Stihl 4229 · Section B · 2 of 24 · 36 parts
Ignition system, Muffler
Fits BG 45, BG 46, BG 55, BG 65, BG 85.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (36)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4140 400 1200 | Flywheel | 1 |
| 2 | 0000 955 0802 | Collar nut M8x1 | 1 |
| 3 | 4229 400 1300 | Ignition module | 1 |
| 4 | 4229 431 2101 | Connector tag | 1 |
| 5 | 9075 478 3023 | Pan head self-tapping screw IS-D4x22 | 2 |
| 6 | 4229 448 1200 | Lead retainer | 1 |
| 7 | 4228 084 1100 | Spiral housing | 1 |
| 8 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 3 |
| 9 | 4229 140 0607 | Muffler | 1 |
| 10 | 4229 140 0608 | Muffler | 1 |
| 11 | 4229 140 0600 NLA | Muffler | 1 |
| 12 | 4229 140 0600 NLA | Muffler | 1 |
| 13 | 4229 140 6904 NLA | Stub with screen | 1 |
| 14 | 4229 140 6901 | Stub with screen | 1 |
| 15 | 4229 140 6905 | Stub with screen | 1 |
| 16 | 4229 145 6904 | Stub | 1 |
| 17 | 4229 145 6901 | Stub | 1 |
| 18 | 4229 145 6905 | Stub | 1 |
| 19 | 4140 149 0602 | Muffler gasket | 1 |
| 20 | 9075 478 4268 | Pan head self-tapping screw IS-D5x60 | 2 |
| 21 | 4229 140 0605 | Muffler | 1 |
| 22 | 4229 140 0606 | Muffler | 1 |
| 23 | 4229 140 0604 | Muffler | 1 |
| 24 | 4229 141 9001 | Screen | 1 |
| 25 | 9099 021 0805 | Self-tapping screw 4.2x6.5 | 1 |
| 26 | 4140 145 1200 | Flange | 1 |
| 27 | 4140 149 0602 | Muffler gasket | 2 |
| 28 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 2 |
| 29 | 4229 140 0605 | Muffler | 1 |
| 30 | 4229 140 0606 | Muffler | 1 |
| 31 | 4229 141 9001 | Screen | 1 |
| 32 | 9099 021 0805 | Self-tapping screw 4.2x6.5 | 1 |
| 33 | 4140 145 1200 | Flange | 1 |
| 34 | 4140 149 0602 | Muffler gasket | 2 |
| 35 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4229 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: electronic magneto and suppressed spark plugs
TI29 names Bosch WSR 6F, NGK BPMR 7 A or Champion RCJ 6Y; no plug gap or ignition-module part number is given.
- Ignition module: electronic magneto ignition. Suppressed spark plug choices printed in section 2.1.3 are Bosch WSR 6F, NGK BPMR 7 A or Champion RCJ 6Y. The source supplies no plug gap, tightening torque, ignition timing, module air gap, maximum RPM or numbered module identity; none is inferred.
- Later SCS 01-2012 BG and SH crankcase/cylinder sheets list NGK BPMR7A as 0000 400 7000 and Bosch WSR 6 F as 1110 400 7005, both at position 15. These catalog identities are comparison evidence, not part numbers printed in TI29. No numbered Champion replacement is established, and absence of a Champion row does not erase the historical third plug choice. Catalog rows remain unchanged.
- This is the 1999 English/USA introduction for BG 55, BG 65, BG 85, SH 55 and SH 85, series 4229. It does not cover BG 45/46, BR 45 C, an unlisted SH 65 or every later variant. Shared catalog headings do not widen these specifications. No serial threshold, physical interchange test or present production configuration is established.
Source: TI 29/1999, p. 3 — Section 2.1.3 ignition system.
No additional parts-table entry added.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: ignition diagnosis and module installation
A visible spark does not prove correct timing; the manual specifies a molded lead, ground-wire location and gauge-set module mounting.
