Stihl 4229 · Section A · 1 of 24 · 18 parts
Crankcase, Cylinder
Fits BG 45, BG 46, BG 55, BG 65, BG 85.
Historical fitment & changes (13) — includes parts and conditions not shown on this drawing.
Parts (18)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4140 021 0300 | Crankcase | 1 |
| 2 | 9639 003 1230 | Oil seal 12x22x7 | 2 |
| 3 | 9503 003 0246 | Grooved ball bearing 6201 | 2 |
| 4 | 4140 036 0300 | Washer | 2 |
| 5 | 4229 030 0400 | Crankshaft | 1 |
| 6 | 4140 029 2300 | Cylinder gasket | 1 |
| 7 | 4140 021 2500 | Engine pan | 1 |
| 8 | 4140 020 1202 | Cylinder with piston Ø 34 mm | 1 |
| 9 | 4140 020 1200 NLA | Cylinder with piston Ø 34 mm → replaced by 4140 020 1202 TI 23/2003 | 1 |
| 10 | 4140 030 2000 | Piston Ø 34 mm | 1 |
| 11 | 4137 034 3000 | Piston ring Ø 34x1.5 mm | 2 |
| 12 | 9463 650 0807 | Snap ring 8x0.7 | 2 |
| 13 | 4137 034 1500 | Piston pin 8x5x22 | 1 |
| 14 | 9075 478 4268 | Pan head self-tapping screw IS-D5x60 | 4 |
| 15 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 15 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 16 | 0783 830 2000 | Tube of sealant Dirko HT red option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4229 007 1050 | Set of gaskets Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: original design and equipment distinctions
1999 design: four-port cylinder, dual-chamber muffler and purge primer; working-RPM setting lever only on BG 85/SH 85.
- BG 55/65/85 are handheld blowers. SH 55/85 are introduced as a new STIHL vacuum-shredder category, with a standard vacuum attachment and blower tube and a shredder blade mounted on the fanwheel. The engine is enclosed in a compact housing. These descriptions do not identify a numbered vacuum kit or prove that every illustrated component fits every named model.
- The manufacturer describes ergonomic controls and a favorable power-to-weight ratio for easy handling and less fatigue, with typical applications in gardens and yards, sports facilities, grounds and parks. These are historical product descriptions, not measured ergonomic results or unrestricted material-use instructions. The page 1 photograph has no component callouts, measurements or serial applicability.
- The composite crankshaft forms a torsionally rigid assembly with both ends supported in bearings. The cylinder uses four-port technology, described as improving mixture control, combustion and emissions, and has a large cooling area. No crankshaft, bearing or cylinder part number, port dimension or retrofit instruction is supplied here.
- Air-filter features are improved filter material and a large surface area; the exhaust muffler has two chambers. The easy-start system includes a purge primer. ElastoStart is standard on BG 85 and SH 85 and otherwise optional; its accessory numbers and historical rope-length discrepancy are retained in the separate starter note.
- The controls include a multifunction handle. The setting lever for preselecting working RPM is specified only for BG 85 and SH 85. It is not a universal feature of BG 55/65 or SH 55 and does not establish a speed-limiting ignition system. The balanced-idle carburetor and its distinct handbook dependency are covered separately.
- This is the 1999 English/USA introduction for BG 55, BG 65, BG 85, SH 55 and SH 85, series 4229. It does not cover BG 45/46, BR 45 C, an unlisted SH 65 or every later variant. Shared catalog headings do not widen these specifications. No serial threshold, physical interchange test or present production configuration is established.
Source: TI 29/1999, p. 1 · TI 29/1999, p. 2 — Introduction and section 1 technical description, except carburetor handbook detail.
No additional parts-table entry added.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: 1999 power, airflow and weight specifications
Preserve model-specific output and airflow, blank BG vacuum figures, and the printed 30 mm / 1.10 in stroke discrepancy.
- Both engine columns specify displacement 27.2 cm³ (1.66 cu.in), bore 34 mm (1.34 in) and stroke 30 mm (1.10 in). The printed stroke pair is inconsistent: 30 mm is approximately 1.18 in, not 1.10 in. Both source values are retained; neither is silently corrected, and no machining dimension or alternative stroke is inferred.
- Power to ISO 8893: BG 55, BG 65 and SH 55 are 0.7 kW (0.95 HP) at 7,000 rpm; BG 85 and SH 85 are 0.8 kW (1.1 HP) at 7,000 rpm. The rated-power speed is not an idle target, maximum permissible speed or proof of a limiter. Page 3 redirects idle speed to section 2.1.2.
