WT 413 adjustment to the method for WT 253. The Zama symptom-specific quarter/eighth-turn changes must not be silently transferred to Walbro. Local combined HS75/80/85/BG 75 service manual sections 9.2.3–9.2.4 are available, but do not name WT 253; exact predecessor procedure provenance remains unconfirmed. See batch 141 dependency receipt.
- Current IPL labels WT 413 without a numbered complete assembly; do not infer a replacement carburetor number from the shared air-filter sheet.
- Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 16/1996, p. 1 · TI 16/1996, p. 3 · TI 16/1996, p. 5 · TI 16/1996, p. 6 — WT413 settings and separate parts kit.
Part numbers (1)
- 4133 007 1060 — Carburetor parts kitTI16/1996 listed item · WT 413 only
Service note · BG 75
BG 75: crankcase and carburetor test pressures
Crankcase ±0.5 bar; inlet needle+0.6 bar; safety prerequisite retained.
- Crankcase leakage test: OVERPRESSURE 0.5 bar and UNDERPRESSURE 0.5 bar. Carburetor inlet needle: OVERPRESSURE 0.6 bar. Vacuum magnitude is not0.5 bar absolute; inlet needle value must not be assigned to crankcase.
- No holding time, permitted decay or complete isolation/test setup is supplied in this TI. If started during repair/maintenance, follow country-of-use safety regulations and Owner’s Manual safety instructions. No unattended operating procedure or hardware test is implied. Exact Owner’s Manual dependency is not supplied by this TI.
- Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 16/1996, p. 1 · TI 16/1996, p. 5 — crankcase and carburetor test pressures.
No additional parts-table entry added.
Wrong number or missing part for the BG 75? Report a correction →