- Sections 7–7.1.2, printed pages 12–14 / PDF pages 13–15, warn that ignition-system high voltages can cause serious or fatal accidents. Diagnosis begins with the spark plug and the separate Standard Repairs, Troubleshooting handbook. The breakerless system consists primarily of module and flywheel; the coil body has a high-voltage output with ignition lead and a short-circuit-wire connector tag.
- The source says accurate module testing needs sophisticated equipment and describes a workshop spark test. Its no-spark replacement instruction is conditional on checking that the wiring and stop switch are in good condition first. No module replacement is inferred merely from an unchecked no-spark symptom. Section 10 lists electrical repair kit 5910 007 1050 for the electrical system; no kit contents or module compatibility are specified there.
- Ignition timing is not adjustable. Lack of mechanical wear does not exclude an internal circuit fault: the switching point can change while a spark test still appears satisfactory, leaving timing outside tolerance and impairing starting or running. No timing tolerance, timing angle or electronic correction procedure is supplied in this section.
- Remove the relevant shroud or housing via the component handbook. Disconnect short-circuit and ground wires, pull the boot from the plug, undo the screws and remove the module. The ignition lead is molded to the module, not described as independently removable here.
- Place the module and insert screws loosely. Secure the ground-wire connector tag with the upper screw; put setting gauge 1127 890 6400 between the module arms and flywheel magnet poles. Press the module against the gauge and tighten mounting screws to 4.5 Nm, then reassemble remaining parts in reverse sequence. This section gives a gauge-based setting, not a newly measured air-gap dimension; the already reviewed specification and tool-table alternatives remain separate evidence.
- TI29 section 5.3 delegates servicing of BG 55, BG 65, BG 85, SH 55 and SH 85 to the 4140 powerhead manual; the retained August 1999 introduction explicitly includes those models. These historical service notes apply only to that intersection, not to every model sharing a catalog page or to all later configurations. They do not replace the complete component, troubleshooting and owner manuals; located dependency sections are reviewed, while exact handbook edition, general-servicing and owner-manual sources remain documented gaps. No hardware procedure or physical interchange has been verified.
TI dependency: TI 29/1999, p. 5 — TI29 section 5.3; delegated BG/SH 55, 65, 85: ignition diagnosis and module installation.
Manual evidence: STIHL Series 4140 powerhead service manual (1999-08), section BG/SH 55, 65, 85: ignition diagnosis and module installation, PDF pages 1, 2, 13, 14, 15, 18
Part numbers (1)
- 5910 007 1050 — Electrical repair kitElectrical-system servicing aid · Historical 4140 service aid in the TI29 BG 55/65/85 and SH 55/85 intersection; contents and current replacement not specified
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: flywheel inspection and shared-manual limits
Flywheel damage requires replacement; the shared manual retains clutch-access dependencies without establishing that a blower has a clutch.
- Section 7.2, printed page 14 / PDF page 15, first delegates clutch removal to Components, Basic Engine 4140. It then describes lightly tapping the crankshaft-stub end with a rubber mallet to free the flywheel and pulling the wheel off. This multi-model instruction does not establish a BG/SH clutch or a complete model-specific access procedure. The applicable component handbook remains necessary.
- Inspect the flywheel and magnet poles for cracks or other visible damage; if present, replace the flywheel. No replacement number, independent magnet replacement or physical interchange is established by this passage.
- Before installation the manual calls for degreasing the crankshaft stub and flywheel-hub bore with a standard commercial solvent-based degreasant containing neither chlorinated nor halogenated hydrocarbons. Section 10 repeats the crankshaft-stub application; TI29 uses hydrogenated instead of halogenated. That wording conflict remains unresolved and is not used to prescribe a chemical substitute.
