Stihl 4229 · Section C · 3 of 17 · 26 parts
Carburetor, Air filter
Fits SH 55, SH 85.
Historical fitment & changes (34) — includes parts and conditions not shown on this drawing.
Parts (26)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4229 120 1800 | Filter | 1 |
| 2 | 4229 140 2801 | Filter housing | 1 |
| 3 | 4229 141 3700 | Lever | 1 |
| 4 | 4140 141 3700 | Lever | 1 |
| 5 | 9210 261 0700 | Hexagon nut M5 | 2 |
| 6 | 9417 003 7512 | Push nut 4.0x9.6x1.8 | 1 |
| 7 | 4229 141 3800 | Choke shutter | 1 |
| 8 | 4229 141 0501 | Filter cover | 1 |
| 9 | 4229 141 0500 | Filter cover | 1 |
| 10 | 4140 129 0900 | Gasket | 1 |
| 11 | 4114 149 1205 | Gasket | 1 |
| 12 | 4229 120 0606 | Carburetor C1Q-S68E | 1 |
| 13 | 4229 120 0603 | Carburetor C1Q-S64 → replaced by 4229 120 0606 TI 18/2002 | 1 |
| 14 | 4229 120 0604 | Carburetor C1Q-S55A → replaced by 4229 120 0603 TI 4/2001 | 1 |
| 15 | 4229 120 0600 | Carburetor C1Q-S50 | 1 |
| 16 | 4229 121 1601 | Spacer flange | 1 |
| 17 | 4229 121 1600 | Spacer flange | 1 |
| 18 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 2 |
| 19 | 4229 129 0900 | Gasket | 1 |
| 20 | 9007 319 1135 | Hexagon head screw M5x65 | 2 |
| 21 | 9007 319 1137 | Hexagon head screw M5x68 | 2 |
| 22 | 4229 122 1800 | Heat shield | 1 |
| 23 | 4114 149 1205 | Gasket | 1 |
| 24 | 9007 319 1137 | Hexagon head screw M5x68 | 2 |
| 25 | 4229 122 1800 | Heat shield | 1 |
| 26 | 4114 149 1205 | Gasket | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: balanced idle and left-hand LD adjustment
Fixed idle/full-load jets; LD seats counterclockwise and opens clockwise two turns. Historical idle range is 2500–3100 rpm.
- The original carburetor is an all-position diaphragm type with an integral fuel pump. Section 1 describes a balanced idle system with a fixed idle jet, fixed full-load jet and only one adjusting screw, LD. No carburetor maker/model, jet size or numbered carburetor is identified. Do not apply this single-LD procedure to every carburetor shown in a later shared IPL.
- Fuel tank capacity is 0.4 L (0.84 US pt). Section 2.1.2 gives idle speed 2500 to 3100 rpm and standard LD setting open two full turns, expressly referring to section 5.1. No fuel-oil ratio, gasoline grade or maximum engine speed is specified in these sections.
- Section 5 requires strict observance of local and national safety regulations and the owner’s manual safety precautions if the unit is started during repair or maintenance. This historical adjustment transcription is not a substitute for that manual or authorization for unattended engine operation; the exact owner-manual dependency remains under review.
- For idle adjustment, first check the air filter and replace it if necessary. LD has a left-hand thread: carefully seat it counterclockwise, then open it two full turns clockwise for the standard setting. Do not reverse these directions by importing a conventional right-hand H/L screw procedure or force the seat.
- The source then calls for starting and warming the engine and setting idle with LD so the engine does not stop at idle and accelerates smoothly when the throttle is opened. If it stops while idling, turn LD about 1/2 turn clockwise until it runs smoothly. For erratic idling or poor acceleration, turn LD about 1/2 turn counterclockwise until it runs smoothly. These are symptom-specific historical corrections, not repeated unlimited turns or separate mixture-jet settings.
- The page 2 footnote delegates a detailed balanced-idle description to the Carburetors handbook dated November 1998 or later. The separately reviewed balanced-idle-flow note now supplies section5.2.4 from a recovered copyright1999 handbook; its exact edition is unknown and the broader service dependency remains partial. Later SCS 01-2012 BG/SH carburetor sheets include C1Q-S50, C1Q-S55A, C1Q-S64 and C1Q-S68E; their presence does not identify the unnamed 1999 carburetor or extend the LD directions to them. No numbered supersession is inferred here.
- This is the 1999 English/USA introduction for BG 55, BG 65, BG 85, SH 55 and SH 85, series 4229. It does not cover BG 45/46, BR 45 C, an unlisted SH 65 or every later variant. Shared catalog headings do not widen these specifications. No serial threshold, physical interchange test or present production configuration is established.
Source: TI 29/1999, p. 2 · TI 29/1999, p. 3 · TI 29/1999, p. 5 — Section 1 carburetor; 2.1.2 fuel system; 5 repair warning and 5.1 carburetor adjustment.
No additional parts-table entry added.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later air-filter and choke service
Foam, felt and multi-ply felt filters require different care; a multi-ply conversion omits foam, and choke reassembly uses a new push nut.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Sections 9.1–9.1.2, printed pages 21–22 / PDF22–23: a dirty air filter can reduce power, raise fuel consumption and make starting harder; check for a plugged filter when power noticeably falls. Before removal, close the choke shutter and remove loose dirt around the filter. A damaged filter must be replaced immediately.
- Wash the foam filter in the specified standard solvent-based degreasant containing no chlorinated or halogenated hydrocarbons, then dry it; replace if necessary. Felt and multi-ply felt filters are to be replaced, not washed. As a temporary measure, knock them out on the palm of the hand or blow clear with compressed air. No air pressure, solvent brand, soak time or present-day chemical substitute is established.
- If a felt filter is replaced by a multi-ply filter, do not reinstall the foam filter. This is an explicit conditional assembly rule, not proof that all listed models originally used the same filter or that arbitrary filter media interchange. No replacement number, date cutoff or kit is provided.
- To remove/install, squeeze the cover retainers together, swing the cover aside and pull its lugs out of the guides, remove the filter, then undo the nuts and remove the filter housing. The next column repeats dry clearing and no washing; read with 9.1 this does not override its distinct foam-washing instruction. Replace a heavily loaded filter and always replace a damaged one.
- On machines with a catalytic converter, remove the gasket and heat shield; use new gaskets on reverse assembly. This equipment-conditioned branch is not evidence of a catalytic version on every TI29 model in 1999. The section gives no filter-housing nut torque; do not transfer an unrelated fastener torque.
- For the choke shutter, remove the air filter via 9.1.1, remove the push nut and pull the shutter out of its lever. On installation, correctly locate the shutter in the lever guide and use a new push nut, then complete reverse assembly. The diagram callouts are not replacement numbers; no reuse permission, torque or unrelated choke interchange is established.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 BG/SH 55, 65, 85: later air-filter and choke service.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section BG/SH 55, 65, 85: later air-filter and choke service, PDF pages 1, 3, 4, 12, 22, 23
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later carburetor leakage test
The later carburetor test specifies approximately 0.8 bar; it is not the powerhead crankcase pressure test and gives no timed pressure-loss tolerance.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Section 9.2.1, printed page 23 / PDF24, refers fuel-system faults to troubleshooting 4.2 and also requires checking or cleaning the tank vent via 9.5 for carburetor or fuel-supply problems. The vent test/replacement is reviewed separately; troubleshooting4.2 is reviewed in the separate diagnosis notes; a carburetor result alone does not establish correct fuel delivery.
- Remove the air filter via 9.1.1 and disconnect the fuel hose from the carburetor elbow. Push fuel line 1110 141 8600 onto nipple 0000 855 9200, fit that line to the carburetor elbow, and connect the pressure hose of carburetor/crankcase tester 1106 850 2905 to the nipple. These numbers identify the historical test setup, not installed replacement fuel hoses or an interchangeable modern kit.
- Close the rubber-bulb vent screw and pump until the gauge reads approximately 0.8 bar. The source says the carburetor is airtight if pressure remains constant. It specifies no hold time, allowable pressure decay or calibrated measurement uncertainty. Do not apply this carburetor value to crankcase testing or resolve the separate powerhead manual pressure-unit conflicts with it.
- For falling pressure, the page names an inlet needle that does not seal (foreign matter in the valve seat, damaged needle sealing cone or sticking inlet control lever), or a damaged metering diaphragm. In either case service the carburetor; this is a source fault list, not proof of a unique diagnosis from pressure drop alone.
- After testing, open the vent screw before pulling off the test fuel line, reconnect the machine fuel hose to the elbow, and assemble the other parts in reverse sequence. Always install a new gasket. No engine run, fuel-system pressure test or hardware validation was performed for this reference note.
- The separately reviewed Carburetors handbook7.1 PDF25 adds fuel-wetted preparation, a dry-carburetor limit of0.35 bar (5 psi) and a maximum test pressure of1 bar (14.5 psi) around its approximately0.8-bar test. Those are supplementary generic handbook conditions, not new claims that the later2005 page states them, not crankcase values and not a verified hardware procedure.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 later carburetor leakage test.
Manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later carburetor leakage test, PDF pages 1, 3, 4, 24 · Carburetors (publication revision unestablished; ©1999), section Supplementary wet/dry leakage conditions:7.1, PDF pages 1, 2, 25
Part numbers (3)
- 1106 850 2905 — Carburetor and crankcase testerHistorical carburetor leakage-test setup · Later2005 BG/SH component carburetor test; not an installed replacement machine part
- 1110 141 8600 — Fuel line for test adapterConnect carburetor elbow to test nipple · Later2005 BG/SH component carburetor test; not an installed replacement machine part
- 0000 855 9200 — Test nippleConnect test line to tester pressure hose · Later2005 BG/SH component carburetor test; not an installed replacement machine part
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later carburetor removal and spacer flange
Cable and rod access remain distinct; spacer-flange service preserves new gaskets, the binding-head screw restriction and a wrong printed cross-reference.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Section 9.2.2, printed page24 / PDF25: remove the air filter via 9.1.1 and disconnect the fuel hoses from the carburetor elbow connectors. On cable-equipped machines disconnect the cable from the slotted pin on the throttle lever; on rod-equipped machines remove the throttle rod via 8.6. Remove the carburetor and gasket. Reinstall with new gaskets, keep the fuel hoses free of kinks and observe the appropriate tightening torques in 3.2.
- Section 9.2.3 begins Remove the carburetor but prints reference 9.1.1, which is the air-filter section; the actual carburetor-removal heading is 9.2.2. Preserve the printed cross-reference conflict rather than treating air-filter removal as complete carburetor removal.
- For the spacer flange, pull the throttle cable out of the flange on cable-equipped machines. The cable and rod branches each remove their illustrated screws and lift the flange together with the hex-head screws. These are separate illustrated configurations, not permission to interchange flange or linkage versions.
- The continuation on printed page25 / PDF26 removes the gasket from its guides on the spiral housing. Reinstall in reverse sequence, always using new gaskets and observing 3.2. The figures identify gasket location and screw positions, not replacement part numbers.
- The 3.2 table, printed page5 / PDF6, specifies IS-DG5x24 spacer flange/cylinder screws at 6.0 Nm with binding head (remark1). This is not a torque for carburetor internal screws, mounting nuts or any other joint. For an existing DG/P thread, turn the screw counterclockwise until it drops into the old thread, then tighten clockwise to specified torque; use a torque wrench. Power-driver maxima are 500 rpm for DG and 600 rpm for Plastoform screws. Do not mix screws with and without binding heads.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 later carburetor removal and spacer flange.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later carburetor removal and spacer flange, PDF pages 1, 3, 4, 6, 7, 25, 26
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later manual fuel-pump cover variants
Oval and square end covers have distinct access sequences; oval-cover screw lengths and conditional hole alignment are retained without inferring a retrofit.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Sections 9.3.1–9.3.2, printed pages25–26 / PDF26–27, distinguish a manual fuel pump with oval end cover from one with square end cover. The oval subsection first directs the leakage test via 9.2 and carburetor removal via 9.2.2. These are manual pump components, not an electrically actuated pump.
- For the oval cover, remove the M3x12 screws and end cover with cap; remove the M3x8 screws and flange, then take the cap out of the end cover. Inspect the metering diaphragm and gasket via 9.3.3 and replace if necessary. Reassemble in reverse sequence. Additional holes in gasket and diaphragm, if present, must align with those in the carburetor and flange.
- For the square cover, take out the screws, remove the end cover with cap, take the cap out and remove the flange. Inspect the metering diaphragm and gasket via 9.3.3 and replace if necessary, then reverse the assembly sequence. This subsection gives no screw dimensions; do not transfer the oval-cover M3x12/M3x8 assignment to it.
- No cover-to-model-year mapping, part number, screw torque or interchange between oval and square assemblies is established by these pages. The manual uses cover shape to distinguish the procedures; catalog navigation does not select a physical variant.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 later manual fuel-pump cover variants.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later manual fuel-pump cover variants, PDF pages 1, 3, 4, 24, 25, 26, 27
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later metering diaphragm and inlet needle
Metering-side gasket order and compensating-bore alignment are explicit; the inlet lever must move freely and its upper edge be flush with the carburetor body.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Section 9.3.3, printed pages26–27 / PDF27–28: remove the appropriate oval- or square-pump flange using 9.3.1 or 9.3.2, then remove the metering diaphragm and gasket from the body. If stuck together, separate them very carefully. Inspect both and replace as necessary; distortion or swelling from fatigue requires diaphragm replacement.
- Fit the gasket on the carburetor body first, aligning its hole with the compensating bore. Place the metering diaphragm on the gasket and align its hole with the bore and gasket. Complete the appropriate cover assembly via 9.3.1 or 9.3.2. This is the metering-side order, not a substitute for the pump-side stack.
- Section 9.3.4 removes the metering diaphragm, the retaining screw, inlet control lever, spindle, spring and inlet needle. Take care because the spring may pop out. An annular indentation in the needle sealing cone requires replacement because it will no longer seal properly; do not treat a worn groove as an adjustment mark.
- Reassemble in reverse sequence: engage the clevis in the annular groove on the needle head, locate the helical spring on the control-lever nipple and check that the lever moves freely. The upper edge of the inlet control lever must be flush with the top of the carburetor body. Reinstall the metering diaphragm via 9.3.3. The needle-head engagement groove is distinct from the damage indentation on the sealing cone.
- No numerical lever clearance, bending method, replacement needle/diaphragm number, spring substitution or retaining-screw torque is supplied. The flush reference is the carburetor body, not a gasket surface or a generalized gauge value for other carburetors.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 later metering diaphragm and inlet needle.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later metering diaphragm and inlet needle, PDF pages 1, 3, 4, 26, 27, 28
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later fixed-jet removal limits
Fixed-jet removal covers C1Q-S48, C1Q-S50, C1Q-S55 and C1Q-S64, C1Q-S73 only; no jet size or machine assignment is established.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Section 9.3.5, printed page28 / PDF29: avoid damaging the fixed jet during removal and first remove the metering diaphragm via 9.3.3. The first illustration is expressly C1Q-S48, C1Q-S50, C1Q-S55 carburetors only; the second is C1Q-S64, C1Q-S73 carburetors only. Each instructs unscrewing the illustrated fixed jet and reassembling in reverse sequence.
- The two illustrations preserve different locations. The caption callout1 is not a jet part number. No jet size, calibration, tightening torque, interchange or conversion between the two groups is given. These captions do not establish that each named carburetor was fitted to every linked model, or to a 1999 machine.
- The TI29 model intersection remains BG55/65/85 and SH55/85; the procedure additionally requires the actual named carburetor variant. A later catalog carburetor identity or current production fitment must not be inferred from a shared series link.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 later fixed-jet removal limits.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later fixed-jet removal limits, PDF pages 1, 3, 4, 27, 28, 29
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later pump diaphragm and fuel strainer
Pump-side diaphragm and gasket location follows the end-cover pegs; contaminated or damaged strainers and fatigued diaphragms require inspection and replacement.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit. The manual separately distinguishes stop-switch versions up to/from 2001; the overlapping year labels do not establish an exact production or serial cutoff.
- Section 9.3.6, printed page28 / PDF29: remove the carburetor via 9.2.2, remove the screw and end cover, then remove the gasket and pump diaphragm. If stuck together, remove and separate them very carefully. A diaphragm distorted or swollen by fatigue must be replaced; inspect diaphragm and gasket and replace if necessary.
- Examine the fuel strainer for contamination and damage and replace if necessary. No strainer cleaning solvent, mesh grade, replacement number or permission to omit the strainer is supplied.
- Reassemble in reverse sequence. Figure932RA259 shows pump diaphragm1 and gasket2 located by the pegs on end cover3, with the gasket adjacent to the end cover and the diaphragm on the body side. Preserve this pump-side stack rather than transferring the metering-side body/gasket/diaphragm sequence.
- The figure is an assembly-location instruction, not a dimensioned replacement specification. No cover-screw torque, diaphragm interchange or engine/carburetor year assignment is established by this subsection.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; later2005 later pump diaphragm and fuel strainer.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later pump diaphragm and fuel strainer, PDF pages 1, 3, 4, 25, 29
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later LD-only carburetor adjustment
The LD screw has a left-hand thread: seat counterclockwise, then open two full turns clockwise; H/L mixture screws are absent.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 9.4.1, printed 29 / PDF30, applies to the carburetor with LD idle-speed screw and no H maximum-speed or L idle-mixture adjusting screws. The manual describes its mixture as tuned for operating conditions; this is a design statement, not measured performance on an owner machine. Do not transfer H/L/LA or limiter-cap instructions to this variant.
- For the standard setting from scratch, carefully turn LD counterclockwise onto its seat because it has a left-hand thread, then turn it two full turns clockwise. Check the air filter and replace if necessary. Check the spark-arresting screen and clean or replace as necessary.
- The LD subsection prints 9.1 for the air-filter check and 7.2 for the spark-arresting screen. Section 7.2 is rope rotor/pawl, not the screen; the adjacent H/L/LA subsection instead prints 6.2 for the screen and 9.1.1 for the air filter. Preserve the erroneous 7.2 reference; the reviewed muffler/screen variants are in 6.2, not an invented starter-screen procedure.
