← P 835, P 840

Stihl 4702 · Section A · 1 of 14 · 19 parts

Crankcase

Fits P 835, P 840.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11101112131415161723344566789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (19)

PosPart numberDescriptionQty
1 4702 020 2500 Crankcase 1
2 9371 470 3120 Cylindrical pin 6x20 2
3 9503 003 0341 Grooved ball bearing 6202 2
4 9640 003 1610 Oil seal 15x35x7 2
5 9121 319 1280 Stud M6x16 4
6 9456 621 3860 Circlip 35x1.5 2
7 9022 341 0900 Spline screw IS-M5x28 4
8 1108 030 0403 Crankshaft 1
9 9482 435 0390 Woodruff key 3x3 7 1
10 9470 435 0900 Key 5x3x14 1
11 9512 003 3140 Needle cage 12x16x13 1
12 4214 029 0500 Gasket 1
13 4702 080 0201 Fan involute 1
14 4702 080 0200 Fan involute 1
15 4702 448 1200 Lead retainer 1
16 9330 630 0100 Shake-proof washer 4.3 4
17 9022 313 0650 Spline screw IS-M4x10 4
Not numbered on the diagram — assemblies, kits and options
— 4702 007 1050 NLA Set of gaskets 1
— 4702 007 1051 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · P 835 / P 840

P 835 / P 840: original 56 cm³ engine and leakage-test data

Historical TI specifies engine dimensions, bearings and starter rope; no full test procedure is supplied.

  • Engine displacement 56 cm³; bore 47 mm; stroke 32 mm; compression 9.5:1. Power output 2.5 kW (3.4 PS) to DIN 70 020; maximum torque 3.7 Nm AT 5,000 rpm. Do not assign that speed as a rated-power speed or confuse output torque with a fastener torque.
  • Crankshaft is two-part, drop-forged, supported by TWO deep-groove ball bearings. Crankpin diameter 14.4 mm; big-end needle cage; connecting-rod length 58 mm; piston-pin diameter 12 mm; small-end needle cage. No individual bearing or crankshaft part numbers are given here.
  • Pawl rewind starter has automatic rope rewind. Starter rope is 4.5 mm diameter, 1000 mm long; source does not give rope part number or winding count.
  • Crankcase leakage test table prints 0.4 bar (5.8 psi) at gauge pressure AND 0.4 bar (5.8 psi) under VACUUM. Preserve the vacuum row as suction magnitude, not a second positive-pressure instruction. No allowable leakage, hold time or blanking setup is stated; these values alone are not a complete test procedure.
  • Historical TI 20/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 20/1994, p. 1 · TI 20/1994, p. 2 · TI 20/1994, p. 3 — P 835 / P 840: original 56 cm³ engine and leakage-test data.

No additional parts-table entry added.

Service note · P 835 / P 840

P 835 / P 840: tightening torque and adhesive depend on the exact joint

Twenty-five table rows retain component/thread mapping; four marked joints require Loctite 243.

  • Torque wrench is ESSENTIAL to achieve joint strength. Values below are Nm and apply to the printed component AND fastener, not a general thread-size rule. “Spline screw” wording follows the source; no unprinted part numbers inferred.
  • Spline screw M4×15, set of contacts: 1.0 Nm; M4×12, fanwheel: 7.0 Nm; IS-M4×16, armature plate: 3.3 Nm; IS-M4×25, carburetor flange: 3.3 Nm; nut VM5, filter port: 4.5 Nm.
  • Spline screw IS-M5×18, fan housing: 5.0 Nm; SAME thread/length, guard to fan housing: 2.8 Nm; IS-M5×25, guard to crankcase: 4.0 Nm; IS-M5×28, crankcase: 6.8 Nm; IS-M6×20, handle: 4.3 Nm WITH ADHESIVE; IS-M6×25, tank housing to crankcase housing: 7.0 Nm.
  • Spline screw M6×90, muffler to cylinder: 8.5 Nm; nut M6, muffler to housing: 8.5 Nm; spline screw IS-M6×20, cylinder: 9.5 Nm; IS-M5×18, shroud/crankcase housing: 2.0 Nm WITH ADHESIVE; nut M10×1, flywheel: 27.5 Nm; M14×1.25 spark plug: 25.0 Nm.
  • Spline screw B4.8×13, rubber buffer: 1.5 Nm; nut M6, inside of housing to engine: 8.5 Nm; nut M10×1 lks. (LEFT-HAND thread), rotor to crankshaft: 24.5 Nm WITH ADHESIVE; spline screw M4×19, ignition armature: 3.3 Nm; M4×10, air baffle to crankcase: 2.3 Nm WITH ADHESIVE.
  • Nut M6, intake port: 6.5 Nm; spline screw IS-M5×18, delivery port: 5.3 Nm; IS-M6×25, tank housing to pump housing: 7.0 Nm. Do not confuse intake and delivery fasteners or the two separate tank-housing joints.
  • Remark 1 requires adhesive 0786 111 1101 (LOCTITE 243) ONLY on four marked rows: handle, shroud/crankcase housing, rotor-to-crankshaft LEFT-HAND nut and air baffle to crankcase. Original scan aligns 2.0 Nm with shroud/crankcase and 27.5 Nm with flywheel; flattened text order must not swap them. Remark says “screw”, but its marker also explicitly applies to the rotor nut.
  • Source says adhesive-secured fasteners are easier to release after heating adhesive with a hot-air blower (hair dryer), with CAUTION on polymer components. No temperature, dwell time or permission to heat a fueled assembly is supplied. Housing-bond adhesive is not identified as this thread adhesive.
  • Historical TI 20/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 20/1994, p. 5 — P 835 / P 840: tightening torque and adhesive depend on the exact joint.

Part numbers (1)
  • 0786 111 1101 — LOCTITE 243 adhesivefour marked fastener joints only · P 835 / P 840: tightening torque and adhesive depend on the exact joint

Service note · P 835 / P 840

P 835 / P 840: historical workshop times and restricted trial run

Times assume trained personnel and a fully equipped shop; trial run is only with water or without the pump.

  • Same special tools as for 08 S chain saw may be used to repair the ENGINE UNIT of these pumps. This is not proof that every 08 S tool repairs the pump housing, nor whole-machine interchange; no special-tool numbers are printed.
  • Historical repair times in MINUTES for trained personnel and fully equipped customer repair shop: starter with pawls 15; shroud/air filter/carburetor/muffler 35; ignition module/switchgear/ignition armature 40; pump housing with impeller 20; cylinder and piston 60; crankcase and crankshaft 155; crankshaft bearings and rotary shaft seals 145; crankcase pressure test 30; trial run 5; tank 15; handle/stop switch/throttle control 5. These are quoted workshop allowances, not DIY completion promises or measurements.
  • Trial-run footnote: ONLY WITH WATER OR WITHOUT PUMP. Do not interpret a five-minute trial allowance as permission to run an assembled pump dry. Source requires applicable national safety rules and User Manual instructions when starting during repair/maintenance. No live test has been performed or authorized by this reference note.
  • Table is intended for insertion into page 15 of the STIHL repair-times table, by cutting/pasting or transcription. That document and User Manual are referenced, not accepted here as reviewed. Original publication footer is March 30, 1994.
  • Historical TI 20/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 20/1994, p. 6 — P 835 / P 840: historical workshop times and restricted trial run.

No additional parts-table entry added.

Wrong number or missing part for the P 835, P 840? Report a correction →