- Fit the flywheel and check the position of its slot, then follow the component handbook for the printed clutch-installation step. The section does not independently specify a key part number, retention torque or slot alignment dimension. Remove the locking strip from the cylinder, refit the spark plug at 20 Nm, check and tighten any separate terminal nut, and refit the plug boot. The locking-strip removal presumes preceding component procedures; it is not evidence that those omitted steps have been verified on BG/SH hardware.
- TI29 section 5.3 delegates servicing of BG 55, BG 65, BG 85, SH 55 and SH 85 to the 4140 powerhead manual; the retained August 1999 introduction explicitly includes those models. These historical service notes apply only to that intersection, not to every model sharing a catalog page or to all later configurations. They do not replace the complete component, troubleshooting and owner manuals; located dependency sections are reviewed, while exact handbook edition, general-servicing and owner-manual sources remain documented gaps. No hardware procedure or physical interchange has been verified.
TI dependency: TI 29/1999, p. 5 — TI29 section 5.3; delegated BG/SH 55, 65, 85: flywheel inspection and shared-manual limits.
Manual evidence: STIHL Series 4140 powerhead service manual (1999-08), section BG/SH 55, 65, 85: flywheel inspection and shared-manual limits, PDF pages 1, 2, 15, 18
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later muffler variants and sealant wording
Catalytic and non-catalytic exhaust layouts require different gasket/screen handling; the sealant procedure and aid-table application wording do not match.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Sections 6.2–6.2.2, printed pages 13–14 / PDF14–15, distinguish mufflers without a catalytic converter from those with one. These are equipment-conditioned procedures, not proof that a catalytic version existed on every TI29 model in 1999. Both start with removal of the fan housing and rewind starter; troubleshooting is delegated to section 4.3.
- Without a catalytic converter, undo the screws and remove the muffler and exhaust gasket. Clean the sealing faces, use a new exhaust gasket and reinstall in reverse sequence. The procedure calls for sealant on the underside of the screw head and refers to section 12; it does not say to coat the new exhaust gasket.
- On machines with a removable stub, with or without a spark-arresting screen, unscrew the stub using a 15 mm wrench. Clean the screen or install a new stub if necessary. Clean the stub thread and coat it with sealant, following the sealant manufacturer instructions, then refit. The torque table gives stub/muffler 10.0 Nm and prints thread size M14x7; retain that unusual literal size, not an inferred pitch correction or replacement specification.
- For the catalytic layout, remove the screws and the muffler with exhaust gaskets and flange. Clean the sealing faces and install new exhaust gaskets on reassembly. The integrated catalytic converter is described as maintenance-free; the manual explicitly says never to attempt repairs on it. For its spark-arresting screen, remove the fan housing, undo the screen screw, withdraw the screen, clean or replace as necessary, and reassemble in reverse sequence. No screen-screw torque is given here.
- The torque table lists non-catalytic muffler/cylinder IS-DG5x60 and catalytic muffler/cylinder IS-DG5x24 screws at 9.0 Nm. This does not authorize swapping their lengths or transferring the removable-stub method to the separately illustrated catalytic screen.
- Section 12 lists Dirko gray sealant 0783 830 2120 in a 100 g tube, with application Guard on muffler, whereas section 6.2.1 refers to section 12 for screw-head underside and stub-thread sealant. Preserve this application-wording discrepancy rather than silently equating guard, screw head and thread, or inventing cure time. No current sealant substitute or universal exhaust-gasket coating is established. The same aid table specifies a solvent-based degreasant without chlorinated or halogenated hydrocarbons for cleaning sealing faces.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 BG/SH 55, 65, 85: later muffler variants and sealant wording.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section BG/SH 55, 65, 85: later muffler variants and sealant wording, PDF pages 1, 2, 3, 4, 6, 7, 14, 15, 39
Part numbers (1)
- 0783 830 2120 — Dirko gray sealant, 100 g tubeTable application: Guard on muffler · January2005 component-manual aid; procedural screw-head/stub-thread wording differs; no present substitute established
Wrong number or missing part for the BG 45, BG 46, BG 55, BG 65, BG 85? Report a correction →