- For idle adjustment, first carry out the standard setting and warm the engine. If it stops at idle, slowly turn LD clockwise until it runs smoothly. For erratic idle or poor acceleration, slowly turn LD no more than half a turn counterclockwise. This subsection supplies no numerical idle rpm or high-speed adjustment; do not import the later H/L/LA basic-setting speeds.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later LD-only carburetor adjustment.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later LD-only carburetor adjustment, PDF pages 1, 3, 4, 14, 16, 30
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later H/L/LA user carburetor adjustment
User adjustment leaves the H limiter cap in place; its limited travel is not the uncapped basic-setting range.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 9.4.2, printed 29–30 / PDF30–31: do not remove the H limiter cap for the standard setting. Only fine correction of H is available. Check the air filter via 9.1.1 and replace if necessary; check the spark-arresting screen via 6.2 and clean or replace as necessary.
- Turn H counterclockwise as far as the stop, no more than 3/4 turn. Carefully seat L clockwise, then open L one full turn counterclockwise. Start and warm the engine. These directions differ from the LD left-hand thread and from the uncapped H basic setting of 1 1/2 turns.
- For altitude/sea-level fine tuning, first perform the standard setting, warm the engine and open the throttle wide. At high altitude turn H clockwise (leaner), never beyond the stop, until there is no noticeable rpm increase. At sea level turn H counterclockwise (richer), never beyond the stop, until there is no noticeable rpm increase. Very small corrections affect running; the standard setting may already give the highest rpm in either case. No numeric full-throttle limit is specified in this user subsection.
- For idle, open L one full turn and warm the engine. If it stops at idle, slowly turn LA clockwise until it runs smoothly. Erratic idle with poor acceleration is described as too lean: turn L about a quarter turn counterclockwise until running and acceleration are smooth. Erratic idle described as too rich instead calls for about a quarter turn clockwise. These are source symptom branches, not a unique diagnosis from erratic idle alone.
- It is usually necessary to adjust LA again after each L correction. No carburetor-to-model-year assignment, permission to defeat the stop, or universal adjustment for other variants follows from these pages.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later H/L/LA user carburetor adjustment.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later H/L/LA user carburetor adjustment, PDF pages 1, 3, 4, 30, 31
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later H/L/LA basic setting and limiter caps
The basic-setting sequence preserves the 3,700 rpm abort threshold and different short/long limiter-cap seating depths.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 9.4.3, printed 31–32 / PDF32–33: remove the H limiter cap only when necessary to replace H, clean the carburetor or adjust from scratch. After removal, a basic setting is required; cap removal is not part of the user standard setting. This historical service procedure is not evidence of an uncapped production configuration.
- For a short limiter cap, insert puller 5910 890 4501 between cap and carburetor with its groove facing the operator, then pry off the cap. If stuck on the screw, turn the puller so its groove faces the carburetor and pry off. A long limiter cap instead uses suitable pliers. No cap replacement number or cross-variant interchange is supplied.
- Seat H and L clockwise, then open H 1 1/2 turns and L one full turn counterclockwise. Check the air filter and clean or replace as necessary; warm the engine. Use a tachometer and adjust the specified engine speeds within the printed tolerance of +/- 200 rpm.
- The ordered sequence is: (1) set 3,300 rpm with LA; (2) turn L either way for maximum rpm, but if that speed is higher than 3,700 rpm, abort and restart at step 1; (3) reset 3,300 rpm with LA; (4) set 2,800 rpm with L; (5) set maximum engine speed 10,500 rpm with H. Preserve the literal higher-than 3,700 abort rule; the general tolerance does not authorize raising that threshold. These are this later H/L/LA procedure values, not LD settings or proof of a 1999 specification.
- Always install a new limiter cap; used caps may have been damaged during removal. For a short cap, align against the rich stop and press only to the second noticeable detent. Its stop limits H to 3/4 turn (270 degrees); do not press the short cap against the carburetor body because it would be damaged.
- For a long cap, align against the rich stop so H can rotate only 3/4 turn clockwise, then push the cap until it butts against the carburetor body. The long-cap seating instruction is deliberately opposite to the short-cap warning. After either cap installation, carry out the standard setting via 9.4.2. No cap-depth dimension, running attachment configuration or extra calibration condition is invented.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later H/L/LA basic setting and limiter caps.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later H/L/LA basic setting and limiter caps, PDF pages 1, 3, 4, 32, 33
Part numbers (1)
- 5910 890 4501 — Puller for short limiter capShort-cap removal only; long cap uses suitable pliers · January2005 component service setup only; not an installed machine part or universal substitute
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later fuel-tank vent test
Tank-vent vacuum should slowly disappear; unchanged vacuum calls for vent replacement, unlike an airtight-carburetor test.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 9.5.1, printed 32 / PDF33, states that carburetor operation requires atmospheric and internal fuel-tank pressure to equalize through the vent. For carburetor or fuel-supply trouble, always check the vent and replace it if necessary. This does not make the vent the unique cause of a running fault.
- Open the tank cap slowly, drain the tank, then refit the cap tightly. Disconnect the fuel hoses from the carburetor via 9.2.2, seal one hose with a suitable plug, and connect vacuum pump 0000 850 3501 to the other hose. Operate the pump quickly to produce a vacuum in the tank.
- If vacuum remains unchanged, install a new vent via 9.5.2. If vacuum slowly disappears, the manual calls the vent in order. This is the opposite of retaining pressure for an airtight carburetor: do not confuse tank-vent, carburetor and crankcase criteria. No numerical vacuum target, elapsed time, decay rate, plug size or positive-pressure test is provided.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later fuel-tank vent test.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later fuel-tank vent test, PDF pages 1, 3, 4, 33
Part numbers (1)
- 0000 850 3501 — Vacuum pumpHistorical tank-vent test setup · January2005 component service setup only; not an installed machine part or universal substitute
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later fuel-system pressure-unit conflicts
All three bar/kPa pairs in the 2005 specifications differ by a factor of ten; none is silently chosen as an operating limit.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 3.1, printed 4 / PDF5, identifies a diaphragm carburetor and prints carburetor leakage test at gauge pressure 0.8 bar (8 kPa), tank-vent operation at gauge pressure 0.3 bar (3 kPa), and under vacuum 0.05 bar (0.5 kPa). These are literal source pairs, not equivalent-unit values.
- Using 1 bar = 100 kPa, the printed bar values correspond arithmetically to 80 kPa, 30 kPa and 5 kPa respectively, ten times the parenthetical values. This is a dimensional contradiction, not authority to select either member as the intended or safe test pressure. The source does not resolve which entries are wrong.
- The later carburetor procedure 9.2.1, printed 23 / PDF24, separately says approximately 0.8 bar, without the conflicting kPa parenthesis. Tank-vent procedure 9.5.1, printed 32 / PDF33, supplies no numerical target and judges unchanged vacuum versus slowly disappearing vacuum. Keep those procedure-specific statements separate; do not retrofit an invented decay time, positive-pressure method or selected threshold from the conflicting specification table.
- Tank-vent operation, carburetor leakage and crankcase sealing are different tests. These later-manual conflicts do not resolve the separate August1999 powerhead pressure/vacuum wording conflicts. No physical pressure test was performed and no operational threshold is endorsed.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later fuel-system pressure-unit conflicts.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later fuel-system pressure-unit conflicts, PDF pages 1, 3, 4, 5, 24, 33
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later fuel and catalytic oil restrictions
The later specification gives minimum 90 RON and a conditional 50:1 ratio; catalytic units explicitly require STIHL 50:1 oil with unleaded gasoline.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 3.1, printed 4 / PDF5, refers Fuel to the instruction manual and gives minimum octane number 90 RON. RON is retained as printed, not equated with a pump AKI rating or converted using an assumed fuel composition. The exact owner-manual dependency remains open.
- The general fuel-mixture row says regular brand-name gasoline and STIHL 50:1 two-stroke engine oil or brand-name two-stroke engine oil. Its mix-ratio row specifies 50:1 with STIHL 50:1 two-stroke engine oil. It does not assign that ratio to every alternative oil or supply another ratio for such oils.
- The separate catalytic-converter paragraph says to use only STIHL 50:1 two-stroke engine oil with unleaded gasoline. Preserve the catalytic restriction without extending its wording to every non-catalytic variant or treating this 2005 text as proof of original1999 catalyst equipment.
- No ethanol percentage, storage interval, alternative lubricant approval, current product recommendation or machine-specific catalyst identification is supplied by this page. These are historical specification claims, not authorization to fuel or run hardware.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and remaining component dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later fuel and catalytic oil restrictions.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later fuel and catalytic oil restrictions, PDF pages 1, 3, 4, 5
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later idle-stall and load-loss diagnosis
Idle stalling and load-related power loss have multiple fuel-system causes; L, H and LA remedies are variant-specific, not LD instructions.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 4.2, printed 8 / PDF9: engine stalls at idle — blocked idle jet bores/ports: clean and blow clear with compressed air; idle mixture too rich or lean: reset low-speed screw L correctly; incorrect LA setting with throttle shutter completely closed: reset LA correctly. No compressed-air pressure or new numeric setting is given.