- Airflow table (airflow CFM; vacuum-mode airflow CFM; air velocity MPH): BG 55 — 430; blank; 141. BG 65 — 430; blank; 174. BG 85 — 459; blank; 183. SH 55 — 430; 353; 141. SH 85 — 459; 368; 183. Blank BG vacuum cells are unspecified, not zero and not proof that a vacuum accessory is unsupported. The table does not specify a nozzle configuration or measurement method, so these figures are not assigned to a particular nozzle part.
- Weight: BG 55 3.9 kg (8.6 lb); BG 65 4.0 kg (8.8 lb); BG 85 4.0 kg (8.8 lb); SH 55 4.8 kg (10.6 lb); SH 85 4.9 kg (10.8 lb). The source does not qualify these as dry, fueled or with a particular attachment. No unstated weight basis is added.
- Both engine columns specify a single-pawl rewind starter and 3 mm (0.12 in) diameter, 800 mm (31.5 in) rope. The separate starter-accessory note preserves the later 1060 mm catalog difference and distinguishes the engine specification from packaged accessory length. None of these general specifications changes the original catalog rows.
- This is the 1999 English/USA introduction for BG 55, BG 65, BG 85, SH 55 and SH 85, series 4229. It does not cover BG 45/46, BR 45 C, an unlisted SH 65 or every later variant. Shared catalog headings do not widen these specifications. No serial threshold, physical interchange test or present production configuration is established.
Source: TI 29/1999, p. 3 · TI 29/1999, p. 4 — Sections 2.1.1 engine/airflow and 2.2 weight.
No additional parts-table entry added.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: electronic magneto and suppressed spark plugs
TI29 names Bosch WSR 6F, NGK BPMR 7 A or Champion RCJ 6Y; no plug gap or ignition-module part number is given.
- Ignition module: electronic magneto ignition. Suppressed spark plug choices printed in section 2.1.3 are Bosch WSR 6F, NGK BPMR 7 A or Champion RCJ 6Y. The source supplies no plug gap, tightening torque, ignition timing, module air gap, maximum RPM or numbered module identity; none is inferred.
- Later SCS 01-2012 BG and SH crankcase/cylinder sheets list NGK BPMR7A as 0000 400 7000 and Bosch WSR 6 F as 1110 400 7005, both at position 15. These catalog identities are comparison evidence, not part numbers printed in TI29. No numbered Champion replacement is established, and absence of a Champion row does not erase the historical third plug choice. Catalog rows remain unchanged.
- This is the 1999 English/USA introduction for BG 55, BG 65, BG 85, SH 55 and SH 85, series 4229. It does not cover BG 45/46, BR 45 C, an unlisted SH 65 or every later variant. Shared catalog headings do not widen these specifications. No serial threshold, physical interchange test or present production configuration is established.
Source: TI 29/1999, p. 3 — Section 2.1.3 ignition system.
No additional parts-table entry added.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: engine gasket set and crankshaft cleaning aid
TI29 lists engine gasket set 4229 007 1050 and a restricted solvent-based degreaser; the 4140 tool table is separately reviewed.
- Section 4.2 lists set of gaskets 4229 007 1050 for the engine. It gives no individual gasket contents, replacement sequence or all-model sealing procedure. Later BG and SH crankcase/cylinder sheets retain this set as an unpositioned row, quantity one. That catalog quantity is comparison evidence; the TI table itself does not specify a quantity or kit contents.
- The unnumbered cleaning aid is a standard commercial solvent-based degreaser containing no chlorinated or hydrogenated hydrocarbons, for cleaning the crankshaft stub. Preserve the printed word hydrogenated; it is not silently changed to halogenated. The source names no brand, product number, dilution or substitute. This is not an unrestricted solvent recommendation, a rinsing procedure for the fuel system or approval for all plastics and seals.
- Source wording conflict: the August 1999 powerhead manual, section 10 (printed page 17 / PDF page 18), specifies neither chlorinated nor halogenated hydrocarbons for the same crankshaft-stub cleaning application, while TI29 prints hydrogenated. Both readings are retained without silently harmonizing them or deriving a chemical substitution rule.
- Section 4.1 delegates special servicing tools to the series 4140 powerhead manual. Its August 1999 table is now separately reviewed with exact tool restrictions. Located engine/component procedures are now separately reviewed; missing general-servicing and owner manuals remain documented source gaps, not complete manual acceptance.
- This is the 1999 English/USA introduction for BG 55, BG 65, BG 85, SH 55 and SH 85, series 4229. It does not cover BG 45/46, BR 45 C, an unlisted SH 65 or every later variant. Shared catalog headings do not widen these specifications. No serial threshold, physical interchange test or present production configuration is established.
