Stihl 4901 · Section A · 1 of 11 · 37 parts
Machine cover, Motor housing
Fits SE 100, SE 200, SE 201, SE 202.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (37)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4709 700 2100 | Machine cover | 1 |
| 2 | 4709 706 3200 | Soundproofing liner no longer available from factory | 1 |
| 3 | 4709 706 3205 | Soundproofing liner | 1 |
| 4 | 4709 706 3500 | Push nut | 4 |
| 5 | 4727 608 9000 | Rubber ring | 1 |
| 6 | 4709 706 3215 | Soundproofing liner | 1 |
| 7 | 4709 700 6600 | Air diverter | 1 |
| 8 | not sold separately | Soundproofing liner not available as a separate item | 1 |
| 9 | 4709 706 1800 | Spring catch | 4 |
| 10 | 4709 703 4100 | Handle no longer available from factory | 1 |
| 11 | 9063 319 8110 | Countersunk screw M6x90 | 2 |
| 12 | 4714 703 3800 | Sleeve | 1 |
| 13 | 9210 260 0755 | Hexagon nut R1/2" | 1 |
| 14 | 4714 706 1800 | Clip no longer available from factory | 1 |
| 15 | 4709 600 0800 | Motor housing | 1 |
| 16 | 4709 706 3225 | Soundproofing liner | 1 |
| 17 | 4709 706 3230 | Soundproofing liner | 1 |
| 18 | 4709 706 3235 | Soundproofing liner | 1 |
| 19 | 4709 706 3500 | Push nut | 10 |
| 20 | 4709 706 3240 | Soundproofing liner | 1 |
| 21 | 4713 431 2900 | Terminal block no longer available from factory | 1 |
| 22 | 9104 003 8650 | Self-tapping screw P3.5x18 | 3 |
| 23 | 4709 600 2900 | Module | 1 |
| 24 | 9104 003 9939 | Self-tapping screw P3.5x10 | 2 |
| 25 | 4709 605 1201 | Interference suppressor capacitor Fitment / change note → | 1 |
| 25 | 4709 605 1206 | Interference suppressor capacitor Fitment / change note → | 1 |
| 26 | 9189 021 2860 | Wood screw 3.5x50 | 1 |
| 27 | 4703 431 2500 | Cable clamp | 1 |
| 28 | 9104 003 8778 | Self-tapping screw P5x20 | 3 |
| 29 | 4901 440 2000 | Connecting cable | 1 |
| 30 | 4901 440 2030 | Connecting cable | 1 |
| 31 | 4901 440 2010 | Connecting cable | 1 |
| 32 | 4703 440 2000 | Connecting cable GB 110 V | 1 |
| 33 | 4901 440 2020 | Connecting cable | 1 |
| 34 | 4709 440 2000 | Connecting cable | 1 |
| 50 | 4709 605 1200 | Interference suppressor capacitor Fitment / change note → | 1 |
| 50 | 4709 605 1205 | Interference suppressor capacitor Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · SE 100 / SE 200 / SE 201 / SE 202
SE 100 / 200 / 201 / 202: motor conversion preserves locking-pin alignment
Transfer the upper ring, align opposite pins and reconnect mains at filter markings A and B.
- Expert-electrician procedure: remove vacuum top; remove TWO handle Phillips screws and handle; invert top, remove THREE Phillips screws shown, return top upright. Remove THREE clamping-plate Phillips screws and plate. Remove old motor with earth connection and upper bearing ring; remove TWO hex-socket bolts(1) and upper ring.
- Engage locking pins(2) OPPOSITE one another in new motor. Align upper-ring holes with pins and fit ring. Place motor in support plate; turn clamping plate until pins align with its recesses, then insert/tighten three Phillips screws. Diagram distinguishes old bolted ring from pin alignment; no tightening torque supplied.
- If present, REMOVE OLD thermal safeguard with main cable from clamping plate; new motor already has built-in safeguard. Hook main cable to suppression-filter markings A and B. Replace cover/handle in reverse order. DO NOT EARTH NEW CLASS II MOTOR. This is not permission to omit built-in protection or the outlet earth. Test electrical/technical safety to IEC335 after conversion.