- Engine speed drops quickly under load / low power — plugged filter: clean or replace as necessary; faulty tank vent: fit new vent; leak between tank and fuel pump: seal or renew connections and fuel line; damaged/fatigued pump diaphragm: fit new diaphragm.
- The same load-loss condition also lists blocked main jet bores/ports: clean them; dirty pickup body: install new pickup; H too rich: reset H correctly; throttle not fully opening: check linkage. These are alternatives, not a mandatory sequence of replacing all components.
- The L/H/LA labels apply only where that carburetor arrangement exists. They must not be transferred to the left-hand LD balanced-idle system; the separate reviewed section9.4 variant procedures retain their limits. Generic clean-filter wording does not override the felt/multi-ply no-wash rule or foam distinctions in9.1.1. Pickup replacement is not blanket permission to wash the old pickup.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and separate handbook dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later idle-stall and load-loss diagnosis.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later idle-stall and load-loss diagnosis, PDF pages 1, 3, 4, 9
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later poor-acceleration diagnosis
Poor-acceleration rows retain capped L/H adjustment stops and the carburetor-body lever reference without assigning those screws to every variant.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 4.2 continuation, printed 9 / PDF10: idle jet too lean — turn L counterclockwise (richer), no further than stop; main jet too lean — turn H counterclockwise (richer), no further than stop. These are the printed L/H directions, not the left-hand LD procedure. No cap removal, forced stop or universal turn count is authorized by these rows.
- Inlet control lever too low relative to correct installed position — set it flush with the top of the carburetor body. Inlet needle sticking to valve seat — remove, clean and refit. Blocked connecting bore to atmosphere — clean the bore. Leaking diaphragm gasket — fit new gasket. Damaged or shrunken metering diaphragm — fit new diaphragm.
- The reference is the top of the carburetor body, not the gasket surface. No bending method, numerical gauge clearance, solvent or air-pressure value is stated in this table. The separate metering/pump stack orders and needle/spring assembly precautions remain applicable. Seven possible cause/remedy rows are retained; poor acceleration alone does not prove any one cause.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and separate handbook dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later poor-acceleration diagnosis.
Later manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later poor-acceleration diagnosis, PDF pages 1, 3, 4, 10
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: later high-idle and flooding table conflict
The flooding table literally lists an inlet lever “too low” and says replace it; the separate poor-acceleration row says set a low lever flush.
- Later component evidence: January 2005, not a contemporaneous 1999 instruction or proof of original equipment. The introduction covers BG 45/46/55/65/85 and SH 55/85; this TI29-linked note is limited to BG 55/65/85 and SH 55/85 and the explicitly stated component variants. Catalog assembly links are navigation, not proof that all revisions fit.
- Section 4.2 continuation, printed 9 / PDF10: engine will not idle / idle speed too high — throttle shutter opened too far by LA: reset LA correctly. This LA row is not a left-hand LD setting and supplies no numeric idle speed.
- Carburetor floods / engine stalls — inlet needle not sealing due to foreign matter in the valve seat or damaged cone: remove and clean or replace the needle; clean tank, pickup body and fuel line if necessary. The same condition lists lever sticking on spindle: free it; helical spring off the lever nipple: remove lever and refit correctly.
- A deformed perforated disc pressing continuously against the inlet lever calls for a new metering diaphragm. The final flooding row literally says inlet control lever too low (relative to correct installed position), with remedy fit new inlet control lever. Preserve that unexpected cause/remedy pairing; do not silently change low to high.
- The poor-acceleration row on the same page instead says set a low lever flush with the top of the carburetor body; section9.3.4 also specifies that flush reference. This unresolved diagnostic discrepancy does not establish a different flood height, a bend-up remedy or a new numerical setting. The conditional pickup-cleaning wording here remains distinct from the load-loss row that replaces a dirty pickup.
- The recovered copyright1999 Carburetors handbook section6 PDF23 explicitly says too high and set flush, not too low and replace. Its section7.5 PDF28 separately replaces an off-level bent lever. See the handbook-diagnosis note for the cross-source comparison; the later2005 wording above remains unchanged and unresolved.
- The component manual requires the instruction manual safety precautions and applicable local regulations for any engine run. Fuel work is outdoors only, away from fire, flame, sparks or heat; wipe up spilled fuel immediately. These are source-reviewed reference notes, not a complete repair instruction or hardware verification. Exact owner-manual and separate handbook dependencies stay open.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 component dependency; January2005 later high-idle and flooding table conflict.
Manual evidence: STIHL Series 4140 Components BG, SH service manual (2005-01), section later high-idle and flooding table conflict, PDF pages 1, 3, 4, 10 · Carburetors (publication revision unestablished; ©1999), section Cross-source flooding and lever-remedy discrepancy:6 and7.5, PDF pages 1, 2, 23, 28
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: how balanced-idle bypass flow changes with LD
Handbook explains bypass-air control, equal-pressure zero flow and reversal toward the engine. Copyright 1999; exact edition unknown.
- TI29/1999 explicitly identifies a balanced idle system and delegates its detailed description to the Carburetors handbook of November 1998 or later. The recovered owner-collection PDF is titled Carburetors, not a 021/023/025 or MS210/230/250 machine manual despite its filename. Its contents page has copyright 1999, but an exact edition date is not established. This is supplementary functional evidence, not proof that it is the precise edition cited by the TI or proof of original carburetor identity.
- Section5.2.4 describes a fixed idle jet and calibrated air bypass system. The throttle shutter is completely closed at idle. Most idle-mixture air goes through the hole in the shutter; the additional air used to adjust idle speed is controlled by the single LD screw through the bypass/idle chambers. This is not the separate primary-mixture-control system in section5.2.3 or a conventional H/L mixture-screw adjustment.
- At low idle, LD restricts the bypass port. Engine-side vacuum Pu behind shutter7 draws air through hole8 and produces pressure P3 in idle chamber3 via primary idle bore6, and P11 in bypass chamber11 via bypass port10. When P11 is below upstream atmospheric pressure, air enters chamber11 through port9. When P11 is above P3, air flows from chamber11 through connecting passage4 to idle chamber3.
- Idle chamber3 also receives air through secondary idle bore5 and fuel from metering-diaphragm chamber1 through fixed idle jet2. Its primary mixture passes through primary idle bore6 to the engine side of the shutter. That mixture combines with air from bypass port10 and shutter hole8 to form the idle mixture. The numbered features are functional diagram labels, not orderable part numbers.
- Clockwise LD rotation increases idle speed; counterclockwise reduces it. The handbook explicitly explains that LD has a left-hand thread. Clockwise rotation lowers P11, increases throughput at port10 and reduces the pressure difference between P3 and P11, so less air flows through passage4 toward the idle chamber. On PDF16, passage4 flow stops when P3 equals P11. Further clockwise rotation makes P11 lower than P3, reversing flow: primary mixture from chamber3 passes through passage4 into the bypass air flowing through ports9 and10. Do not describe that reversal as a fault or reverse the LD directions.
- The handbook claims smooth idle, good acceleration, lower emissions, stable adjustment across ambient temperatures and simpler single-screw adjustment. These are source claims, not measured performance here. Its lambda/CO-versus-rpm graphic labels 2500,2800,3100 but supplies no numerical lambda/CO values in the reviewed rendering; do not derive emissions limits, adjustment targets or a calibrated curve from it. TI29 supplies the separately admitted historical idle range and two-turn setting. No further number of turns, pressure value or engine test is established by these functional diagrams.
- The adjacent section5.2.5 part-load discussion and limbing example on PDF16 are a separate general-carburetor section, not a BG/SH-specific part-load-jet assignment. No particular Walbro/Zama/Tillotson unit, jet drilling, supersession or interchange follows from this explanation. Coverage is limited to the TI29 BG55/65/85 and SH55/85 balanced-idle description, not BG45/46, BR45C, an SH65 or every later carburetor on the shared IPL.
- Handbook safety/introduction requires the applicable owner manual and local/national precautions, no smoking/flames near fuel, outdoor fuel work, immediate spill cleanup and care around unguarded cutting equipment; it points to the current IPL and later TIs for changes. This functional note performs no hardware operation and does not substitute for the unavailable exact owner manual or unverified exact handbook edition; located service sections are now separately reviewed.
TI dependency: TI 29/1999, p. 2 — TI section1 detailed balanced-idle handbook dependency; Carburetors section5.2.4 including continuation on PDF16.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section Contents/copyright; safety/introduction;5.2.4 balanced-idle system, including PDF16 left-column continuation, PDF pages 1, 2, 15, 16
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: handbook diagnosis and conflicting lever heights
Generic chart distinguishes LD from LA/H/L and says flooding lever too high; later component manual says too low. Neither source is silently corrected.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- PDF23 flooding/stalling rows pair a leaking inlet needle (foreign matter or damaged cone) with cleaning or replacing it and, if necessary, cleaning tank, pickup body and fuel line; a sticking lever with freeing it; a spring off the lever nipple with correct refitting; and a deformed diaphragm disc constantly pressing the lever with a new metering diaphragm.
