← P 835, P 840

Stihl 4702 · Section F · 6 of 14 · 35 parts

Air filter, Shroud

Fits P 835, P 840.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1110111213141516171819220212223242526272829293303132456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (35)

PosPart numberDescriptionQty
1 1108 129 1110 Gasket 2
2 4214 121 2200 Cooling plate 1
3 9214 320 0900 Lock nut M6 2
4 1108 120 2300 Spacer flange 1
5 9022 313 0740 Spline screw IS-M4x25 4
6 1108 129 1103 Gasket 1
7 1108 121 1610 Flange 1
8 1108 122 8000 Stud 2
9 9022 341 1350 Spline screw IS-M6x25 2
10 1108 129 1111 Gasket 1
11 4702 120 0604 Carburetor WJ-113 1
12 4702 120 0603 Carburetor HS-271D 1
13 4702 120 0602 Carburetor HS-271B 1
14 4702 120 0602 Carburetor HS-271B 1
15 4702 121 7701 Clamp option 1
16 4702 121 7700 Clamp 1
17 4702 121 7700 Clamp 1
18 1117 122 9000 E-clip option 1
19 9099 021 2360 Self-tapping screw 3.5x9.5 option 1
20 9099 021 2360 Self-tapping screw 3.5x9.5 1
21 1123 120 1612 Air filter 1
22 4702 124 3500 Filter housing 1
23 9216 261 0700 Hexagon nut M5 2
24 not sold separately Carburetor box cover not available as a separate item 1
25 1123 141 2300 Twist lock 1
26 4702 432 2000 Slide 1
27 4702 431 6500 Contact spring 1
28 9103 021 0160 Self-tapping screw 2.2x6.5 1
29 4702 121 6600 Choke lever 2
30 4702 080 1606 Shroud 1
31 4702 084 8300 Reflector foil 1
32 9022 341 1010 Spline screw IS-M5x18 2
Not numbered on the diagram — assemblies, kits and options
— 4702 120 1600 Air filter 1
— 4702 140 1901 Carburetor box cover 1
— 4702 007 1051 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · P 835 / P 840

P 835 / P 840: historical fuel system settings and oil-dependent mixture

H and L are each approximately one turn; original oil distinctions remain explicit.

  • All-position diaphragm carburetor has integral fuel pump. Standard H high-speed and L low-speed adjusting screws are EACH backed off APPROXIMATELY ONE TURN. No carburetor model, final speed setting or limiter-removal instruction is given; do not silently bind these values to later carburetor variants.
  • Carburetor leakage-test gauge pressure 0.4 bar (5.8 psi); no hold time or acceptable leak rate stated. Fuel tank 2.65 litres (2650 cm³); minimum octane 90 RON, not 90 AKI.
  • Historical fuel specification: regular brand-name gasoline with brand-name two-stroke engine oil; mix 1:50 WITH STIHL two-stroke engine oil 1:50, but 1:40 WITH OTHER brand-name two-stroke engine oils. Preserve that source distinction rather than choosing one universal ratio. Round air filter with foam. This is the March 1994 specification, not an assertion about every modern oil or fuel formulation.
  • Historical TI 20/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 20/1994, p. 3 — P 835 / P 840: historical fuel system settings and oil-dependent mixture.

No additional parts-table entry added.

Wrong number or missing part for the P 835, P 840? Report a correction →