TI dependency: TI 29/1999, p. 4 — Section 4.2 servicing aids, with 4.1 delegated tool context.
Manual evidence: STIHL Series 4140 powerhead service manual (1999-08), section Section 10, crankshaft-stub degreasant row only; wording conflict with TI29, PDF pages 1, 2, 18
Part numbers (1)
- 4229 007 1050 — Set of gasketsHistorical engine servicing aid · BG 55/65/85 and SH 55/85 engines; TI29/1999 section 4.2
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: historical repair times and BG45 heading conflict
Tenths-of-an-hour workshop times retain blank codes and the BG45 heading discrepancy; IPL availability is dated 02.99.
- The listed times assume trained personnel working in a properly equipped service workshop. They are hours expressed in tenths: 0.1 hour = 6 minutes, not decimal minutes. The note says this table for BG 55, BG 65, BG 85, SH 55 and SH 85 can be added to the STIHL repair-times table manual. These are historical workshop allowances, not measured owner repair times, current labor prices or guarantees.
- The printed left table heading is BG 45, BG 55, BG 65, BG 85; the right heading is SH 55, SH 85. BG 45 is absent from the bulletin title and the adjacent applicability note. Retain that internal discrepancy without inventing BG 45 applicability, deleting the printed heading or treating it as a proven typo. BG 46 and BR 45 C are not added from the later shared catalog.
- Every populated row has the same time in both printed columns: code 1 crankcase, crankshaft, crank bearings — 1.2 h; code 3 crankcase gasket/sealing — 1.0 h; code 4 crankshaft seals, including pressure and vacuum test — 1.0 h; code 5 cylinder and/or piston — 0.9 h; code 6 ignition module — 0.5 h; code 7 fuel hose (printed Fule Hose) — 0.5 h.
- Code 9 repair/rebuild carburetor — 0.8 h; code 10 replace carburetor or carburetor jet — 0.4 h, with the explicit instruction to use code 9 if repair was attempted. Code 11 throttle control/cable — 0.4 h; code 12 recoil starter — 0.5 h; code 13 fan housing/fan wheel — 0.5 h; code 14 discharge tube — 0.3 h; code 15 muffler — 0.5 h.
- Code 16 air filter, filter cover, tank cap, fuel filter, tank vent, spark plug and miscellaneous minor repairs — 0.3 h; code 17 stop switch — 0.4 h; code 18 fuel tank — 0.5 h; code 20 all other repairs — 0.5 h. Codes 2, 8 and 19 are blank, not zero-time tasks or missing numbers to fill. The table is not a diagnostic or repair procedure and does not define additive charging rules.
- Section 6 says an illustrated parts list is available for the new models and is included in the 02.99 microfiche and CD-ROM issue. This is a historical availability statement, not proof that the later retained catalog reconstructs the exact February 1999 edition, a production-change date, or present spare-part stock. Adding this self-contained time table to another manual does not require that manual to transcribe these rows. The footer, copyright, document identifiers and scissors/cut-line graphic add no fitment assertion.
- This is the 1999 English/USA introduction for BG 55, BG 65, BG 85, SH 55 and SH 85, series 4229. It does not cover BG 45/46, BR 45 C, an unlisted SH 65 or every later variant. Shared catalog headings do not widen these specifications. No serial threshold, physical interchange test or present production configuration is established.
Source: TI 29/1999, p. 6 — Sections 5.4 repair times and 6 spare parts availability.
No additional parts-table entry added.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: 4140 powerhead tightening torques
The August 1999 manual supplies five torque entries with thread-forming screw precautions and locking-tooth distinctions.
- Section 3.3, printed page 4 / PDF page 5: IS-DG5x60 spline screws, engine pan / crankcase / cylinder — 9.0 Nm; IS-DG5x60 spline screws, muffler / cylinder — 9.0 Nm; M8 starter cup — 17.0 Nm; M14x1.25 spark plug — 20.0 Nm; IS-DG4x20 spline screws, ignition module / cylinder — 4.5 Nm. These are component-specific tightening torques, not a universal torque for all screws of the same size.
- The three spline-screw entries carry remark 2: without locking teeth. Remark 1 means with locking teeth, but no row in this table is marked 1. Do not confuse screws with and without underhead locking teeth. The starter-cup and spark-plug rows have no numbered remark; no locking-tooth status is invented for them.
- DG and P (Plastoform) screws form a permanent thread on first installation in polymer or lightmetal components. The manual permits repeated removal and installation without impairing assembly strength only if the specified tightening torque is observed; a torque wrench is essential. This is not approval to reuse damaged screws or stripped threads.