- The final flooding row says inlet control lever too high relative to design position and set it flush with the top of the body or bottom of the metering chamber. January2005 RA_295 section4.2 PDF10 instead says too low and fit a new lever. Both source statements remain unresolved. The handbook itself also says in7.5 PDF28 that an off-level lever is bent and must be replaced, whereas its table says set flush. No bending instruction, universal height, correction to either source or verified diagnosis is inferred.
- PDF23 poor acceleration: lean idle/main jets are paired with backing off the low/high speed screw slightly; low lever with setting it flush to the design-dependent reference; sticking needle with removing, cleaning and refitting; blocked atmospheric connecting bore with cleaning; leaking diaphragm gasket with replacement; damaged/shrunken metering diaphragm with replacement. H/L adjustments only apply where those screws exist, never as instructions for the single left-hand LD balanced-idle system.
- PDF24 high idle separately lists a throttle shutter held open by the idle screw, LD opened too far, LA opened too far, and machine leakage. The remedies are the matching screw adjustment or locating and repairing the leak. Idle stalling separately lists blocked idle bores/ports (compressed-air cleaning), rich idle jet (low-speed screw slightly in), incorrect idle setting with closed shutter, incorrect LD setting, and a valve-jet plastic plate not closing (clean or renew valve jet). These are distinct carburetor arrangements: a closed shutter is normal in the reviewed balanced-idle description, not a universal fault. No new turn count is given.
- Load-related speed drop/low power: plugged air filter—clean; faulty tank vent—clean or replace as necessary; tank-to-pump fuel-line leakage—seal or renew connections/line; damaged/fatigued pump diaphragm—replace; blocked main bores/ports—clean; dirty pickup—clean pickup and fit new filter; dirty strainers—clean. Generic filter cleaning does not override variant-specific no-wash instructions. The later component table replaces the dirty pickup and vent; preserve the distinct wording, not blanket permission to wash every filter.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 6 troubleshooting, with7.5 lever replacement cross-check.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 6 troubleshooting, with7.5 lever replacement cross-check, PDF pages 1, 2, 23, 24, 28 · STIHL Series 4140 Components BG, SH service manual (2005-01), section later high-idle and flooding table conflict, PDF pages 1, 3, 4, 10
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: wet and dry carburetor test limits
Handbook adds a 0.35-bar dry limit, wet preparation and 1-bar ceiling to the approximately 0.8-bar leakage test; cleaning restrictions remain explicit.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- PDF25 first checks tester1106 850 2905 for leaks. Its test values apply only after flushing with fuel, with moist diaphragms and fuel-wetted passages/sealing points. A dry carburetor must not see more than0.35 bar (5 psi); flush it before the test. The applied test pressure must not exceed1 bar (14.5 psi): the text warns that higher pressure opens the control valve and may overstretch the metering diaphragm.
- The historical setup connects fuel line1110 141 8600 and nipple0000 855 9200 to the intake fitting and tester hose, closes the bulb vent, and pumps to approximately0.8 bar (11.6 psi). Constant pressure is the printed airtight criterion; no hold time or allowable decay is supplied. These are carburetor values, not crankcase settings and not a resolution of the separate tenfold powerhead-unit conflicts. PDF65 corroborates the three tool identifiers; they are test equipment, not fitted replacement hoses.
- Falling pressure suggests a leaking inlet needle, foreign matter, damaged sealing cone or sticking lever; inspect the metering diaphragm for distortion and replace if necessary. Service the carburetor in these cases. Open the vent screw before removing the test line. This fault list does not make a pressure drop a unique diagnosis.
- Section7.2 explains that blocked jets, bores and strainers, and even water droplets restricting fine passages, can cause trouble; freezing water may fully block passages. For cleaning, strip the carburetor and remove adjusting screws, jets and inlet needle as applicable; the page specifies a brush or clean leather cloth with fresh fuel for the body, then compressed air through ports/jets. It forbids needles, wires, similar tools and fibrous cloths for cleaning. No air pressure is supplied.
- Section8.2 PDF65 separately lists white spirit for cleaning all components and medium-strength Loctite242,0786 111 1101, for control valve, sealing plug/plate and throttle/choke-shutter screws. Preserve the fresh-fuel versus white-spirit wording; no chemical equivalence or current substitute is established. Puller5910 890 4500 is expressly only for limiter caps; screwdrivers5910 890 2305 or000 890 2300 are listed for installing adjusting screws/adjustment. These generic tools do not establish that the TI29 carburetor has limiter caps or any particular threadlocker application.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 7.1 leakage test,7.2 cleaning and8 tools/aids.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 7.1 leakage test,7.2 cleaning and8 tools/aids, PDF pages 1, 2, 25, 65
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: handbook diaphragm stacks and wording conflict
Pump and metering stacks differ; a pump-diaphragm caption appears inside the metering section. Keep the original wording and design variants visible.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- PDF26 pump side: remove screws/end cover and carefully separate stuck gasket and diaphragm. Inspect both, replacing as needed; fatigue causes distortion and swelling. Assembly explicitly places gasket on the end cover, wets the pump diaphragm with fuel, and places it on the gasket, then fits the cover to the body. Cast cover pegs locate the stack. Tighten screws securely; no numeric torque is given.
- PDF26–27 metering side: remove cover, diaphragm and gasket carefully; a manual-fuel-pump version delegates cover removal to7.9, now reviewed separately in the manual-pump/check-valve note. Inspect and replace as needed, including fatigue/distortion/swelling. For body pegs, gasket goes on the body and metering diaphragm on the gasket. This is not the pump-side order.
- Within7.4, PDF27 figure915RA045 shows the perforated plate pointing toward the inlet control lever. Its caption literally says Fit pump diaphragm despite the surrounding metering-diaphragm heading and steps. Retain this terminology discrepancy; do not silently rewrite the source or substitute a fuel-pump diaphragm on that basis.
- If the locating peg is on the end cover, PDF27 instead places metering diaphragm2 and gasket3 on that cover; the drawing retains the gasket on the body side. For a carburetor with compensator, install the end cover with connector. These conditional designs do not identify the unnamed1999 carburetor, establish a compensator on it or give a replacement diaphragm number. Fit the cover and tighten screws securely, with no numeric torque supplied.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 7.3 pump diaphragm and7.4 metering diaphragm.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 7.3 pump diaphragm and7.4 metering diaphragm, PDF pages 1, 2, 26, 27, 30
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: handbook needle, lever and main-jet boundaries
Needle wear is distinct from its engagement groove; lever references depend on design, and the WS-26A jet-removal exception is not assigned to these models.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- After removing the metering diaphragm, remove the retaining screw and the lever/spindle or plate/lever/gasket arrangement, then pull the needle. PDF27 requires replacing a needle whose sealing cone has an annular indentation because it no longer seals properly. This wear mark is not the annular groove on the needle head used to engage the lever clevis.
- PDF28 inserts the needle, spring in the blind hole, spindle in the lever and clevis in the needle-head groove; press the lever down and secure with the screw. The spring must locate on the lever nipple and the lever move easily. The lever top is level with either the bottom of the metering chamber or the top face of the body, according to the illustrated design. These are alternatives, not two simultaneous datums. An off-level lever is described as bent and must be replaced; no bend-to-adjust method or numeric clearance is supplied.
- The handbook troubleshooting table23 instead says set the lever flush for both too-high flooding and too-low acceleration. Its replacement instruction here and the later2005 conflicting flooding row remain separately recorded; no generic table authorizes bending or identifies the correct carburetor variant.
- Section7.6: if the check-valve plate in the main jet no longer moves freely, install a new main jet. After metering-diaphragm removal, the general illustrated method presses the jet out toward the venturi with a suitable pin punch; wash it in white spirit, install exactly vertically and press flush with the metering-chamber bottom. The text specifies no punch size, pressing force, jet number or permission to enlarge a bore.
- The separate WS-26A exception pushes the valve jet out with a screwdriver from inside the venturi. The assignment roster provides no exact TI29 model row; this named exception is not assigned to BG55/65/85 or SH55/85. General main-jet service is supplementary context, not proof of a replaceable jet on every TI29 unit or permission to transfer the method to a fixed idle jet. Exact model/variant binding is required.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 7.5 inlet needle and7.6 main jet.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 7.5 inlet needle and7.6 main jet, PDF pages 1, 2, 27, 28
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: fixed-jet service boundaries
The illustrated part-load fixed jet is not replaceable; full-load jet methods differ by carburetor. Named exceptions do not identify TI29 fitment.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- PDF29 section7.7 removes the metering diaphragm first. Its illustrated part-load fixed jet1 cannot be replaced and can only be blown clear with compressed air. The illustrated full-load fixed jet2 is pressed out toward the venturi with a pin punch. These are distinct jets: the full-load removal method must not be applied to the nonreplaceable part-load jet or silently equated with the balanced-idle fixed jet.
- The full-load jet is washed in white spirit and blown out with compressed air; replace a damaged jet. The general illustrated installation is exactly vertical, pressed flush with the bottom of the metering chamber. No jet size, punch diameter, air pressure or pressing force is supplied. This conditional design does not establish a removable full-load jet on every TI29 unit.
- The HS-262B exception unscrews the full-load jet. The HD-5 exception removes a retaining ring, taps the body on a wooden base to release jet and O-ring, then uses a new O-ring and installs the jet flat side up to its stop, secured by the retaining ring. Those named methods are not assigned to BG55/65/85 or SH55/85: the reviewed assignment roster has no exact row for them. Refit the metering diaphragm after the applicable method.
