← HS 45

Stihl 4228 · Section B · 2 of 10 · 16 parts

Ignition system, Muffler

Fits HS 45.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141523456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (16)

PosPart numberDescriptionQty
1 4140 400 1200 Flywheel 1
2 0000 955 0802 Collar nut M8x1 1
3 4140 400 1308 Ignition module 1
4 4140 400 1300 Ignition module Fitment / change note → 1
5 4140 431 2100 Connector tag 1
6 9075 478 3023 Pan head self-tapping screw IS-D4x22 2
7 4228 084 1100 Spiral housing 1
8 9075 478 4159 Pan head self-tapping screw IS-D5x24 3
9 4228 140 0600 Muffler 1
10 4228 140 0601 Muffler 1
11 4128 140 6900 NLA Stub with screen 1
12 4140 149 0602 Muffler gasket 1
13 9075 478 4268 Pan head self-tapping screw IS-D5x60 2
14 4228 160 2000 Clutch 1
15 4228 162 7903 Tension spring 2
Not numbered on the diagram — assemblies, kits and options
— 4228 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · HS 45

HS 45 ignition and crankshaft: new-carburetor restriction

Machines with C1Q-S67 require the new ignition module and re-keyed crankshaft when repaired.

  • Ignition module 4140 400 1302 replaces 4140 400 1300 together with crankshaft 4228 030 0402 replacing 4228 030 0400. The crankshaft flywheel key slot changes position; the drawing compares the old and new slots but specifies no numerical timing angle.
  • For repairs to HS 45 machines with carburetor 4228 120 0603, only the new versions of these parts may be used. The package optimizes timing and cutoff speed range, but gives no cutoff RPM or permission to mix generations.
  • Previous module and crankshaft remain available for older machines. Introduction is in progress with no serial stated. The later retained IPL module 4140 400 1308 does not silently supersede the TI-specific 1302 assertion; this note does not establish that later relationship.
  • HS 45 only. Factory availability describes the 2001 bulletin, not present stock. No physical interchange or running adjustment was tested.

Source: TI 26/2001, p. 6 · TI 26/2001, p. 7 — Section 4.4, key-slot drawing and 4.5 rows 15–16.

Part numbers (5)
  • 4140 400 1300 — Ignition modulePrevious · HS 45; configuration restrictions in this note
  • 4140 400 1302 — Ignition moduleRequired new version for C1Q-S67 · HS 45; configuration restrictions in this note
  • 4228 030 0400 — CrankshaftPrevious key-slot position · HS 45; configuration restrictions in this note
  • 4228 030 0402 — CrankshaftNew key-slot position · HS 45; configuration restrictions in this note
  • 4228 120 0603 — Carburetor C1Q-S67Restriction identifier · HS 45; configuration restrictions in this note

Wrong number or missing part for the HS 45? Report a correction →