← HS 45

Stihl 4228 · Section A · 1 of 10 · 19 parts

Crankcase, Cylinder

Fits HS 45.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121213131415161722334456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (19)

PosPart numberDescriptionQty
1 4140 021 0300 Crankcase 1
2 9639 003 1230 Oil seal 12x22x7 2
3 9503 003 0246 Grooved ball bearing 6201 2
4 4140 036 0300 Washer 2
5 4228 030 0402 Crankshaft Fitment / change note → 1
6 4228 030 0400 Crankshaft Fitment / change note → 1
7 4140 029 2300 Cylinder gasket 1
8 4140 021 2500 Engine pan 1
9 4140 020 1202 Cylinder with piston Ø 34 mm 1
10 4140 020 1200 NLA Cylinder with piston Ø 34 mm → replaced by 4140 020 1202 TI 23/2003 1
11 4140 030 2000 Piston Ø 34 mm 1
12 4137 034 3000 Piston ring Ø 34x1.5 mm 2
13 9463 650 0807 Snap ring 8x0.7 2
14 4137 034 1500 Piston pin 8x5x22 1
15 9075 478 4268 Pan head self-tapping screw IS-D5x60 4
16 1110 400 7005 Spark plug Bosch WSR 6 F 1
16 0000 400 7000 Spark plug NGK BPMR7A 1
17 0783 830 2000 Tube of sealant Dirko HT red option 1
Not numbered on the diagram — assemblies, kits and options
— 4228 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · HS 45

HS 45 ignition and crankshaft: new-carburetor restriction

Machines with C1Q-S67 require the new ignition module and re-keyed crankshaft when repaired.

  • Ignition module 4140 400 1302 replaces 4140 400 1300 together with crankshaft 4228 030 0402 replacing 4228 030 0400. The crankshaft flywheel key slot changes position; the drawing compares the old and new slots but specifies no numerical timing angle.
  • For repairs to HS 45 machines with carburetor 4228 120 0603, only the new versions of these parts may be used. The package optimizes timing and cutoff speed range, but gives no cutoff RPM or permission to mix generations.
  • Previous module and crankshaft remain available for older machines. Introduction is in progress with no serial stated. The later retained IPL module 4140 400 1308 does not silently supersede the TI-specific 1302 assertion; this note does not establish that later relationship.
  • HS 45 only. Factory availability describes the 2001 bulletin, not present stock. No physical interchange or running adjustment was tested.

Source: TI 26/2001, p. 6 · TI 26/2001, p. 7 — Section 4.4, key-slot drawing and 4.5 rows 15–16.

Part numbers (5)
  • 4140 400 1300 — Ignition modulePrevious · HS 45; configuration restrictions in this note
  • 4140 400 1302 — Ignition moduleRequired new version for C1Q-S67 · HS 45; configuration restrictions in this note
  • 4228 030 0400 — CrankshaftPrevious key-slot position · HS 45; configuration restrictions in this note
  • 4228 030 0402 — CrankshaftNew key-slot position · HS 45; configuration restrictions in this note
  • 4228 120 0603 — Carburetor C1Q-S67Restriction identifier · HS 45; configuration restrictions in this note

Wrong number or missing part for the HS 45? Report a correction →