← P 835, P 840

Stihl 4702 · Section C · 3 of 14 · 15 parts

Ignition system

Fits P 835, P 840.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111223456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (15)

PosPart numberDescriptionQty
1 0000 989 0810 Grommet 1
2 0000 989 0816 Grommet 1
3 1108 400 0804 Ignition module 1
4 not sold separately Ignition lead 325 mm not available as a separate item 1
5 0000 989 1010 Grommet 1
6 1125 440 1100 Short circuit wire 270 mm / 10.6'' 1
7 1119 442 7000 Contact sleeve no longer available from factory 1
8 0751 030 8957 Terminal socket 4.8-1/0.8 no longer available from factory 1
9 1108 400 1205 Flywheel 1
10 9022 313 0680 Spline screw IS-M4x16 2
11 9291 021 0100 Washer 4.3 2
12 9211 260 1340 Hexagon nut M10x1 1
Not numbered on the diagram — assemblies, kits and options
— 0000 405 0600 NLA Ignition lead 1 m not illustratedoption 1
— 0000 930 2251 Ignition lead 10 m not illustratedoption 1
— 0751 010 1110 Lead 10 m / 33' option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · P 835 / P 840

P 835 / P 840: contact ignition and Bosch WR 7 AC specification

Timing is piston travel before top dead centre; plug gap is not ignition-contact gap.

  • Original system is CONTACT IGNITION. Ignition timing 2.0–2.4 mm B.T.D.C. is piston position BEFORE TOP DEAD CENTRE, not degrees or an electronic-module air gap. Source does not specify contact-point gap.
  • Spark plug Bosch WR 7 AC, electrode gap 0.5 mm, thread M14×1.25 with 12.7 mm thread length, printed heat range 175. No numeric STIHL plug part number is supplied; no cross-brand heat-range conversion or later ignition applicability is inferred.
  • Historical TI 20/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 20/1994, p. 3 — P 835 / P 840: contact ignition and Bosch WR 7 AC specification.

No additional parts-table entry added.

Service note · P 835 / P 840

P 835 / P 840: tightening torque and adhesive depend on the exact joint

Twenty-five table rows retain component/thread mapping; four marked joints require Loctite 243.

  • Torque wrench is ESSENTIAL to achieve joint strength. Values below are Nm and apply to the printed component AND fastener, not a general thread-size rule. “Spline screw” wording follows the source; no unprinted part numbers inferred.
  • Spline screw M4×15, set of contacts: 1.0 Nm; M4×12, fanwheel: 7.0 Nm; IS-M4×16, armature plate: 3.3 Nm; IS-M4×25, carburetor flange: 3.3 Nm; nut VM5, filter port: 4.5 Nm.
  • Spline screw IS-M5×18, fan housing: 5.0 Nm; SAME thread/length, guard to fan housing: 2.8 Nm; IS-M5×25, guard to crankcase: 4.0 Nm; IS-M5×28, crankcase: 6.8 Nm; IS-M6×20, handle: 4.3 Nm WITH ADHESIVE; IS-M6×25, tank housing to crankcase housing: 7.0 Nm.
  • Spline screw M6×90, muffler to cylinder: 8.5 Nm; nut M6, muffler to housing: 8.5 Nm; spline screw IS-M6×20, cylinder: 9.5 Nm; IS-M5×18, shroud/crankcase housing: 2.0 Nm WITH ADHESIVE; nut M10×1, flywheel: 27.5 Nm; M14×1.25 spark plug: 25.0 Nm.
  • Spline screw B4.8×13, rubber buffer: 1.5 Nm; nut M6, inside of housing to engine: 8.5 Nm; nut M10×1 lks. (LEFT-HAND thread), rotor to crankshaft: 24.5 Nm WITH ADHESIVE; spline screw M4×19, ignition armature: 3.3 Nm; M4×10, air baffle to crankcase: 2.3 Nm WITH ADHESIVE.
  • Nut M6, intake port: 6.5 Nm; spline screw IS-M5×18, delivery port: 5.3 Nm; IS-M6×25, tank housing to pump housing: 7.0 Nm. Do not confuse intake and delivery fasteners or the two separate tank-housing joints.
  • Remark 1 requires adhesive 0786 111 1101 (LOCTITE 243) ONLY on four marked rows: handle, shroud/crankcase housing, rotor-to-crankshaft LEFT-HAND nut and air baffle to crankcase. Original scan aligns 2.0 Nm with shroud/crankcase and 27.5 Nm with flywheel; flattened text order must not swap them. Remark says “screw”, but its marker also explicitly applies to the rotor nut.
  • Source says adhesive-secured fasteners are easier to release after heating adhesive with a hot-air blower (hair dryer), with CAUTION on polymer components. No temperature, dwell time or permission to heat a fueled assembly is supplied. Housing-bond adhesive is not identified as this thread adhesive.
  • Historical TI 20/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 20/1994, p. 5 — P 835 / P 840: tightening torque and adhesive depend on the exact joint.

Part numbers (1)
  • 0786 111 1101 — LOCTITE 243 adhesivefour marked fastener joints only · P 835 / P 840: tightening torque and adhesive depend on the exact joint

Wrong number or missing part for the P 835, P 840? Report a correction →