- Adjacent7.8 applies expressly to WT-227E and WT-264: manual-pump removal, control valve and copper washer replacement, about two initial turns, Loctite on the projecting thread, then seating to the stop and4 Nm (3.0 lbf.ft). This is retained solely as an excluded named-carburetor boundary, not a TI29 torque, fitted valve or general carburetor instruction. No exact TI29 binding was found in the roster.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 7.7 full-load/part-load fixed jets;7.8 named-only control-valve boundary.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 7.7 full-load/part-load fixed jets;7.8 named-only control-valve boundary, PDF pages 1, 2, 29
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: manual pump and check-valve service
The flange valve and separate check-valve operation are distinct; pump-cover access completes the diaphragm note without assuming every variant has this design.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- Section7.9 removes the cover screws, end cover with pump bulb, bulb, flange and valve from the flange in that order. Inspect the valve and replace as necessary. A malfunctioning circuit for filling the metering chamber, or a dirty, distorted or damaged valve, calls for a new valve. Inspect metering diaphragm and sealing ring and replace if needed under7.4; assemble in reverse order. No fitted bulb or valve part number, numeric screw torque or universal variant assignment is supplied.
- This is the manual-pump cover-access dependency from the handbook diaphragm note. It does not reverse that note's metering gasket/diaphragm stack, resolve its literal pump-diaphragm caption or establish that all TI29 variants have the illustrated pump flange.
- Adjacent7.10 is a separate check-valve operation after metering-diaphragm removal: fit a2.5x13 mm self-tapping screw into the valve bore and use it to pull the valve out. The screw is a removal aid, not a replacement component left in the carburetor. Press the check valve squarely into the metering chamber to the stop with a4 mm (approximately5/32 inch) pin punch; then refit the metering diaphragm.
- The illustrated flange valve in7.9 and the press-fit check valve in7.10 must not be conflated. The body section7.11 expressly conditions check-valve removal on its being fitted. No bore enlargement, drilling, pressing force, replacement valve number or proof of this construction on an unnamed TI29 carburetor is inferred.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 7.9 manual fuel pump and7.10 check valve.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 7.9 manual fuel pump and7.10 check valve, PDF pages 1, 2, 30
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: carburetor body, strainer and sealing plugs
Body service preserves the left-hand LD thread and replacement-only sealing plugs; H/L screw removal is not transferred to a single-LD design.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- PDF31 first removes pump diaphragm, inlet needle and valve jet through7.3/7.5/7.6; full-load fixed jet and check valve are removed only if fitted, through7.7/7.10. Pry the fuel strainer out with a scriber and clean it; always replace a damaged strainer. This extraction aid is not permission to clear jets with a scriber or wire, prohibited by7.2.
- The illustrated high-speed and low-speed screws and, if fitted, idle-speed screw are removed as applicable. The separate warning says idle-speed screw LD has a left-hand thread. H/L removal is not applicable to a carburetor that has only LD, and this section supplies no basic adjustment turn count.
- Press the center of the sealing plug or plate with a pin punch until it buckles and can be removed. The source explicitly says removal destroys the plug or plate. A removed plug is not reusable. Wash the body in fresh white spirit and blow ports and bores clear with compressed air. No air pressure is specified; this does not erase the fresh-fuel cleaning wording in7.2.
- For body replacement, remove throttle shaft and choke shaft if fitted through7.12/7.13. Install a new sealing plug or plate convex side up; use a large pin punch with light pressure until flat. Apply Loctite under8.2 to the gap between body and plug/plate, then assemble remaining parts in reverse order. No plug diameter, pressing force, body replacement part number or universal Loctite application is established.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 7.11 carburetor body.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 7.11 carburetor body, PDF pages 1, 2, 31
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: throttle and choke shaft design differences
Shaft service keeps retaining hardware, spring and ball-detent variants distinct. Named lever orientations and automatic-choke settings are not TI29 specifications.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- Section7.12 PDF32–33 removes the shutter screw and shutter, E-clip and washer if fitted; some designs also need lever screw/lever, spacer sleeve or screw-retained clip removal. Withdraw the throttle shaft carefully and check excessive play as a possible source of secondary air. Some carburetors require pump-cover removal first. Remove its torsion spring; a slotted-pin arrangement also has a pin-retaining E-clip and removable pin. These are alternatives, not a combined parts stack for every model.
- After refitting the throttle shaft, check the torsion spring position. The spring illustration is expressly WT-227F; similar positioning on other carburetors is not exact fitment evidence. Seat the throttle shutter with its whole circumference against the venturi wall, use Loctite under8.2 on the screw and tighten securely; no numeric torque is given. Refit the applicable groove-mounted E-clip or screw-retained clip.
- Named arrangements remain separate: C1Q-S11G detaches/attaches the torsion spring to the throttle-shaft groove; WT-230 uses a spacer sleeve and slotted pin toward the metering cover; HD-3A uses a sleeve and slotted pin toward the intake fitting; WT-253 points the lever toward the intake fitting; C1Q-SK6 points the slotted pin toward the metering cover. None is assigned to TI29 BG55/65/85 or SH55/85 without exact binding.
- Section7.13 PDF34–35 removes lever if fitted, shutter screw/shutter and E-clip if fitted. A shaft with torsion spring is withdrawn with that spring; remove/refit it and check positioning. A shaft without torsion spring is withdrawn carefully so the ball is not lost, then ball and spring are removed. Refit spring and ball and insert the shaft until the ball engages its groove. Seat the choke shutter around the venturi wall, use Loctite under8.2 on its screw and tighten securely; fit the E-clip on the torsion-spring design and refit the lever if removed. No numeric torque is given.
- The C1Q-S11G captions within the choke-shaft section still explicitly refer to the throttle shaft for detaching/attaching the torsion spring. Retain that cross-shaft wording and named restriction; do not silently rewrite it as choke shaft or treat it as proof of an error.
- Section7.14 PDF35 applies only to a carburetor with accelerator pump: after throttle-shaft removal, remove piston and spring, inspect both, renew the piston sealing ring, put spring in bore and piston closed end outward, then depress piston to refit the throttle shaft. This feature is not established for TI29 by the reviewed roster. It is an excluded feature boundary, not a TI29 pump specification or instructions to modify a carburetor.
- Sections7.15–7.15.1 PDF36–38 apply only to automatic choke and a longer throttle shaft, with a specific A–I lever system, supported pressing against buckling, spring orientation and functional check. The printed idle-position statement has choke closed and throttle37 degrees to the mounting face; opening the choke should make the throttle jump closed just before full choke opening, with a click. These are not transferred to TI29's balanced-idle system or corrected to an assumed normal running-idle position. No automatic-choke fitment, universal37-degree setting or replacement linkage is established. Adjacent7.16 begins a separately named-carburetor section and is not closed by this review.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 7.12 throttle shaft,7.13 choke shaft;7.14–7.15.1 feature boundaries.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 7.12 throttle shaft,7.13 choke shaft;7.14–7.15.1 feature boundaries, PDF pages 1, 2, 32, 33, 34, 35, 36, 37, 38
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: carburetor identification and mixture context
Cast family marks and stamped designations are not interchangeable identities. The handbook mixture examples explain operation, not TI29 adjustment targets.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- Section3.1 distinguishes stamped or printed designations (illustrated HT-7A and WT-223), cast family marks (C3M or HD), and further stamped or printed identification numbers (S20 or S36C). A family mark alone does not establish the complete carburetor variant. These are identification examples, not assignments to TI29 models or replacement part numbers.
- Section4 describes atomization in the carburetor and complete vaporization only upon reaching the combustion chamber. Heat taken from the components during vaporization provides internal cooling. Its ideal-mixture example is lambda1 at14.8 kg air to1 kg fuel, with a stated combustible range lambda0.7–1.25. These are handbook explanatory figures, not oil-to-fuel ratios, a TI29 tuning range or permission to operate at either endpoint.
- The handbook distinguishes a lean mixture with more air, reduced power, overheating and inadequate oil-bearing fresh charge with seizure risk, from a rich mixture with less air and incomplete combustion, including exhaust smoke. Conditions such as temperature, humidity, air pressure and operating phase change the required mixture. No TI29 measured lambda, emissions, oil ratio, jet identity or adjustment setting is established.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 3.1 designation and4 purpose.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 3.1 designation and4 purpose, PDF pages 1, 2, 8
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: impulse pump, metering and manual purge flow
The impulse pump, demand-controlled inlet needle and optional manual pump have separate functions. Pressing the illustrated bulb returns fuel to the tank.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- The handbook describes an all-position diaphragm carburetor without a float. Its integrated fuel pump operates as a separate unit, driven through the impulse port by crankcase pressure changes. On the piston upstroke, low pressure flexes the diaphragm and atmospheric tank pressure pushes fuel through the intake fitting and inlet flap; the outlet flap closes. On the downstroke, overpressure reduces fuel-chamber volume, closes the inlet flap and opens the outlet flap toward the carburetor inlet valve. Both flaps are formed from the pump diaphragm. No measured delivery volume, impulse pressure or TI29 hose routing is supplied.