- Historical TI 29/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply statements are historical, not current availability. No physical interchange test was performed.
- Exact vacuum models are grouped under catalogue series4901, despite TI type4709/4714. Sheet C is SE100 motor/filter; sheet D is SE200/201/202; shared sheets A/B cover housing and switches. Shared sheet labels do not broaden this note’s explicit model scope.
Source: TI 29/1994, p. 1 · TI 29/1994, p. 2 — SE 100 / 200 / 201 / 202: motor conversion preserves locking-pin alignment.
No additional parts-table entry added.
Service note · SE 100 / SE 200 / SE 201 / SE 202
SE 100 / 200 / 201 / 202: suppression-capacitor variants remain separate
General and S/N/SF/GB 120 V rows change numbers; both original parts remain supplied.
- General suppression capacitor 4709 605 1200→4709 605 1201; separate row labelled S/N/SF/GB120V is 4709 605 1205→4709 605 1206. Original parts STILL AVAILABLE(remark2). Introduction IN PROGRESS, no serial.
- No capacitance, voltage equivalence, universal substitution or120V replacement motor is established by this capacitor row. Expert-electrician restriction and post-conversion IEC335 test remain applicable.
- Historical TI 29/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply statements are historical, not current availability. No physical interchange test was performed.
- Exact vacuum models are grouped under catalogue series4901, despite TI type4709/4714. Sheet C is SE100 motor/filter; sheet D is SE200/201/202; shared sheets A/B cover housing and switches. Shared sheet labels do not broaden this note’s explicit model scope.
Source: TI 29/1994, p. 3 — SE 100 / 200 / 201 / 202: suppression-capacitor variants remain separate.
Part numbers (4)
- 4709 605 1200 — Suppression capacitorold still available · SE 100 / 200 / 201 / 202: suppression-capacitor variants remain separate
- 4709 605 1201 — Suppression capacitornew · SE 100 / 200 / 201 / 202: suppression-capacitor variants remain separate
- 4709 605 1205 — S/N/SF/GB120V suppression capacitorold still available · SE 100 / 200 / 201 / 202: suppression-capacitor variants remain separate
- 4709 605 1206 — S/N/SF/GB120V suppression capacitornew · SE 100 / 200 / 201 / 202: suppression-capacitor variants remain separate
Service note · SE 100 / SE 200 / SE 202
SE 100 / 200 / 202: automatic-switch kit removes half-power mode
230–240 V kit 4901 007 1000 changes position I to maximum speed and position II to accessory-triggered operation.
- Kit 4901 007 1000 is230–240V ONLY; no120V or SE201 applicability. PositionI: vacuum runs MAXIMUM RPM because power-halving device must be removed. PositionII: built-in outlet ON, vacuum turns on with an accessory at that outlet (example grinding-machine extraction). Source literally says device plugged in; no current threshold, delay, load rating or guarantee that an idle plugged-in tool triggers it is supplied.
- Expert electrician: dismantle handle/cover as preceding section; disconnect all cables EXCEPT CONNECTING CABLE; REMOVE output-halving unit(3). Slide switch board(4) into holding frame and SNAP frame onto AIR-INTAKE SCREEN. Wire to page7, then replace cover/handle in reverse order. After conversion electrical/technical safety MUST be tested to IEC335. No installation torque, PCB part number or revised manual acceptance inferred.
- Historical TI 29/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply statements are historical, not current availability. No physical interchange test was performed.
- Exact vacuum models are grouped under catalogue series4901, despite TI type4709/4714. Sheet C is SE100 motor/filter; sheet D is SE200/201/202; shared sheets A/B cover housing and switches. Shared sheet labels do not broaden this note’s explicit model scope.
Source: TI 29/1994, p. 6 · TI 29/1994, p. 7 — SE 100 / 200 / 202: automatic-switch kit removes half-power mode.
Part numbers (1)
- 4901 007 1000 — Automatic switching retrofit230–240Vnew kit;SE100/200/202 only · SE 100 / 200 / 202: automatic-switch kit removes half-power mode
Wrong number or missing part for the SE 100, SE 200, SE 201, SE 202? Report a correction →