Stihl 4702 · Section E · 5 of 14 · 21 parts
Rewind starter
Fits P 835, P 840.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (21)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4702 080 1801 | Fan housing | 1 |
| 2 | 1110 084 9102 | Bushing | 1 |
| 3 | 9443 825 7130 | Hollow rivet 7.5x1x6.8 | 3 |
| 4 | 9416 868 6630 | Hollow rivet 6.5x0.5x6.8 | 3 |
| 5 | 0000 967 2020 NLA | Nameplate STIHL | 1 |
| 6 | 0000 967 2018 | Nameplate STIHL | 1 |
| 7 | 0000 974 1000 | Round head rivet 3x6 | 2 |
| 8 | 4221 084 5600 | Screw | 1 |
| 9 | 1108 195 9000 | Washer | 1 |
| 10 | 1118 190 0600 | Rewind spring | 1 |
| 11 | 1118 195 0300 | Spring housing | 1 |
| 12 | 1122 195 0400 | Rope rotor | 1 |
| 13 | 1107 195 8200 | Starter rope Ø 4.5x1000 mm | 1 |
| 14 | 1124 195 7200 | Pawl | 1 |
| 15 | 1118 162 8935 | Washer | 1 |
| 16 | 1117 195 3500 | Spring | 1 |
| 17 | 1121 195 3400 | Starter grip | 1 |
| 18 | 9022 341 1010 | Spline screw IS-M5x18 | 2 |
| 19 | 9210 260 0700 | Hexagon nut M5 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4702 080 2101 | Fan housing with rewind starter | 1 |
| — | 0000 930 2213 NLA | Starter rope Ø 4.5 mm x 60.8 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · P 835 / P 840
P 835 / P 840: original 56 cm³ engine and leakage-test data
Historical TI specifies engine dimensions, bearings and starter rope; no full test procedure is supplied.
- Engine displacement 56 cm³; bore 47 mm; stroke 32 mm; compression 9.5:1. Power output 2.5 kW (3.4 PS) to DIN 70 020; maximum torque 3.7 Nm AT 5,000 rpm. Do not assign that speed as a rated-power speed or confuse output torque with a fastener torque.
- Crankshaft is two-part, drop-forged, supported by TWO deep-groove ball bearings. Crankpin diameter 14.4 mm; big-end needle cage; connecting-rod length 58 mm; piston-pin diameter 12 mm; small-end needle cage. No individual bearing or crankshaft part numbers are given here.
- Pawl rewind starter has automatic rope rewind. Starter rope is 4.5 mm diameter, 1000 mm long; source does not give rope part number or winding count.
- Crankcase leakage test table prints 0.4 bar (5.8 psi) at gauge pressure AND 0.4 bar (5.8 psi) under VACUUM. Preserve the vacuum row as suction magnitude, not a second positive-pressure instruction. No allowable leakage, hold time or blanking setup is stated; these values alone are not a complete test procedure.
- Historical TI 20/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 20/1994, p. 1 · TI 20/1994, p. 2 · TI 20/1994, p. 3 — P 835 / P 840: original 56 cm³ engine and leakage-test data.
No additional parts-table entry added.
Wrong number or missing part for the P 835, P 840? Report a correction →