- For an existing DG/P thread, place the screw in the hole and turn it counterclockwise until it drops slightly, then tighten clockwise to the specified torque. This engages the existing thread instead of forming another and weakening the assembly. Power-screwdriver limits for polymer are maximum 600 rpm for Plastoform screws and maximum 500 rpm for DG screws; these are tool-speed limits, not engine-speed settings.
- The manual’s safety section requires local and national regulations and the owner’s manual precautions if a machine is started during service. Fuel is highly flammable and can be explosive; no smoking, fire or flame near fuel, fuel work outdoors only, and spills wiped up immediately. The exact owner-manual dependency remains pending; these excerpts are not a complete operating procedure.
- TI29 sections 4.1 and 5.2 delegate tools and torques to the Series 4140 powerhead service manual. The retained August 1999 edition explicitly names BG 55, BG 65, BG 85, SH 55 and SH 85 in its introduction. These notes cover only that intersection with TI29, not every model listed in the manual or every later configuration. They do not replace the complete repair procedure, component manual or owner’s manual; no hardware work or physical interchange is verified.
TI dependency: TI 29/1999, p. 5 — BG/SH 55, 65, 85: 4140 powerhead tightening torques.
Manual evidence: STIHL Series 4140 powerhead service manual (1999-08), section Introduction, safety, 3.3 tightening torques, 9 special servicing tools; exact TI29 model intersection, PDF pages 1, 2, 3, 5, 17
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: restricted 4140 powerhead service tools
The delegated 1999 tool table preserves oil-seal side labels, puller and gauge alternatives, wrench ranges and shaft-tool exclusions.
- Section 9, printed page 16 / PDF page 17, lists the service tools below. They are historical workshop tools, not replacement components or quantities installed in the blower. Blank application cells for jaws 0000 893 3706 and screw bush 1108 893 4500 are not silently filled with an independent operation. The press-sleeve 1120 893 2400 application literally says clutch side in this multi-model manual; that wording does not establish that BG/SH has a clutch.
- Puller 5910 890 4400 is described as equivalent to 0000 890 4400, but with longer spindle 5910 890 8400. This is a qualified historical tool comparison, not an assertion that every spindle or jaw is interchangeable. Setting gauge 1111 890 6400 may be used instead of 1127 890 6400; the table does not itself specify an air-gap dimension.
- Torque wrenches 5910 890 0301 and 0302 cover 0.5 to 18 Nm; 5910 890 0311 and 0312 cover 6 to 80 Nm. The 0302 and 0312 entries carry the visual/acoustic-signal remark. Always use a torque wrench to tighten DG/P screws. Q-T27x150 screwdriver 5910 890 2400 may only be used for releasing these screws: the footnote prints GD/P, while the torque section and preceding footnote use DG/P. That lettering conflict is retained; it does not authorize tightening with the screwdriver.
- Assembly stand 5910 890 3100 and clamp 5910 890 8800 are listed for holding FS units, the clamp by the drive tube. The introduction describes shaft-driven FS, FC and HL machines, two washers and two M8 nuts. These are not a BG/SH mounting recipe: no blower clamping point, adapter or stand-fit claim is inferred from the shared engine manual. These two restricted items are deliberately excluded from the BG/SH tool roster.
- No test pressure, vacuum duration, disassembly sequence or equipment calibration is inferred from a tool-table entry. The located engine and component procedures are now separately reviewed; missing general-servicing and owner manuals remain documented source gaps.
- TI29 sections 4.1 and 5.2 delegate tools and torques to the Series 4140 powerhead service manual. The retained August 1999 edition explicitly names BG 55, BG 65, BG 85, SH 55 and SH 85 in its introduction. These notes cover only that intersection with TI29, not every model listed in the manual or every later configuration. They do not replace the complete repair procedure, component manual or owner’s manual; no hardware work or physical interchange is verified.
TI dependency: TI 29/1999, p. 4 — BG/SH 55, 65, 85: restricted 4140 powerhead service tools.