- Fuel drawn from the metering chamber lets external pressure move the metering diaphragm against the inlet lever, lifting the inlet needle. Fuel enters until chamber pressure is approximately equal to the pressure outside the diaphragm. Normally that reference is atmospheric pressure through a bore; if a compensator is fitted it is the clean side of the air filter. PDF10 literally refers to chapter4.3.4 for the compensator; preserve that printed cross-reference rather than silently treating it as a verified section locator. Compensator functional context is reviewed separately under its actual5.3.4 heading; the printed4.3.4 reference remains uncorrected.
- A tank below the carburetor may require priming after prolonged non-use. The optional manual pump fills the system before starting; the handbook explicitly distinguishes a separate chainsaw pump from the illustrated integrated arrangement. Pressing the bulb opens its valve and returns air or fuel to the tank. Releasing it creates metering-chamber vacuum, pulls the metering diaphragm against the lever, opens the inlet needle and draws fuel from the pump chamber. Excess fuel passes through the bore and valve tabs into the bulb, then returns to the tank on the next press. This is not an instruction to inject fuel directly into the venturi, nor a specified number of presses.
- PDF11 says carburetors with the additional manual pump have a metering-chamber check valve. It closes during manual pumping to stop air entering from the venturi and idle bores, then opens during operation to supply main and idle jets. The separate main-jet check valve in5.2.1 prevents air entry at idle. Neither illustration establishes that all TI29 variants have the optional pump, compensator or same valve construction. No valve part identity, universal retrofit or pressure setting is inferred.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 5 construction and5.1 fuel pump, inlet needle, manual pump and check valve.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 5 construction and5.1 fuel pump, inlet needle, manual pump and check valve, PDF pages 1, 2, 9, 10, 11, 20, 21
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: full-load and idle circuit distinctions
Fixed, semi-fixed and adjustable fuel circuits are separate designs. Generic L/H and primary-mixture examples must not replace TI29 balanced-idle instructions.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- At full load the throttle is wide open and both main and idle jets deliver fuel. The illustrated main jet lies at the narrowest venturi section, with highest air speed and lowest pressure; its check valve prevents air entry into the metering chamber at idle. An adjustable main circuit uses H. In the semi-fixed design, a defined fuel portion bypasses H through the semi-fixed jet to the main jet, reducing adjustment sensitivity. The source example is approximately80% at H=1, not a TI29 setting or measured flow result.
- A full-load fixed-jet design passes all full-load fuel through that jet and has no H adjustment. Both fixed and semi-fixed jets may be separate components or nozzle bores integrated in the main jet; a separate jet connects to the main jet by a passage, not directly to the venturi. No full-load fixed jet, part-load fixed jet or BIS fixed jet is silently equated with another, and no size or replacement identity is supplied.
- Section5.2.2 describes conventional idle with the throttle almost closed and primary-idle fuel delivered at its gap; the slight vacuum at the main jet draws no fuel. Two or three idle bores are possible. In the illustrated three-bore design, air initially enters through the two upstream bypass bores and mixes with fuel in the idle chamber; opening the throttle puts those bores under vacuum so they also deliver fuel for acceleration. L varies flow to the idle chamber. These conventional throttle-stop and L controls are not TI29 BIS LD directions.
- The handbook calls parallel main and idle circuits an idle system independent of the main jet system, but says changing L changes total full-load fuel and requires H readjustment. Leaning idle also leans the overall mixture and increases overheating risk. In the separately illustrated dependent system, idle branches after H and is not directly connected to the metering chamber; H determines full-load volume, and changing L does not change overall volume. Preserve these source labels and their different consequences; do not infer which design is fitted from the word independent alone.
- Section5.2.3 is a distinct fixed-idle-jet / primary-mixture-control design, not the adjacent5.2.4 balanced-idle system. It supplies primary mixture through a fixed idle jet and three idle bores, with air through a throttle notch or hole. Its approximately1-turn basic opening, richer when opening / leaner when closing, separate LA speed screw and main-jet delivery at about20 degrees throttle opening belong only to this illustrated design. They are not transferred to TI29 LD or treated as universal adjustment values.
- That primary-mixture design limits acceleration enrichment and idle-circuit flow at full load through the fixed idle jet, so its idle-screw setting does not change full-load fuel volume. The handbook attributes steadier low-temperature idle to the round fixed-jet orifice compared with the annular adjusting-screw gap as fuel becomes viscous. These are source explanations, not measured TI29 cold performance or permission to modify an orifice. The already reviewed balanced-idle flow note retains its own left-hand LD directions.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 5.2.1 full load,5.2.2 idle and5.2.3 fixed idle jet with primary mixture control.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 5.2.1 full load,5.2.2 idle and5.2.3 fixed idle jet with primary mixture control, PDF pages 1, 2, 11, 12, 13, 14
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: part-load, starting and cold-weather boundaries
Part-load enrichment and starting explain different fuel demands. Automatic choke, heating and accelerator-pump examples do not establish TI29 equipment.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- Section5.2.5 describes a partly open throttle drawing fuel from primary and secondary idle jets. An illustrated part-load fixed jet opens between idle and main jets and supplies additional fuel under low pressure to avoid an over-lean part-load flat spot and seizure risk. No TI29 part-load jet identity, diameter or universal retrofit is established; the adjacent balanced-idle continuation is already covered separately.
- Section5.3.1 explains that cranking produces much less venturi speed and vacuum than running idle and that fuel responds more slowly than air. Cold surfaces add poor vaporization and condensation. The illustrated cold start closes the choke to enrich the mixture, then opens it once the engine fires/runs to avoid an over-rich stall as deposited fuel evaporates. This is functional context, not an exact TI29 start-control sequence, permission to close choke for every hot start or a substitute for the owner manual.
- The optional automatic choke uses cylinder temperature, crankcase pressure waves, a control valve, bellows and linkage. The source gives opening periods from3.5 seconds cold to approximately0.1 seconds hot. PDF18 places the throttle at37 degrees to the mounting flange just before the choke opens fully, returning to idle when fully open. This differs in wording and operating position from7.15 service text calling the closed-choke/37-degree position idle. Both descriptions remain attributed; neither is silently corrected or adopted as a TI29 setting.
- After an automatic-choke start attempt the bellows refill from the carburetor box through foam and polymer-sintered filters, hose and control valve, with a low whistle; during running they remain contracted and the choke open. This complete feature context does not establish automatic-choke equipment on TI29 models, a diagnostic time tolerance or permission to alter linkage.
- Section5.3.2 says intake icing can occur at high humidity below+10 C (50 F), not only below freezing: intake pressure/temperature drops can condense moisture and form ice that blocks jets. Its optional electric heater on mounting studs, pump-cover thermostatic switch and generator supply are feature-specific examples. No TI29 heater fitment, switching threshold or winter-setting instruction is inferred from the icing temperature.
- Sections5.3.3 PDF19–20 describe an optional accelerator pump whose throttle-shaft control face pushes a spring-loaded piston inward, sending fuel through the valve jet into the venturi during acceleration. Returning the throttle lets the spring restore the piston and draws fresh fuel from the metering system. This offsets delayed fuel response relative to air. It is distinct from the manual purge pump and impulse pump, and is not proof of a TI29 accelerator pump, fuel dose or fitted component.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 5.2.5 part load and5.3.1–5.3.3 starting, temperature/humidity and acceleration.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 5.2.5 part load and5.3.1–5.3.3 starting, temperature/humidity and acceleration, PDF pages 1, 2, 16, 17, 18, 19, 20
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: compensator limits and governor boundaries
A compensator follows clean-side filter pressure; it does not restore lost airflow or power. Separate governor examples are not TI29 speed settings.
- Supplementary generic handbook evidence, copyright1999 with exact edition unknown, for the TI29 BG55/65/85 and SH55/85 service dependency. The complete assignment roster has no exact row for these models. This is not proof of the original carburetor, universal component fitment or a substitute for exact variant instructions; other BG/SH models on shared IPL pages are excluded.
- Section5.3.4 identifies Pa as atmospheric pressure, Pi as internal intake pressure and Pr as metering-chamber pressure. The compensator connects the clean side of the air filter to the metering system, applying Pi rather than Pa outside the diaphragm. A dirty filter reduces airflow and Pi; the diaphragm moves outward and the inlet valve reduces fuel flow so the mixture does not become over-rich. This reviews the actual5.3.4 section without silently replacing PDF10's literal4.3.4 reference.
- The handbook claims constant mixture fuel content despite filter contamination and no H readjustment as contamination increases, but expressly says power falls and cleaning the filter is necessary to restore normal power. It also says no further adjustment is needed after cleaning or when converting between its HD textile and standard wire-mesh filters. These statements are conditional on the described compensator system; they do not establish TI29 filter interchange, fitted compensator or an exemption from filter maintenance and variant instructions.
- The schematic power curves label clean filter, dirty filter with compensator and dirty filter without compensator. They have no numerical power or rpm scale; no percentage power loss, rpm limit or measured TI29 performance is inferred.
