Stihl 4229 · Section D · 4 of 17 · 18 parts
Rewind starter
Fits SH 55, SH 85.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (18)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4229 080 1802 | Fan housing | 1 |
| 2 | 9416 868 6650 | Rivet 6.5x0.5x8.8 | 1 |
| 3 | 4228 190 0600 | Rewind spring | 1 |
| 4 | 1123 195 0400 | Rope rotor | 1 |
| 5 | 0000 958 0923 | Washer | 1 |
| 6 | 1118 195 3500 | Spring | 1 |
| 7 | 1125 195 7200 | Pawl | 1 |
| 8 | 4140 195 3400 | Starter grip | 1 |
| 9 | 1120 195 8200 | Starter rope Ø 3x1060 mm | 1 |
| 10 | 0000 190 3404 | Starter grip ElastoStart Ø 3 mm | 1 |
| 11 | 0000 195 7000 | Cap | 1 |
| 12 | 0000 951 1100 | Screw IS-D5x20 | 3 |
| 13 | 9074 478 4425 | Pan head self-tapping screw IS-P6x19 | 1 |
| 14 | 4229 967 1501 | Model plate SH 55 | 1 |
| 15 | 4229 967 1503 | Model plate SH 85 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4229 080 2104 | Fan housing with rewind starter | 1 |
| — | 4229 080 2105 | Fan housing with rewind starter | 1 |
| — | 0000 930 2208 NLA | Starter rope Ø 3 mm x 30.5 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: historical starter rope and ElastoStart
TI29 lists rope 0000 195 8200 and ElastoStart 0000 190 3400; later catalog numbers and rope length differ.
- Page 2 describes ElastoStart as standard on BG 85 and SH 85 and otherwise optional. The page 4 ElastoStart accessory is a grip with rope, not a complete rewind assembly or a separate rope specification. No SH 65 is named.
- Page 3 specifies a single-pawl rewind starter and starter rope 3 mm (0.12 in) diameter, 800 mm (31.5 in) length in both engine columns. The page 4 rope row names use in the rewind starter and also ElastoStart, but does not independently state a packaged or cut length for each accessory. The specification does not imply a cutting or installation procedure.
- Later SCS 01-2012 BG and SH rewind sheets instead list rope 1120 195 8200, diameter 3 mm × 1060 mm, at position 9 and ElastoStart grip 0000 190 3404, diameter 3 mm, at position 10. They also show unpositioned 0000 930 2208 bulk rope, 3 mm × 30.5 m. These are not silently substituted for TI rope 0000 195 8200, its 800 mm engine specification, or ElastoStart 0000 190 3400; no numbered supersession is established.
- The 1999 USA issue names BG 55, BG 65, BG 85, SH 55 and SH 85, series 4229. Shared later catalog sheets also include BG 45/46; this note does not extend TI accessory applicability to those models, BR 45 C or later variants. No serial threshold or present-stock claim is supplied.
- Catalog comparisons preserve the later rows unchanged. Different part numbers or dimensions alone do not establish supersession, interchangeability or a retrofit procedure. Remaining technical specifications and service/manual references are still under review; this note does not close the entire TI.
Source: TI 29/1999, p. 2 · TI 29/1999, p. 3 · TI 29/1999, p. 4 — Section 3 starter accessories with sections 1 and 2.1.1 starter context.
Part numbers (2)
- 0000 195 8200 — Starter ropeUser accessory for rewind starter, also ElastoStart · BG 55/65/85; SH 55/85, section 3
- 0000 190 3400 — ElastoStart grip with ropeUser accessory; standard on BG 85/SH 85, optional on other named models · BG 55/65/85; SH 55/85, sections 1 and 3
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: rewind servicing and starter-cup torque
The manual distinguishes cold-stiffened lubricant from dirt contamination and specifies locking-strip use and 17.0 Nm starter-cup tightening.
- Sections 8–8.2, printed page 15 / PDF page 16: very stiff rope and slow or incomplete rewind may indicate a functioning but dirty starter mechanism. At very low temperatures, thickened rewind-spring oil can make windings stick. The cold-weather remedy described is a few drops of paraffin (kerosine) on the spring, then carefully pulling the rope out and allowing it to rewind several times until normal action returns. This is conditional historical guidance, not proof that every stiff starter is intact.
- For dirt or pitch contamination, remove and dismantle the entire mechanism including the rewind spring, taking particular care when removing the spring. Wash the parts in paraffin or white spirit, then lubricate spring and starter post with STIHL special lubricant before installation. Section 10 identifies 0781 417 1315 and describes its application as bearing bore in rope rotor and rewind spring in rope rotor. Retain both application descriptions; no current substitute or quantity is inferred.