Manual evidence: STIHL Series 4140 powerhead service manual (1999-08), section Introduction, safety, 3.3 tightening torques, 9 special servicing tools; exact TI29 model intersection, PDF pages 1, 2, 3, 5, 17
Part numbers (23)
- 4221 893 5900 — Locking strip for pistonBlocking crankshaft · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 5910 890 4400 — PullerRemoving oil seals; equivalence limited by spindle note · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 0000 893 3706 — Puller jaws, profile No. 3.1 + 4Puller accessory; no separate application printed · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 0000 893 3700 — Puller jaws, profile No. 2Clamping engine pan and crankcase · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 1108 893 4500 — Screw bushPuller accessory; no separate application printed · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 1106 850 2905 — Carburetor and crankcase testerTesting carburetor and crankcase for leaks · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 0000 850 3501 — Vacuum pumpTesting crankcase for leaks · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 0000 855 8106 — Sealing plateSealing exhaust port for leakage test · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 1128 850 4200 — Test flangeLeakage test · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 1129 893 4600 — Assembly sleeveProtecting oil seal, starter side · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 1114 893 4601 — Press sleeveInstalling oil seal, starter side · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 1120 893 2400 — Press sleeveInstalling oil seal, printed clutch side · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 1127 890 6400 — Setting gaugeSetting air gap between ignition module and flywheel · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 5910 890 8210 — Crimping toolAttaching connectors to electrical wires · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 5910 890 0301 — Torque wrenchScrew connections, 0.5 to 18 Nm · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 5910 890 0302 — Torque wrench with visual/acoustic signalScrew connections, 0.5 to 18 Nm · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 5910 890 0311 — Torque wrenchScrew connections, 6 to 80 Nm · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 5910 890 0312 — Torque wrench with visual/acoustic signalScrew connections, 6 to 80 Nm · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 0812 542 2104 — Spline screw socket T27x125Tightening hexagonal socket-head screws · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 5910 890 2400 — Screwdriver Q-T27x150Hexagonal socket-head screws; DG/P loosening only · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 1114 893 4700 — Assembly driftInstalling piston pin · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 1108 893 4800 — Wooden assembly blockFitting piston · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
- 0000 893 2600 — Clamping strapCompressing piston ring · BG 55/65/85 and SH 55/85; historical 4140 powerhead tool reference, not an installed machine part
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: cylinder, piston and ring service limits
The 1999 powerhead manual requires a matched cylinder/piston, retained crankcase clamping, exact ring orientation and a new cylinder gasket.
- Sections 4.1–4.3, printed pages 5–7 / PDF pages 6–8: check and, if necessary, repair the fuel system, carburetor, air filter and ignition before seeking engine faults. The troubleshooting chart is delegated to Standard Repairs, Troubleshooting; housing, muffler, ignition module and spacer-flange removal are delegated to Components, Basic Engine 4140. Remove the spark plug. Those separate dependencies are not silently replaced by this note.
- Fit No. 2-profile jaws 0000 893 3700 to puller 5910 890 4400 and screw bush 1108 893 4500 to its spindle. Hold crankcase and engine pan together with the puller so they cannot separate when the cylinder is removed. Unscrew the cylinder-base screws, clamp the puller in a vice and pull off the cylinder. Inspect it; if a new cylinder is fitted, always fit its matching piston. The statement that new cylinders are supplied only with piston is historical supply guidance, not present stock or universal interchange.
- Remove the cylinder gasket and the B8x0.7 snap ring on the starter-cup side; the hookless flywheel-side snap ring stays in its groove. Drive out the piston pin with a 7 mm drift. If stuck, tap lightly while holding the piston steady so jolts do not reach the connecting rod. Remove the piston and inspect the needle cage; replace the crankshaft if necessary. The printed reference here says see 5.1, although section 5 is Crankshaft / ball bearings and 5.1 is Oil seals. Preserve that cross-reference discrepancy rather than treating oil-seal replacement as needle-bearing repair.
- For installation, thoroughly clean the gasket seat and oil the needle cage. The manual suggests heating the piston to ease installation but gives no piston-heating temperature here; the separate ball-bearing temperature must not be borrowed. The piston marking faces the exhaust side; the illustration separately labels the flywheel. Push the pin home against the hookless snap ring with drift 1114 893 4700, then install the B8x0.7 snap ring with its gap on the vertical piston axis, up or down.
- Fit a new cylinder gasket. Oil piston and rings, support the piston on wooden block 1108 893 4800 and position ring-gap radii against the fixing pin. Compress with strap 0000 893 2600 and recheck positioning. Oil the cylinder bore and align it to its installed orientation before sliding it over the piston; the manual warns that rings may break otherwise. The descending cylinder displaces the strap; remove strap and block, align cylinder and gasket, and tighten cylinder-base screws to 9.0 Nm with socket 0812 542 2104. Reassemble other parts in reverse sequence, observing the separately reviewed torque/thread precautions.
- For ring replacement, remove the piston first so cleaning and installation debris cannot fall into the crankcase. Remove the rings; use a piece of old piston ring to clean the grooves. Fit new rings with the gap radii facing the fixing pin, then reinstall the piston. The repeated source note literally says one (FS 45) or two (FS 45, 55) rings depending on model: FS 45 appears in both groups and no BG/SH ring count is specified there. Neither the illustration nor this note establishes a BG/SH count or replacement part number.
