Stihl 1106 · Section A · 1 of 17 · 31 parts
Crankcase
Fits 070.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (31)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1106 020 2100 | Crankcase | 1 |
| 2 | 9121 347 1420 | Stud M6x45 | 2 |
| 3 | 9121 347 1370 | Stud M6x30 | 3 |
| 4 | 9371 470 3220 | Cylindrical pin 6x36 | 2 |
| 5 | 9321 630 0140 | Spring washer 6 | 5 |
| 6 | 9210 319 0900 | Hexagon nut M6 | 5 |
| 7 | 0000 989 0810 | Grommet | 1 |
| 8 | 0000 988 5217 | Connector | 1 |
| 9 | 0000 988 5200 | Connector | 2 |
| 10 | 1106 104 0200 | Bearing bushing | 1 |
| 11 | 0000 967 3662 | Warning pictogram MS | 1 |
| 12 | 1106 641 3200 | Oil line Fitment / change note → | 1 |
| 13 | 1106 640 3301 | Oil line Fitment / change note → | 1 |
| 14 | 9636 965 0640 | Sealing ring 8x12 Fitment / change note → | 4 |
| 15 | 9170 794 0230 | Banjo bolt 2/3" Fitment / change note → | 2 |
| 16 | 0000 989 5200 | Hose 43 mm / 1 3/4'' | 1 |
| 17 | 9456 621 3310 | Circlip 30x1.2 | 2 |
| 18 | 0000 958 2004 | Washer | 2 |
| 19 | 0000 993 0900 | Needle bearing 18x30x24 | 2 |
| 20 | 1106 036 9000 | Check ring | 2 |
| 21 | 9640 003 1981 | Oil seal 18x30x7 | 2 |
| 22 | 1106 029 8901 | Insulating rod | 1 |
| 23 | 1106 030 0400 | Crankshaft | 1 |
| 24 | 1106 029 1210 | Gasket | 1 |
| 25 | 1107 350 0500 | Filler cap | 1 |
| 26 | 1117 350 0905 | Filler cap retainer | 1 |
| 27 | 9099 021 2360 | Self-tapping screw 3.5x9.5 | 1 |
| 28 | 9645 948 4050 | O-ring 36x3 → replaced by 9645 951 3890 TI 34/2006 | 1 |
| 29 | 1108 350 5800 | Tank vent | 1 |
| 30 | 0000 951 5815 | Grub screw 1/4" | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1106 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 070 / 090
070 / 090: press-fit oil line and crankcase support
Changed crankcase holes and slight preload belong to the new oil-line design.
X 30 676 407 — 070/090 oil-line and crankcase modification only.
- From X 30 676 407, the oil line is press-fitted into the crankcase. The shape and size of the original tapped holes changed; this is NOT evidence that the new line simply substitutes into an unchanged older crankcase.
- The new line needs slight preload for tightness. A slightly raised portion on the unmachined cylinder-flange surface supports it. Figure 106TI001 distinguishes old bolted line 1 from new press-fit line 2; 106TI002 shows the new line in the crankcase. No preload value, press force, hole dimensions or machining conversion procedure is printed.
- A suitable piece of wire may be used to CAREFULLY clean the new oil line; the source gives no wire gauge or universal cleaning instruction. This cutoff applies to the oil-line/crankcase change, NOT the ignition screw or front-handle change. Model 090 G is not named by this TI, despite sharing an IPL sheet.
- Historical TI 43/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.
Source: TI 43/1994, p. 1 · TI 43/1994, p. 2 — press-fit oil line and crankcase support.
No additional parts-table entry added.
Service note · 070 / 090
070 / 090: oil-line parts and retained older-machine fasteners
The new press-fit line omits the old hollow screws and sealing rings; old parts remain listed for older machines.
X 30 676 407 — 070/090 oil line only;not other TI43 changes.
- Oil line 1106 640 3301 becomes 1106 641 3200, MOQ 1. Old hollow screws 9170 794 0230 (2x) and sealing rings 9636 965 0640 (4x) have dashes in the new-version column, not substitute numbers.
- Remark 1 applies to all three old rows: original parts remain available for OLDER MACHINES. Two screws and four rings are installed quantities, not MOQs; their MOQ cells are blank. The altered crankcase and preload requirements govern the new line; old availability does not establish mutual interchangeability.
- Historical TI 43/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.
Source: TI 43/1994, p. 1 · TI 43/1994, p. 2 — oil-line parts and retained older-machine fasteners.
Part numbers (4)
- 1106 640 3301 — Original oil lineretained for older machines · 070 / 090 only in the version/configuration described here
- 1106 641 3200 — New press-fit oil lineMOQ 1; modified crankcase required · 070 / 090 only in the version/configuration described here
- 9170 794 0230 — Original hollow screw; 2xretained for older machines · 070 / 090 only in the version/configuration described here
- 9636 965 0640 — Original sealing ring; 4xretained for older machines · 070 / 090 only in the version/configuration described here
Service note · 070 / 090
070 / 090 press-fit oil line: two different removal punches
3.5 mm at A (bar mount); 4.5 mm at B (oil pump).
- Applies to the PRESS-FITTED oil line 1106 641 3200 on 070 and 090. The TI points to TI43/1994 for its introduction; TI26 gives no new production cutoff and does not authorize converting an older threaded-line crankcase.
- For repair, knock the faulty line out of the crankcase using PIN PUNCHES: 3.5 mm (9/64 inch) diameter at A, the BAR MOUNT; 4.5 mm (3/16 inch) at B, the OIL PUMP. These are different tool diameters at different ends, not hole-drilling dimensions or interchangeable punch choices.
- Original figure 106TI004 K and printed prose clearly label A and B. The extracted body substitutes $ and % at these locations; use the scan labels, not those extraction artifacts. Preserve the printed metric/inch pairs as nominal source values.
- Later 070 A sheet key12 and shared 090/090 G A sheet key4 list this oil line. The shared sheet does not add 090 G to the TI scope. No punch ordering number, force, crankcase heating or hole reaming specification is supplied.
- Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.
Source: TI 26/1995, p. 1 — Service note removal and figure 106TI004 K.
Part numbers (1)
- 1106 641 3200 — Press-fitted oil linerepair removal; stated version only · 070 / 090; Service note removal and figure 106TI004 K
Service note · 070 / 090
070 / 090 press-fit oil line: drive on the flange
Screwdriver tip or suitable tool bears on the flange, not the tube span.
- To install oil line 1106 641 3200, use a screwdriver or other suitable tool to drive the line into the crankcase: apply the tip TO THE FLANGE OF THE OIL LINE and drive it home with FIRM BLOWS. This does not specify striking the unsupported tube span.
- Figure 106TI005 K shows arrows at the two seating ends and the screwdriver bearing at the flange. It supplies no numbered insertion order, numeric seating depth, interference, force or leak-test limit; do not turn the sketch into an invented complete assembly procedure.
- TI43/1994 is the cited predecessor, not a missing TI26 page. Earlier design/introduction requirements are not superseded by this repair note. Footer April 6, 1995, D1/MTK-al; no additional service assertion in the footer.
- Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.
Source: TI 26/1995, p. 1 — Service note installation, figure 106TI005 K and footer.
Part numbers (1)
- 1106 641 3200 — Press-fitted oil lineinstallation at flange · 070 / 090; Service note installation, figure 106TI005 K and footer
Wrong number or missing part for the 070? Report a correction →