- For starter-cup service, remove the starter cover through the component handbook and unscrew the spark plug. Fit locking strip 4221 893 5900 and unscrew the cup. Refit the starter cup at 17.0 Nm and reinstall other parts in reverse sequence. The illustrations show rotation arrows but the text does not name a thread hand; no left-hand thread is inferred. Spring preload, rope routing and component teardown details remain delegated, not invented from the general note.
- Section 11 lists unnumbered safety glasses and ElastoStart grip with rope 0000 190 3400. That ElastoStart number is already admitted from TI29 with exact standard/optional model limits and later-catalog conflicts; the general manual does not erase them. The brushcutter gear lubricants 0781 120 1117 (80 g) and 0781 120 1118 (225 g), and hedge-trimmer gear lubricants 0781 120 1109 (80 g) and 0781 120 1110 (225 g), are explicitly for other tool classes, not BG/SH gearbox or rewind lubricant recommendations.
- TI29 section 5.3 delegates servicing of BG 55, BG 65, BG 85, SH 55 and SH 85 to the 4140 powerhead manual; the retained August 1999 introduction explicitly includes those models. These historical service notes apply only to that intersection, not to every model sharing a catalog page or to all later configurations. They do not replace the complete component, troubleshooting and owner manuals; located dependency sections are reviewed, while exact handbook edition, general-servicing and owner-manual sources remain documented gaps. No hardware procedure or physical interchange has been verified.
TI dependency: TI 29/1999, p. 5 — TI29 section 5.3; delegated BG/SH 55, 65, 85: rewind servicing and starter-cup torque.
Manual evidence: STIHL Series 4140 powerhead service manual (1999-08), section BG/SH 55, 65, 85: rewind servicing and starter-cup torque, PDF pages 1, 2, 16, 18
Part numbers (1)
- 0781 417 1315 — STIHL special lubricantBearing bore in rope rotor and rewind spring in rope rotor · Historical 4140 starter-service aid for BG 55/65/85 and SH 55/85; no present formulation or substitute established
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later starter housing and integrated cup
The later handbook conditions its cup reference on a cup integrated in the flywheel and changes the cold-starter cleaning wording.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Sections 7.1–7.3, printed pages 14–15 / PDF15–16: remove the screws marked 1 and 2, then the fan housing with rewind starter; remove the antistatic wire if necessary. The illustration distinguishes the wire from the screws. It does not give a wire replacement number, omitted grounding permission or a universal screw torque.
- Section 7.3 applies specifically to machines with the starter cup integrated in the flywheel and refers their servicing to the Flywheel chapter of the Series 4140 Powerhead handbook. It does not prescribe a separate screw-off cup on that version. The August1999 powerhead handbook separately gives 17.0 Nm for a removable starter cup; that torque must not be applied to an integrated cup merely because both sources say 4140. The later page supplies no model-year or serial-number changeover for the integrated version.
- For a very cold, stiff/slow starter, section 7.1 names a few drops of standard solvent-based degreasant containing no chlorinated or halogenated hydrocarbons, followed by careful repeated pull-out/rewind until smooth action returns. This differs from the August1999 powerhead handbook wording paraffin (kerosine). Preserve the edition-specific descriptions; they are not proof of chemical equivalence or a current product recommendation.
- For dirt or pitch contamination, the whole mechanism including the rewind spring is removed and dismantled, taking particular care with the spring. Cleaning is referred to section 12. Lubricate the spring and starter post with STIHL special lubricant before installation; section 12 lists special lubricating oil 0781 417 1315 for the rope-rotor bearing bore and rewind spring. Rope-rotor dismantling, spring tension, rope and pawl procedures are covered separately in the later rotor/spring and rope/pawl notes; this access excerpt alone is not a complete starter overhaul.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 BG/SH 55, 65, 85: later starter housing and integrated cup.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section BG/SH 55, 65, 85: later starter housing and integrated cup, PDF pages 1, 2, 3, 4, 15, 16, 39
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later rotor and rewind-spring procedure
The 2005 handbook specifies spring-loop engagement, a clockwise clip and preload checks with at least half a turn of reserve.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Sections 7.4–7.5.1, printed pages 15–17 / PDF16–18, require starter removal via 7.2. Before rotor removal, relieve spring tension: the source says a broken rope leaves the spring untensioned; for an intact rope, pull out about 10 cm, hold the rotor steady, take three rope turns off it, pull the rope slightly farther and release the rotor so it spins back. The explicit removal precondition is that the rewind spring must not be under tension, not merely that a rope appears damaged.
- Remove the spring clip, washer and pawl, then carefully lift off the rotor. Coat the rotor bore with special lubricant, fit the rotor so its driver slips behind the inner spring loop, and check engagement by turning it slightly and letting it spring back. Lubricate and install the pawl, fit the washer and engage the clip in the starter-post groove. The clip must engage the pawl guide peg and point clockwise. A deformed clip can prevent correct operation; handle it carefully.