- TI29 section 5.3 delegates servicing of BG 55, BG 65, BG 85, SH 55 and SH 85 to the 4140 powerhead manual; the retained August 1999 introduction explicitly includes those models. These historical service notes apply only to that intersection, not to every model sharing a catalog page or to all later configurations. They do not replace the complete component, troubleshooting and owner manuals; located dependency sections are reviewed, while exact handbook edition, general-servicing and owner-manual sources remain documented gaps. No hardware procedure or physical interchange has been verified.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3; delegated BG/SH 55, 65, 85: cylinder, piston and ring service limits.
Manual evidence: STIHL Series 4140 powerhead service manual (1999-08), section BG/SH 55, 65, 85: cylinder, piston and ring service limits, PDF pages 1, 2, 6, 7, 8
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: crankshaft unit and engine-pan sealing
Crankshaft, connecting rod and needle bearing are replaced as a complete unit, with new bearings and seals; the manual preserves orientation and sealing requirements.
- Section 5, printed pages 7–8 / PDF pages 8–9: remove the cylinder, flywheel, starter cup and piston, then the holding puller. Pull the engine pan from the crankcase and lift out the crankshaft. Inspect bearings and seals. The crankshaft, connecting rod and needle bearing form an inseparable unit and must always be replaced as a complete unit; fitting a replacement crankshaft always requires new oil seals and ball bearings. No independently replaceable needle-cage part is inferred.
- Pull off seals and bearings and remove washers. On assembly, slip washers onto both crankshaft stubs, heat ball bearings to approximately 50 °C and push fully home. This is a bearing assembly temperature, not a piston, crankcase or seal heating specification. Grease seal lips and slide seals over the shaft ends with their open sides toward the ball bearings.
- Remove every trace of sealant from crankcase and engine-pan sealing faces. Install the shaft with the connecting rod toward the cylinder side and the short stub on the wide side of the crankcase, as shown in figure 232RA136. Apply a thin bead of sealant to the engine-pan mating face and follow the sealant manufacturer’s instructions; no bead dimension, cure time or pressure-test waiting interval is supplied here. Fit the pan and clamp it to the crankcase with the section 4.1 puller; assemble the remaining parts in reverse sequence.
- Section 10, printed page 17 / PDF page 18, identifies lubricating grease 0781 120 1111 (370 g tube) for oil seals and Dirko sealant 0783 830 2120 for sealing engine pan / cylinder. The procedure describes the crankcase/engine-pan mating faces, while the aid-table application reads engine pan / cylinder; both locators are retained, not an instruction to apply sealant indiscriminately to the new cylinder gasket. Historical product numbers do not establish current formulation or substitution.
- TI29 section 5.3 delegates servicing of BG 55, BG 65, BG 85, SH 55 and SH 85 to the 4140 powerhead manual; the retained August 1999 introduction explicitly includes those models. These historical service notes apply only to that intersection, not to every model sharing a catalog page or to all later configurations. They do not replace the complete component, troubleshooting and owner manuals; located dependency sections are reviewed, while exact handbook edition, general-servicing and owner-manual sources remain documented gaps. No hardware procedure or physical interchange has been verified.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3; delegated BG/SH 55, 65, 85: crankshaft unit and engine-pan sealing.
Manual evidence: STIHL Series 4140 powerhead service manual (1999-08), section BG/SH 55, 65, 85: crankshaft unit and engine-pan sealing, PDF pages 1, 2, 8, 9, 18
Part numbers (2)
- 0781 120 1111 — Lubricating grease, 370 g tubeOil-seal lubrication · Historical 4140 service aid for BG 55/65/85 and SH 55/85; not an installed part or current substitute
- 0783 830 2120 — Dirko sealantSealing engine pan / cylinder, as printed in service-aid table · Historical 4140 service aid for BG 55/65/85 and SH 55/85; follow manufacturer instructions, no cure time inferred
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: side-specific oil-seal replacement
The powerhead manual permits seal replacement without full engine dismantling and distinguishes starter-side and printed clutch-side tooling.
- Section 5.1, printed pages 9–10 / PDF pages 10–11, says complete engine disassembly is unnecessary for oil-seal replacement. Starter-side access requires starter-cup removal (8.2) and the housing-component handbook; the opposite side requires flywheel removal (7.2). Those access procedures remain separate dependencies, not an authorization to skip them.
