Stihl 4702 · Section B · 2 of 14 · 32 parts
Cylinder, Muffler
Fits P 835, P 840.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (32)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1108 029 2300 | Cylinder gasket | 1 |
| 2 | 4702 020 1200 | Cylinder with piston Ø 47 mm | 1 |
| 3 | 1108 030 2020 | Piston Ø 47 mm | 1 |
| 4 | 1108 034 3001 | Piston ring Ø 47x1.5 mm | 2 |
| 5 | 1108 034 1501 | Piston pin 12x8x33 | 1 |
| 6 | 9463 650 1200 | Snap ring 12x1 | 2 |
| 7 | 9022 341 1300 | Spline screw IS-M6x20 | 6 |
| 8 | 1107 400 7000 NLA | Spark plug Bosch WR 7 AC | 1 |
| 8 | 1108 400 7000 | Spark plug B6HS | 1 |
| 9 | 1108 405 1000 | Spark plug boot | 1 |
| 10 | 0000 998 0603 | Torsion spring → replaced by 0000 998 0604 TI 30/1995 | 1 |
| 11 | 1108 149 0600 | Muffler gasket | 1 |
| 13 | 4702 145 0700 | Inlet casing | 1 |
| 14 | 4702 145 0805 | Exhaust casing | 1 |
| 15 | 4702 141 1500 | Flange | 1 |
| 16 | 9099 021 0805 | Self-tapping screw 4.2x6.5 | 1 |
| 17 | 9330 630 0100 | Shake-proof washer 4.3 | 1 |
| 18 | 9099 021 0810 | Self-tapping screw 4.2x9.5 | 1 |
| 19 | 4201 141 9001 NLA | Screen | 1 |
| 20 | 9220 260 0901 | Hexagon nut M6 | 2 |
| 21 | 0000 953 1024 | Stud M6x30 → replaced by 9121 347 1370 TI 9/1994 | 1 |
| 22 | 4201 140 7200 | Muffler guard | 1 |
| 23 | 9416 868 7030 | Hollow rivet 7x0.5x6.8 | 1 |
| 24 | 9022 341 1050 | Spline screw IS-M5x25 | 1 |
| 25 | 9022 341 1010 | Spline screw IS-M5x18 | 1 |
| 26 | 9008 319 1010 | Hexagon head screw M5x18 | 1 |
| 27 | 9307 021 0120 | Washer 5.3 | 1 |
| 40 | 9022 341 1520 | Spline screw IS-M6x90 | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4702 140 0650 | Muffler | 1 |
| — | 4702 140 0651 | Muffler | 1 |
| — | 4702 007 1050 NLA | Set of gaskets | 1 |
| — | 4702 007 1051 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · P 835 / P 840
P 835 / P 840: original 56 cm³ engine and leakage-test data
Historical TI specifies engine dimensions, bearings and starter rope; no full test procedure is supplied.
- Engine displacement 56 cm³; bore 47 mm; stroke 32 mm; compression 9.5:1. Power output 2.5 kW (3.4 PS) to DIN 70 020; maximum torque 3.7 Nm AT 5,000 rpm. Do not assign that speed as a rated-power speed or confuse output torque with a fastener torque.
- Crankshaft is two-part, drop-forged, supported by TWO deep-groove ball bearings. Crankpin diameter 14.4 mm; big-end needle cage; connecting-rod length 58 mm; piston-pin diameter 12 mm; small-end needle cage. No individual bearing or crankshaft part numbers are given here.
- Pawl rewind starter has automatic rope rewind. Starter rope is 4.5 mm diameter, 1000 mm long; source does not give rope part number or winding count.
- Crankcase leakage test table prints 0.4 bar (5.8 psi) at gauge pressure AND 0.4 bar (5.8 psi) under VACUUM. Preserve the vacuum row as suction magnitude, not a second positive-pressure instruction. No allowable leakage, hold time or blanking setup is stated; these values alone are not a complete test procedure.
- Historical TI 20/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 20/1994, p. 1 · TI 20/1994, p. 2 · TI 20/1994, p. 3 — P 835 / P 840: original 56 cm³ engine and leakage-test data.
No additional parts-table entry added.
Wrong number or missing part for the P 835, P 840? Report a correction →