- For spring replacement, remove the rotor and broken spring pieces from the rotor and cover. Lubricate a new spring with a few drops of STIHL special lubricant; section 12 identifies 0781 417 1315. Place the spring and press its outer loop over the lug. The manual warns that it can pop out and uncoil if the rotor is not installed carefully.
- For a spring that has popped out, the historical procedure says wind it from inside outward and tension it to 55 mm diameter, then grip it with pointed-nose pliers about 10 mm from the end of the outer loop and place it in the starter. The illustrated inner-loop-to-hub distance A must be no more than 2 mm; correct it if necessary. These are assembly geometry values, not spring wire diameter, replacement-part dimensions or a measured result. Reinstall the rotor, then tension the spring.
- To tension, make a loop in the unwound rope, hold it near the rotor and use it to turn the rotor six full turns clockwise. Hold the rotor, pull out and straighten the rope with the grip, keep the rope tensioned, then release the rotor and slowly release the grip so the rope winds onto it. The grip must sit firmly in the guide bush without drooping; if not, add one turn.
- With the rope fully extended, the rotor must still turn at least another half turn before maximum spring tension. If it cannot, pull out the rope, hold the rotor and take off one rope turn. Do not overtension: the manual warns this causes spring breakage. Both grip seating and reserve-travel checks constrain the nominal six-turn preload; it is not an unconditional universal setting. Reinstall the starter with the appropriate section 3.2 fastener torques; no unlabeled screw torque is invented.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 BG/SH 55, 65, 85: later rotor and rewind-spring procedure.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section BG/SH 55, 65, 85: later rotor and rewind-spring procedure, PDF pages 1, 3, 4, 15, 16, 17, 18, 39
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later rope routing and pawl-only replacement
The later handbook distinguishes ordinary and ElastoStart grip routing and keeps the rotor on its post during pawl-only service.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Section 7.6, printed pages 17–18 / PDF18–19: remove the starter. For a broken rope, remove the remnants from rotor and grip; for a worn rope, first relieve rewind-spring tension via 7.4, pull the rope end from the rotor, undo its knot and withdraw it from grip, housing and rotor.
- Thread one end of the new rope through rotor and housing, tie a simple overhand knot and pull the rope back until the knot seats in the rotor recess. Thread the other end through the starter grip and tie a simple overhand knot. This section does not supply a rope length, diameter or part number; do not derive one from the drawing.
- On an ElastoStart-equipped machine, thread the new rope through the grip and spring element, tie a simple overhand knot, pull rope and spring element into the grip, then fit the cap. This conditional grip procedure does not make ElastoStart standard on every listed model or override TI29 accessory restrictions. Tension the spring via 7.5.1 and reinstall the starter via 7.2.
- Section 7.7: remove the starter, ease the clip off the starter post and pull the pawl out of the rotor. Do not pull the rope rotor off the post for this pawl-only operation. Lubricate the new pawl with the specified special lubricant and fit it, then push the clip into the starter-post groove so it engages the pawl guide peg and points clockwise. Handle the clip carefully: deformation can stop correct starter operation. Reinstall the starter. No pawl number or cross-model pawl interchange is established.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 BG/SH 55, 65, 85: later rope routing and pawl-only replacement.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section BG/SH 55, 65, 85: later rope routing and pawl-only replacement, PDF pages 1, 3, 4, 15, 16, 17, 18, 19, 39
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later starter symptom and cause table
Starter symptoms distinguish rope, spring, pawl, clip, dirt and cold lubricant causes; a symptom alone does not identify a failed part.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 4.1, printed 7 / PDF8: broken starter rope is paired with pulling too vigorously to the stop or over an edge rather than vertically, or normal wear; both rows say fit a new rope. Broken rewind spring is paired with overtension/no reserve at full rope extension, or heavy dirt/corrosion; both rows say fit a new rewind spring.
- Rope pulling out almost without resistance while the crankshaft does not turn has two alternatives: worn pawl guide peg/pawl — fit a new pawl; fatigued spring clip — fit a new clip. Neither row says every freely pulling rope requires both parts.
- Difficult pull and very slow rewind: a very dirty mechanism in dusty conditions calls for thorough cleaning of the complete starter. Very cold, viscous oil sticking the spring windings calls for coating the spring with standard solvent-based degreasant containing no chlorinated or halogenated hydrocarbons, then carefully pulling as often as necessary until normal action returns.
- The table says coat the spring; section 7.1 separately says a few drops. Neither provides a new quantitative dose or a current chemical substitute. August1999 powerhead kerosine wording remains separate, not proof of equivalence. Detailed disassembly, spring reserve and assembly precautions remain in the already reviewed starter sections7.1–7.7. The table is a set of possible causes/remedies, not a hardware diagnosis.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and separate handbook dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later starter symptom and cause table.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later starter symptom and cause table, PDF pages 1, 3, 4, 8
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the SH 55, SH 85? Report a correction →