- On both sides use puller 5910 890 4400 with No. 3.1 jaws 0000 893 3706, tension the arms and pull out the seal without damaging the crankshaft stub. This procedure selects No. 3.1, although the tool-table jaw description includes No. 3.1 + 4. Clean the sealing surface with a standard solvent-based degreasant containing neither chlorinated nor halogenated hydrocarbons, and grease the seal lips per section 10. TI29 prints hydrogenated instead of halogenated; the earlier aid note preserves that unresolved wording conflict. No chemical substitute is inferred.
- For the starter side, fit protective assembly sleeve 1129 893 4600 over the stub, slide the seal on with its open side toward the crankcase and press fully home using sleeve 1114 893 4601. Refit housing parts and starter cup. There is no numerical seal-depth tolerance in this passage.
- The other column is headed Clutch side and starts by removing the flywheel. After extraction and cleaning, slide the seal over an assembly sleeve with its open side toward the crankcase; the column does not repeat a sleeve part number. Press fully home with sleeve 1120 893 2400 (continued on PDF page 11), then refit the flywheel. The multi-model heading does not establish a BG/SH clutch, and the unnumbered assembly sleeve is not silently assigned a new part number.
- TI29 section 5.3 delegates servicing of BG 55, BG 65, BG 85, SH 55 and SH 85 to the 4140 powerhead manual; the retained August 1999 introduction explicitly includes those models. These historical service notes apply only to that intersection, not to every model sharing a catalog page or to all later configurations. They do not replace the complete component, troubleshooting and owner manuals; located dependency sections are reviewed, while exact handbook edition, general-servicing and owner-manual sources remain documented gaps. No hardware procedure or physical interchange has been verified.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3; delegated BG/SH 55, 65, 85: side-specific oil-seal replacement.
Manual evidence: STIHL Series 4140 powerhead service manual (1999-08), section BG/SH 55, 65, 85: side-specific oil-seal replacement, PDF pages 1, 2, 10, 11, 18
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: leak-test setup and conflicting pressure units
The 1999 manual specifies pressure and vacuum checks, but its bar/kPa pairs conflict by a factor of ten and its vacuum acceptance wording needs clarification.
- Sections 6–6.3, printed pages 10–12 / PDF pages 11–13: defective seals or gaskets and cracked spacer-flange castings can admit extra air, upset mixture, obstruct idle adjustment and cause an unsmooth transition to load. Pressure and vacuum checks address different leakage behavior; a pressure hold alone does not establish that oil seals remain tight on the induction stroke.
- Preparation is delegated to Machine components 4140 for shroud, carburetor and starter-cover removal. Set the piston at top dead centre, checked through the inlet port, and verify the spark plug is tightened. Fit a new spacer-flange gasket and test flange 1128 850 4200, with its nuts at 3.5 Nm. Slacken muffler screws half-way, place sealing plate 0000 855 8106 between gasket and cylinder exhaust port, completely filling the space between screws, and retighten moderately. No numeric temporary screw torque is supplied.
- For pressure testing the source connects tester 1106 850 2905 to the flange and closes the bulb vent screw. It prints a target of 0.5 bar (5 kPa), held constant for at least 20 seconds. These units are inconsistent: 0.5 bar equals 50 kPa, not 5 kPa. Both printed values are retained; this dimensional check is not an independently verified operating setpoint. Resolve the source conflict before any physical test rather than silently selecting either value.
- If indicated pressure drops, the manual calls for locating the leak and replacing the faulty part; coating the suspect area with oil and repressurizing reveals bubbles. Repeat the pressure test, then perform the vacuum test. The vacuum pump 0000 850 3501 connects to the same flange; close its vent and operate its lever. The printed vacuum target is again 0.5 bar (5 kPa), with the same tenfold unit discrepancy.
- The vacuum acceptance text literally says remains constant or rises to no more than 0.3 bar (3 kPa) within 20 seconds. It then says continued pressure rise (reduced vacuum) requires replacement of the oil seals. The 0.3 bar value equals 30 kPa, not 3 kPa. The rises wording and whether the indicated quantity is signed pressure or vacuum magnitude are not resolved here. No normalized pass/fail threshold or automatic test algorithm is inferred from this ambiguous sentence.
- After testing, open the vent screw before disconnecting the hose; remove the test flange and sealing plate, then tighten the muffler screws to 9.0 Nm. Pressure-test cleanup names starter cover, carburetor and shroud; vacuum cleanup names carburetor and shroud. Preserve the differing lists while retaining the shared preparatory removal of the starter cover; complete reassembly requires the component handbook. No test pressure, leakage result or repair success has been physically verified.