- Section5.4 separately describes a control valve that may occur on carburetors directly flange-mounted to the cylinder without a resilient manifold. Resonance at a predetermined speed opens it to draw extra fuel and limit speed by enrichment. No opening speed, part identity or assignment to TI29 is supplied; this is not the metering inlet needle or a universal limiter.
- PDF22 separately describes a cooling-air vane governor: airflow overcomes torsion-spring tension and moves linkage to close the choke enough to enrich and limit rpm. The source says cutoff speed can be adjusted by spring preload but supplies no numerical setting. This unbound feature is excluded from TI29 application; no permission or procedure to change TI29 spring preload or governed speed is inferred.
- These are source-reviewed reference notes, not a performed test or complete bench procedure. Applicable owner-manual precautions, outdoor fuel work away from ignition sources and spill cleanup remain required. No hardware operation, part interchange or repair success is established.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 service dependency; Carburetors 5.3.4 dirty air filter/compensator and5.4 special features.
Manual evidence: Carburetors (publication revision unestablished; ©1999), section 5.3.4 dirty air filter/compensator and5.4 special features, PDF pages 1, 2, 20, 21, 22
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: February2018 USA carburetor table boundaries
USA rows separate BG55/SH55/BG65 from BG85/SH85. Listed carburetors and blank cells are not original1999 fitted identities.
- Later February2018 reference evidence only, not proof of the carburetor fitted in1999, a serial changeover, universal interchange or a replacement for the exact owner/service manual. The worldwide row also names BG50, but these TI29 notes cover only BG55/65/85 and SH55/85. BG45/46, BR45/46 and later BG56/66 rows are excluded despite adjacent or shared catalog headings.
- DT_USA PDF24 and the USA section of DT_Weltweit PDF74 show identical reviewed page images. Both say2018-02 USA and footer0456 400 3006 B18 FD. This establishes equivalence of these rendered pages only, not whole-PDF identity or worldwide equivalence.
- The USA BG55,SH55,BG65 group lists C1Q-S55 on its first subrow, with dashes in the H/L cap and setting cells. The next subrow lists C1Q-S64, C1Q-S68 and C1Q-S68E, with an H-cap pictogram and an L dash. The BG85,SH85 group instead has a dash in the first carburetor cell and lists only C1Q-S64 and C1Q-S68 in its second subrow. Do not fill that dash with C1Q-S55 or transfer C1Q-S68E to BG85/SH85 from the adjacent group.
- For both USA adjustable subrows, the first H/L setting pair is1 1/2 (24/16) and1 (16/16); the second is3/4 (12/16) and1 (16/16). The header distinguishes an uncapped/crossed-cap screw pair from a capped screw pair and labels H/L beneath each; these are separate pictogram-defined columns, not four settings to apply in sequence. No prose key establishing the full setting procedure was located in the extracted table text or named installer PDF inventory. Preserve that interpretation limit instead of converting the values into an unconditional tuning instruction.
- The table supplies no LD value for these C1Q-S55 rows. Dashes are not zero turns, proof of a missing component or permission to substitute H/L settings for the1999 balanced-idle LD procedure. Earlier BIS flow and direction notes remain unchanged.
- These compact tables do not supply a complete adjustment or fastening procedure. Exact installed carburetor, market, limiter configuration and component instructions must be established before use; no hardware adjustment, limiter removal, physical interchange or repair success is verified.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 dependency follow-up: February2018 regional specification tables, not original1999 assignments.
Later manual evidence: Technical specification tables, USA (2018-02), section Exact series4229 BG/SH rows and complete pictogram headers; USA and worldwide kept separate, PDF pages 24 · Technical specification tables, worldwide including USA (2018-02), section Exact series4229 BG/SH rows and complete pictogram headers; USA and worldwide kept separate, PDF pages 29, 74
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: February2018 worldwide carburetor groups
The worldwide table adds C1Q-S68G and C1Q-100332A, but its grouped row does not assign each carburetor to each model.
- Later February2018 reference evidence only, not proof of the carburetor fitted in1999, a serial changeover, universal interchange or a replacement for the exact owner/service manual. The worldwide row also names BG50, but these TI29 notes cover only BG55/65/85 and SH55/85. BG45/46, BR45/46 and later BG56/66 rows are excluded despite adjacent or shared catalog headings.
- DT_Weltweit PDF29 says2018-02, footer0456 400 9908 B18. Its one series4229 group names BG50,55,65,85 and SH55,85. It is not the USA grouping. No exact one-to-one model/carburetor assignment, market subvariant, serial applicability or production date follows from this shared cell.
- The worldwide group lists C1Q-S55 with dashes across cap/settings cells; then C1Q-S64,C1Q-S68,C1Q-S68E; then C1Q-S68G and C1Q-100332A. For S64/S68/S68E the H cap is pictured and L is dashed. For S68G/100332A both H and L cap pictograms appear. This is later group-level identification evidence, not a replacement roster or proof that every named machine accepts all six carburetors.
- The merged first H/L setting pair is1 1/2 (24/16) and1 (16/16), and the second H value is3/4 (12/16). The second L value is1 (16/16) for C1Q-S64/S68/S68E but3/4 (12/16) for C1Q-S68G/100332A. Original horizontal cell borders retain the shared values and the L subdivision; text extraction alone obscures that relationship. Keep the uncapped/crossed-cap versus capped header distinction and the missing prose-key limitation from the USA note. No cap manipulation or adjustment sequence is inferred.
- The grouped worldwide C1Q-S55 listing does not resolve the USA BG85/SH85 dash. Nor do worldwide S68G/100332A entries establish their USA applicability. Both regional presentations remain attributed without choosing one as the universal configuration.
- These compact tables do not supply a complete adjustment or fastening procedure. Exact installed carburetor, market, limiter configuration and component instructions must be established before use; no hardware adjustment, limiter removal, physical interchange or repair success is verified.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 dependency follow-up: February2018 regional specification tables, not original1999 assignments.
Later manual evidence: Technical specification tables, USA (2018-02), section Exact series4229 BG/SH rows and complete pictogram headers; USA and worldwide kept separate, PDF pages 24 · Technical specification tables, worldwide including USA (2018-02), section Exact series4229 BG/SH rows and complete pictogram headers; USA and worldwide kept separate, PDF pages 29, 74
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · BG 55 / BG 65 / BG 85 / SH 55 / SH 85
BG/SH 55, 65, 85: February2018 shared specifications and symbol limits
Later rows agree on27.2cm³, ignition gap, plugs and2800rpm idle. Torque pictograms retain their limited component context.
- Later February2018 reference evidence only, not proof of the carburetor fitted in1999, a serial changeover, universal interchange or a replacement for the exact owner/service manual. The worldwide row also names BG50, but these TI29 notes cover only BG55/65/85 and SH55/85. BG45/46, BR45/46 and later BG56/66 rows are excluded despite adjacent or shared catalog headings.
- All reviewed exact-model rows give27.2cm³ (USA1.66cu.in), ignition-module/flywheel air gap0.30mm with worldwide tolerance(+0.15/-0.15), Bosch WSR6F / NGK BPMR7A plug listings, electrode gap0.5mm, and nL idle speed2800rpm. USA also prints air gap0.012in with(0.006/-0.006), electrode gap0.02in. The USA positive tolerance lacks a printed plus sign; preserve its literal(0.15/-0.15) instead of claiming identical typography. These are source specifications, not measurements of a present machine.
- The three populated torque columns are9,17,21Nm (USA6.5,12.5,15.5lbf.ft), under cylinder, flywheel and solid-hexagon pictograms respectively. The following outlined-hexagon and final feeler-gauge columns are blank. The source header does not identify thread sizes, fastener reuse, locking teeth, lubrication or all component joints; in particular the21Nm hexagon symbol is not silently renamed spark-plug torque. No blank becomes zero or a maximum speed.
- The1999 powerhead manual separately specifies20Nm for its M14x1.25 spark plug,17Nm starter cup and9Nm engine-pan/cylinder and muffler joints. The2018 icon-only21Nm entry neither overrides that20Nm instruction nor establishes a same-joint contradiction. Preserve component and edition boundaries pending an explicit symbol key/component procedure. Likewise2800rpm is idle, not the7000rpm rated-power speed or a maximum permitted speed.
- No airflow, weight, bore/stroke correction, fuel-mixture ratio, pressure-test value or model-specific carburetor changeover is supplied by these three rows. Earlier stroke-unit, pressure, diaphragm and lever conflicts remain retained. Unrelated adjacent models and other table pages are outside this bounded dependency review, not semantically closed.
- These compact tables do not supply a complete adjustment or fastening procedure. Exact installed carburetor, market, limiter configuration and component instructions must be established before use; no hardware adjustment, limiter removal, physical interchange or repair success is verified.
TI dependency: TI 29/1999, p. 5 — TI29 section5.3 dependency follow-up: February2018 regional specification tables, not original1999 assignments.
Later manual evidence: Technical specification tables, USA (2018-02), section Exact series4229 BG/SH rows and complete pictogram headers; USA and worldwide kept separate, PDF pages 24 · Technical specification tables, worldwide including USA (2018-02), section Exact series4229 BG/SH rows and complete pictogram headers; USA and worldwide kept separate, PDF pages 29, 74
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the SH 55, SH 85? Report a correction →