Stihl 4237 · Section F · 6 of 14 · 35 parts
Carburetor C1Q-S225, S218, -S196, -S197, -S105, -S111, -S115C, -S116B
Fits HS 81 R, HS 81 RC, HS 81 T, HS 81 TC, HS 86 R, HS 86 T.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (35)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1123 122 3001 | Spring | 1 |
| 2 | 4116 121 5100 | Inlet needle | 1 |
| 3 | 1125 121 5000 | Inlet control lever | 1 |
| 4 | 1120 121 9200 | Spindle | 1 |
| 5 | 1120 122 6600 | Collar screw | 1 |
| 6 | 4229 129 0901 | Gasket | 1 |
| 7 | 4229 121 4700 | Metering diaphragm → replaced by 4314 121 4700, 4314 121 4700, 4314 121 4700 TI 18/2008 | 1 |
| 8 | 4237 120 2202 | Flange Fitment / change note → | 1 |
| 9 | 4226 121 2700 | Cap | 1 |
| 10 | 4140 121 0800 | End cover | 1 |
| 11 | 4226 122 7100 | Screw | 4 |
| 13 | 1129 121 4800 | Pump diaphragm | 1 |
| 14 | 1123 129 0905 | Gasket | 1 |
| 15 | 1123 121 0800 | End cover | 1 |
| 16 | 1125 122 4200 | Clamp | 1 |
| 17 | 4140 122 6200 | Idle speed adjustment screw | 1 |
| 18 | 1120 122 7800 | Oval head screw | 1 |
| 19 | 4128 121 8901 | Pin | 1 |
| 20 | 4137 121 8600 | Washer | 1 |
| 21 | 1120 122 9000 | E-clip | 1 |
| 22 | 4237 122 6800 | Low speed adjustment screw Fitment / change note → | 1 |
| 23 | 4229 122 6701 | High speed adjustment screw | 1 |
| 24 | 4229 121 2701 | Cap | 1 |
| 25 | 4237 182 9500 | Choke knob | 1 |
| 26 | 4237 121 5600 NLA | Fixed jet 0.38 | 1 |
| 27 | 1132 121 5640 | Fixed jet 0.40 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4237 120 0618 | Carburetor C1Q-S225 | 1 |
| — | 4237 120 0610 | Carburetor C1Q-S197 | 1 |
| — | 4237 120 0612 | Carburetor C1Q-S218 no longer available from factory | 1 |
| — | 4237 120 0609 | Carburetor C1Q-S196 no longer available from factory | 1 |
| — | 4237 120 0604 | Carburetor C1Q-S115C Fitment / change note → no longer available from factory | 1 |
| — | 4237 120 0601 NLA | Carburetor C1Q-S105 Fitment / change note → → replaced by 4237 120 0604 TI 64/2007 no longer available from factory | 1 |
| — | 4237 120 0605 | Carburetor C1Q-S116B no longer available from factory | 1 |
| — | 4237 120 0603 | Carburetor C1Q-S111 no longer available from factory | 1 |
| — | 4229 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HS 81 R / HS 81 T / HS 86 R / HS 86 T
HS 81 / HS 86: barbed carburetor, flange and low-speed screw
The hose clip remains necessary only with the previous smooth-connector carburetor.
- For the named HS 81 R / T and HS 86 R / T models, C1Q-S105 carburetor 4237 120 0601 is replaced by C1Q-S115 4237 120 0604. Figure 442TI048 shows previous smooth connector LEFT, new barbed connector RIGHT.
- Flange 4237 120 2200 becomes barbed flange 4237 120 2202; low-speed adjustment screw 4229 122 6801 becomes 4237 122 6800. The new C1Q-S115 INCLUDES the flange and screw (summary items 3 and 4). No screw-turn setting is supplied.
- Hose clip 4205 122 2500 is NO LONGER USED with the new carburetor but is STILL REQUIRED with old 4237 120 0601. Table remark 3 retains old clip factory availability, unlike old carburetor/flange/screw remark 1.
- Only the new carburetor is to be supplied; remark 2 allows new carburetor, flange and screw on older machines subject to the return-hose change. Later C1Q variants in the shared IPL title are navigation, not approval to apply this replacement to all of them.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 64/2007, p. 1 · TI 64/2007, p. 2 · TI 64/2007, p. 7 — HS 81 / HS 86: barbed carburetor, flange and low-speed screw.
Part numbers (7)
- 4237 120 0601 — C1Q-S105 carburetorPrevious; smooth connector · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 4237 120 0604 — C1Q-S115 carburetorNew; includes flange and screw · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 4237 120 2200 — FlangePrevious · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 4237 120 2202 — Barbed flangeNew · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 4229 122 6801 — Low-speed screwPrevious · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 4237 122 6800 — Low-speed screwNew · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 4205 122 2500 — Hose clipStill required with previous carburetor · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
Service note · HS 81 R / HS 81 T / HS 86 R / HS 86 T
HS 81 / HS 86: 190 mm versus 170 mm return-hose configurations
Changing the carburetor OR flange requires the new return-hose length.
- Previous carburetor: fuel RETURN hose 7.48 in (190 mm), pushed FULLY onto its housing connector and secured by the existing clip (figure 442TI049). New carburetor: return hose 6.70 in (170 mm), fully installed on the BARBED connector (442TI050). These are return-hose lengths, not supply-hose lengths.
- Section 1.1 requires shortening to 170 mm when replacing the previous carburetor OR previous flange with its new version. It promises an illustrated installation supplement with the new parts; this is not proof that the separate supplement was recovered.
- Section 1.3 also expressly says disconnected fuel hoses MUST NOT BE REUSED because removal may over-extend them. Preserve that requirement alongside the shortening wording: shortening is a configuration dimension, not permission to refit an old disconnected hose.
- The new tank has the shorter return hose, but a 190 mm return hose is enclosed for installation in older machines. Choose the configuration by the carburetor/connector requirements; the tank’s retrofit permission does not erase the length distinction.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 64/2007, p. 2 · TI 64/2007, p. 3 — HS 81 / HS 86: 190 mm versus 170 mm return-hose configurations.
No additional parts-table entry added.
Service note · HS 81 R / HS 81 T / HS 86 R / HS 86 T
HS 81 / HS 86: fuel-hose handling and assembly-fluid restriction
Disconnect and install hoses by hand; replace disconnected hoses.
- Fuel hoses must be disconnected and installed BY HAND to avoid damaging the barbed connector. Do not use sharp-edged pliers or screwdrivers on hoses and do not cut hoses open with a knife or similar implement.
- Disconnected hoses must ALWAYS be replaced with NEW hoses; possible over-extension prevents reuse. Fit new hoses DRY or with Press Fluid OH 723, order 0781 957 9000. If using it, coat the hose ends AND connectors before fitting.
- Press Fluid OH 723 forms a temporary lubricant film and evaporates shortly, allowing a tight fit. NEVER use FUEL, OIL OR GREASE as installation lubricant: they do not evaporate as required and may let the hose slip off.
- The separate instruction to gently pry the tank CONNECTOR by its tab does not authorize prying fuel HOSES off barbs.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 64/2007, p. 2 — HS 81 / HS 86: fuel-hose handling and assembly-fluid restriction.
Part numbers (1)
- 0781 957 9000 — Press Fluid OH 723Allowed hose assembly aid · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
Wrong number or missing part for the HS 81 R, HS 81 RC, HS 81 T, HS 81 TC, HS 86 R, HS 86 T? Report a correction →