- TI29 section 5.3 delegates servicing of BG 55, BG 65, BG 85, SH 55 and SH 85 to the 4140 powerhead manual; the retained August 1999 introduction explicitly includes those models. These historical service notes apply only to that intersection, not to every model sharing a catalog page or to all later configurations. They do not replace the complete component, troubleshooting and owner manuals; located dependency sections are reviewed, while exact handbook edition, general-servicing and owner-manual sources remain documented gaps. No hardware procedure or physical interchange has been verified.
TI dependency: TI 29/1999, p. 5 — TI29 section 5.3; delegated BG/SH 55, 65, 85: leak-test setup and conflicting pressure units.
Manual evidence: STIHL Series 4140 powerhead service manual (1999-08), section BG/SH 55, 65, 85: leak-test setup and conflicting pressure units, PDF pages 1, 2, 11, 12, 13
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later engine removal and gasket placement
The later handbook retains distinct cable/rod disconnection paths and places the engine gasket in front of the inner fan housing.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Section 6.1, printed page 12 / PDF13: first remove the fan housing with rewind starter (7.2), fanwheel (10.1), filter housing (9.1) and handle molding (5.1). Fanwheel removal is reviewed in the separate later fan note; filter removal is reviewed separately in the later filter/choke note. Neither is established by this engine-access page alone. This is model-specific access evidence supplementing the shared powerhead handbook, not evidence of a blower clutch.
- Disconnect the short-circuit and ground wires from the ignition module, remove the retainers, and pull both fuel hoses off the carburetor elbow connectors. The illustration labels the two hoses but gives no part numbers or substitute hose specification.
- On a throttle-cable machine, disconnect the cable from the slotted pin on the throttle lever and push it out of the tensioner; remove the carburetor first if necessary and avoid kinking the cable. On a throttle-rod machine, remove the rod via section 8.6. This page does not map cable versus rod to a model year or serial range.
- Remove the engine mounting screws from the inner fan housing and lift out the engine. Reinstall in reverse sequence with the section 3.2 torques. Check that the illustrated gasket is in front of the inner fan housing; no new gasket number, dimension or interchange is inferred.
- The section 3.2 table lists IS-DG5x24 inner-blower-housing/crankcase and inner-blower-housing/engine-pan screws at 8.0 Nm each. Separate spiral-housing/crankcase and spiral-housing/engine-pan rows also use IS-DG5x24 but specify 6.0 Nm. Preserve those distinct joints; identical screw size does not make their torques interchangeable. The page does not establish the installation date of these housing variants.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 BG/SH 55, 65, 85: later engine removal and gasket placement.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section BG/SH 55, 65, 85: later engine removal and gasket placement, PDF pages 1, 2, 3, 4, 6, 7, 12, 13, 15
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later engine fault prerequisites and remedies
Engine fault tracing first checks filter, fuel, carburetor and ignition; oil-seal, crankcase and piston-ring remedies retain their powerhead-manual delegation.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 4.3, printed 10 / PDF11: always check and if necessary repair air filter, fuel system, carburetor and ignition before looking for engine faults. Ignition carries footnote1 referring to the Series 4140 Powerhead service manual, not an instruction to replace it on symptoms alone.
- Hard starting, idle stalling but normal full-throttle operation — faulty crankcase oil seals: install new seals; leaking/damaged (cracked) crankcase: seal/replace crankcase; leaking muffler: seal/replace muffler. The oil-seal and crankcase remedies carry the same powerhead-manual footnote. This table supplies neither leak-test pressures nor permission to choose between the retained conflicting pressure units.
- Incomplete power or erratic operation — worn/broken piston rings: install new rings (powerhead footnote); carbonized muffler/spark arresting screen: clean muffler inlet/exhaust openings and replace the screen; dirty air-filter element: fit a new element; kinked/cracked fuel or impulse line: fit new lines or route without kinks. Do not turn the screen-replacement wording into a screen-cleaning instruction.
- Engine overheating — insufficient cylinder cooling due to blocked fan-housing air inlets or very dirty cylinder fins: thoroughly clean all cooling-air passages and cooling fins. No fin clearance, temperature limit or running diagnostic experiment is specified.
- Footnoted engine service is already covered by the reviewed August1999 powerhead sections; this later symptom table does not establish compatibility across all revisions, a BG/SH piston-ring count, or a new sealant choice. Possible causes and their paired remedies remain distinct from a verified fault on a connected machine.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and separate handbook dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later engine fault prerequisites and remedies.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later engine fault prerequisites and remedies, PDF pages 1, 3, 4, 11
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the BG 45, BG 46, BG 55, BG 65, BG 85? Report a correction →